Hostname: page-component-78c5997874-lj6df Total loading time: 0 Render date: 2024-11-10T11:48:29.309Z Has data issue: false hasContentIssue false
  • English
  • Français

Model Calculation of Sepiolite Surface Areas

Published online by Cambridge University Press:  28 February 2024

Toshiyuki Hibino ,
Atsumu Tsunashima ,
Atsushi Yamazaki  and
Ryohei Otsuka
Toshiyuki Hibino
Affiliation:
Materials Processing Department, National Institute for Resources and Environment, 16-3 Onogawa, Tsukuba, 305 Japan
Atsumu Tsunashima
Affiliation:
Materials Processing Department, National Institute for Resources and Environment, 16-3 Onogawa, Tsukuba, 305 Japan
Atsushi Yamazaki
Affiliation:
Department of Mineral Resources Engineering, School of Science and Engineering, Waseda University, 3-4-1 Ohkubo, Shinjyuku, 169 Japan
Ryohei Otsuka
Affiliation:
Department of Mineral Resources Engineering, School of Science and Engineering, Waseda University, 3-4-1 Ohkubo, Shinjyuku, 169 Japan
Rights & Permissions [Opens in a new window]

Abstract

Core share and HTML view are not available for this content. However, as you have access to this content, a full PDF is available via the ‘Save PDF’ action button.

In general, the N2-BET surface areas of sepiolite samples range from 95 to 400 m2/g depending on deposits.

The surface areas of five sepiolites, all varying in crystallite size, were measured on heating, and were compared with a model calculation. A sharp decrease in the surface area, due to crystal folding, was observed between 200° and 400°C. Both before and after the folding, each sepiolite sample had peculiar values. Our model sufficiently explains this difference in surface areas among the samples. In the model, which is based on the Brauner-Preisinger structural model, surface area is a function of the crystallite size and the ratios of the coverage for nitrogen adsorption on both the internal and external surfaces. These ratios of the coverage can be inversely estimated from the model. The ratios of the coverage on the internal surface are less than 0.19, and that on the external surface between 0.7 and 1.0.

Keywords

Heat treatmentModel calculationSepioliteSurface area
Type
Research Article
Information
Clays and Clay Minerals , Volume 43 , Issue 4 , August 1995 , pp. 391 - 396
Copyright
Copyright © 1995, The Clay Minerals Society

References

Brauner, K., and Preisinger, A. 1956. Struktur und Entstehung des Sepioliths. Tschermaks Miner. Petr. Mitt. 6: 120–140.CrossRefGoogle Scholar
Dandy, A. J., and Nadiye-Tabbiruka, M. S. 1975. The effect of heating in vacuo on the microporosity of sepiolite. Clays & Clay Miner. 23: 428–430.Google Scholar
Dandy, A. J., and Nadiye-Tabbiruka, M. S. 1982. Surface properties of sepiolite from Amboseli, Tanzania, and its catalytic activity for ethanol decomposition. Clays & Clay Miner. 30: 347–352.Google Scholar
Grillet, Y., Cases, J. M., Francois, M., Rouquerol, J., and Poirier, J. E. 1988. Modification of the porous structure and surface area of sepiolite under vacuum thermal treatment. Clays & Clay Miner. 36: 233–242.Google Scholar
Inagaki, S., Fukushima, Y., Doi, H., and Kamigaito, O. 1990. Pore size distribution and adsorption selectivity of sepiolite. Clay Miner. 25: 99–105.Google Scholar
Nagy, B., and Bradley, W. F. 1955. The structural scheme of sepiolite. Amer. Mineral. 40: 885–892.Google Scholar
Nishimura, Y., Hori, Y., and Takahashi, H. 1972. Structural change and adsorption character of sepiolite by heat treatment. J. Clay Sci. Soc. Japan 12: 102–108.Google Scholar
Sarikaya, Y., 1981. Effect of outgassing temperature on surface area of sepiolite. Commun. Fac. Sci. Univ. Ankara, Ser. B 27: 45–49.Google Scholar
Serna, C., Ahlrichs, J. L., and Serratosa, J. M. 1975. Folding in sepiolite crystals. Clays & Clay Miner. 23: 452–457.Google Scholar