Hostname: page-component-cd9895bd7-fscjk Total loading time: 0 Render date: 2024-12-28T21:57:53.057Z Has data issue: false hasContentIssue false
  • English
  • Français

Residual Stresses in Railroad Car Wheels*

Published online by Cambridge University Press:  06 March 2019

J. Jo ,
R.W. Hendricks ,
R.E. Swanson  and
R.V. Foutz
J. Jo
Affiliation:
Materials Engineering Department
R.W. Hendricks
Affiliation:
Materials Engineering Department
R.E. Swanson
Affiliation:
Materials Engineering Department
R.V. Foutz
Affiliation:
Statistics Department Virginia Polytechnic Institute and State University Blacksburg, Virginia 24061
Get access

Abstract

A new failure criterion for discriminating good and bad (overheated) railroad car wheels is proposed using X-ray residual stress data. The procedure for the new discrimination criterion is based on the fluctuations of the azimuthal residual stress in the tread of the wheel. This criterion is based on a maximum likelihood statistical analysis of stress data obtained from six different wheels as determined by x-ray diffraction. Of these locations, the analysis showed the tread, and perhaps a critical point on the top of the flange, to be the most sensitive to residual stress. The variance analysis showed that fluctuations in stress a.l the most sensitive location in the tread to be related to the service history. The residual stresses showed an oscillatory pattern in the hoop direction around the wheels. Extension of the measurement technology to the use of faster residual stress measurements is proposed. To validate our x-ray residual stress data, residual stresses were also measured by hole drilling. Excellent agreement between two techniques was found.

Type
XII. Analysis of Stress and Fracture by Diffraction Methods
Information
Advances in X-Ray Analysis , Volume 34: Thirty-Ninth Annual Conference on Applications of X-ray Analysis, July 30 - August 3, 1990 , 1990 , pp. 611 - 622
Copyright
Copyright © International Centre for Diffraction Data 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

*

This research was supported both financially and technically by the CSX Transportation Co. and by the Institute for Materials Science and Engineering of Virginia's Center for Innovative Technology.

References

[l] Stone, D. H., “Wheel Failure Due to Brake Heating”, Eighth International Wheelset Conference. Spain (1985).Google Scholar
[2] Barton, J. R.. Perry, W. D., and Swanson, R. K., “Heat-Discolored: Safe To Reuse?”, Progressive Railroading, pp. 41-48 (March 1985).Google Scholar
[3] Stone, D. H., (personal communication), AAR, Chicago (1985).Google Scholar
[4] Wentenkamp, H. R. and Eck, B. J., “Wheel Damage Caused by Overheating”, Car Department Officers Association Annual Meeting, Chicago (Sept. 20, 1982).Google Scholar
[5] Eck, B. J., “Development of the Curved Plate Wheel Designs for More Severe Railroad Service”, ASME 85-WA/RT-5 (1985).Google Scholar
[6] Wentenkamp, H. R. and Kipp, R. M., “Safe Thermal Load”, Proc. Sixth International Wheelset Congress, Colorado Springs (Oct. 1978).Google Scholar
[7] Carter, C. S., Caton, R. G., and Guthrie, J. L., “Fracture Resistance and Fatigue Crack Growth Characteristics of Railroad Wheels and Axles”, Department of Transportation Contract DOT-TSC 7, Final Report (April 1976).Google Scholar
[8] Opinsky, A. J., “Railroad Wheel Back Rim Pace Failures II. Fracture Mechanics Calculations Ba.sed on Measured Crack Sizes”, Association of American Railroads Report R-507, AAR Technical Center, Chicago, Illinois (1982).Google Scholar
[9] Pasley, R. H., “Barkhauscn Effect - An Indicator of Stress”, Materials Evaluation, 20(7), pp. 157–161 (1970).Google Scholar
[10] Johnson, M. R., Robinson, R. R., Opinsky, A. J., Joerms, M. W..and Stone, D. H., “Calculation of Residual Stresses in Wheels from a Saw Cut Displacement Data”, The Winter Annual Meeting (ASME). Miami Beach, Florida, (Nov.1985).Google Scholar
[11] Jones, H. J., “The Characterization of the Residual Stress State of a Railroad Wheels by the Saw Cut Method”, ASME Rail Transp. Spring Conf. Proc, pp. 15-19 (April 1985).Google Scholar
[12] Rajkumar, B. R. and Stone, D. H., “Measurement Approaches for Determining Thermally-Induced Residual Stresses in Railroad Wheels”, The Winter Annual Mccting(ASME), Miami Beach, Florida, (Nov.1985).Google Scholar
[13] Namkung, M., Ultra, D., Allison, S. C., and Heyman, J. S., “Low-field Magnetoacoustic Residual Stress Measurements in Steel”, Solid Mechanics Research for QNDE, Northwestern University, Evanston, IL (Sep. 1985).Google Scholar
[14] Ranganathan, B. N., Wert, J. J., and Clotfelter, W. N., J. of Test. Eval., 4, pp. 218–219 (1976).Google Scholar
[15] Jo, J., “Residual Stress Measurement in Railroad Car Wheels”, Ph.D. Dissertation, Virginia Polytechnic Institute and State University, Blacksburg, Virginia, (1989).Google Scholar
[16] Flaman, M. T., “Brief Investigation of Induced Drilling Stress in the Center Hole Method of Residual Stress Measurements”, Experimental Mechanics, 25 pp. 205–207 (1985).Google Scholar
[17] “Measurement of Residual Stresses by the Hole Drilling Strain Gage Method”, Measurement Group Tech Note TN503-3, Measurement Group Inc. Raleigh, NC (1988).Google Scholar
[18] Bickcl, P. J. and Doksurn, K. A., “Mathematical Statistics: Basic Ideas and Selected Topics”, Oakland: Holden-Day (1977).Google Scholar
[19] Clark, C. T. and Schkade, L. L., “Statistical Analysis for Administrative Decisions”, 3rd Ed., Cincinnati, South Publ. (1979).Google Scholar