Hostname: page-component-cd9895bd7-8ctnn Total loading time: 0 Render date: 2024-12-27T07:56:26.007Z Has data issue: false hasContentIssue false
  • English
  • Français

Six kilowatt record all-fiberized and narrow-linewidth fiber amplifier with near-diffraction-limited beam quality

Published online by Cambridge University Press:  13 June 2022

Guangjian Wang ,
Jiaxin Song Open the ORCID record for Jiaxin Song [Opens in a new window] ,
Yisha Chen ,
Shuai Ren ,
Pengfei Ma Open the ORCID record for Pengfei Ma [Opens in a new window] ,
Wei Liu Open the ORCID record for Wei Liu [Opens in a new window] ,
Tianfu Yao  and
Pu Zhou Open the ORCID record for Pu Zhou [Opens in a new window]
Guangjian Wang
Affiliation:
College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China
Jiaxin Song
Affiliation:
College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China
Yisha Chen
Affiliation:
College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China
Shuai Ren
Affiliation:
College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China
Pengfei Ma*
Affiliation:
College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China
Wei Liu
Affiliation:
College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China
Tianfu Yao
Affiliation:
College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China
Pu Zhou*
Affiliation:
College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China
*
Correspondence to: P. Ma and P. Zhou, College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China. Email: shandapengfei@126.com (P. Ma); zhoupu203@163.com (P. Zhou)
Correspondence to: P. Ma and P. Zhou, College of Advanced Interdisciplinary Studies, National University of Defense Technology, Changsha 410073, China. Email: shandapengfei@126.com (P. Ma); zhoupu203@163.com (P. Zhou)
Rights & Permissions [Opens in a new window]

Abstract

In this work, an all-fiberized and narrow-linewidth fiber amplifier with record output power and near-diffraction-limited beam quality is presented. Up to 6.12 kW fiber laser with the conversion efficiency of approximately 78.8% is achieved through the fiber amplifier based on a conventional step-index active fiber. At the maximum output power, the 3 dB spectral linewidth is approximately 0.86 nm and the beam quality factor is Mx2 = 1.43, My2 = 1.36. We have also measured and compared the output properties of the fiber amplifier employing different pumping schemes. Notably, the practical power limit of the fiber amplifier could be estimated through the maximum output powers of the fiber amplifier employing unidirectional pumping schemes. Overall, this work could provide a good reference for the optimal design and potential exploration of high-power narrow-linewidth fiber laser systems.

Keywords

fiber laserhigh powernarrow linewidth
Type
Research Article
Information
High Power Laser Science and Engineering , Volume 10 , 2022 , e22
Check for updates
Creative Commons
Creative Common License - CCCreative Common License - BY
This is an Open Access article, distributed under the terms of the Creative Commons Attribution licence (https://creativecommons.org/licenses/by/4.0/), which permits unrestricted re-use, distribution, and reproduction in any medium, provided the original work is properly cited.
Copyright
© The Author(s), 2022. Published by Cambridge University Press in association with Chinese Laser Press

1 Introduction

High-power fiber lasers are attractive laser sources in many applications, benefitting from the essential advantages of high efficiency, excellent beam quality, compact structure and convenient thermal management[Reference Richardson, Nilsson and Clarkson1–Reference Zervas and Codemard3]. Restricted by the pump brightness, stimulated Raman scattering (SRS) effect, transverse mode instability (TMI) effect, etc., monolithic fiber lasers with near-diffraction-limited beam quality have achieved over 10-kW level output in experiments[4, Reference Shiner5], and there is a theoretical power limit[Reference Dawson, Messerly, Beach, Shverdin, Stappaerts, Sridharan, Pax, Heebner, Siders and Barty6–Reference Zervas8].

The coherent beam combination and spectral beam combination provide effective approaches to breaking the limitations and further promoting the output powers of fiber lasers while maintaining excellent beam quality[Reference Fan9–Reference Liu, Ma, Su, Tao, Ma, Wang and Zhou11]. In those two beam combination systems, high-power single-mode fiber lasers with narrow-linewidth are the crucial units. Nevertheless, the power scaling of narrow-linewidth fiber lasers always lags behind that of broad-linewidth fiber lasers[Reference Ma, Xiao, Liu, Zhang, Wang, Leng and Zhou12–Reference Ma, Tao, Su, Wang, Zhou and Liu17], because extra design is required to maintain narrow-linewidth operation. Furthermore, recent experimental results reveal that narrower signal bandwidth generally means a lower TMI threshold for the same fiber amplifier[Reference Ren, Lai, Wang, Li, Song, Chen, Ma, Liu and Zhou18]. Accordingly, compared to broad-linewidth fiber amplifiers, the TMI effect is a more critical issue in designing high-power narrow-linewidth fiber amplifiers.

Extensive studies have been carried out to investigate the mechanism of the TMI effect and multiple methods are proposed to suppress the TMI effect in high-power fiber amplifiers[Reference Smith and Smith19–Reference Jauregui, Stihler and Limpert22]. The common approaches to suppressing the TMI effect in traditional step-index monolithic fiber amplifiers include shifting the pump or signal wavelength to enhance the gain saturation[Reference Hansen and Lægsgaard23], coiling the active fiber to increase the loss of higher-order modes[Reference Tao, Su, Ma, Wang and Zhou24] and optimizing the pump scheme[Reference Shi, Su, Zhang, Yang, Wang, Zhou, Xu and Lu25]. Specially designed fibers have also proved to be effective to suppress the TMI effect[Reference Otto, Klenke, Jauregui, Stutzki, Limpert and Tünnermann26–Reference Wu, Li, Xiao, Huang, Yang, Pan, Leng and Zhou29]. As for the optimization of the pump scheme, it involves adjusting the ratios of co-pump/counter-pump powers and measuring the corresponding TMI threshold of the fiber amplifier, which introduces extra load in the test of high-power fiber amplifiers.

In this paper, we report a 6 kW all-fiberized and narrow-linewidth fiber amplifier with near-diffraction-limited beam quality based on a conventional step-index active fiber. Up to 6.12 kW fiber laser is obtained with a conversion efficiency of approximately 78.8%. The stimulated Brillouin scattering (SBS), SRS and TMI effects are effectively suppressed at the maximum output power in the experiment. Furthermore, we have also measured and compared the output properties of the fiber amplifier employing different pumping schemes. The comparisons reveal that the output properties of the fiber amplifier employing unidirectional pumping schemes could provide practical guidance for the optimal design of high-power narrow-linewidth fiber amplifiers employing the bidirectional pumping scheme.

2 Experimental setup

The experimental setup of the high-power all-fiberized and narrow-linewidth fiber amplifier is shown in Figure 1. The fiber amplifier mainly consists of a phase-modulated single-frequency laser (SFL) serving as the seed laser and a bidirectional pumping Yb-doped fiber (YDF) amplifier. In the seed laser, an SFL at 1080 nm is first phase-modulated via an electro-optical modulator (EOM) driven by a white noise source (WNS) signal. The phase-modulated laser is then power amplified to about 50 W through the pre-amplifiers. A circulator is used after the pre-amplifiers to export the backward propagating laser from the main amplifier to protect the seed laser and monitor the SBS effect. A mode field adapter (MFA) with a 10/125 μm input fiber and 20/400 μm output fiber is used to connect the circulator and the main amplifier.

Figure 1 Experimental setup of the all-fiberized and narrow-linewidth fiber amplifier.

In the main amplifier, there are two sets of pump sources centering at approximately 976 nm. Each set of pump sources has six pump modules with core/cladding diameters of 220/242 μm pigtail fiber, and seven LDs with sole maximum output power of approximately 130 W and core/cladding diameters of 105/125 μm are combined by a 7×1 combiner in each module. The pump modules are injected into the conventional step-index YDF with the core/cladding diameter of 20/400 μm via two (6+1)×1 signal-pump combiners, respectively. The absorption coefficient of the YDF is approximately 1.2 dB/m at 976 nm, and the length of the YDF is approximately 14.5 m. Both ends of the YDF are coiled into a racetrack spiral shape with a minimum diameter of approximately 8.5 cm to suppress the TMI effect. Two cladding power strippers (CPSs) are used at both ends of the main amplifier to remove the residual cladding light. The main amplifier is placed on a water-cooling plate, and the final output laser is terminated through a quartz block holder (QBH).

3 Experimental results and discussion

To investigate the overall performance of the fiber amplifier, we first measure the basic output properties of the fiber amplifiers employing the forward pumping scheme and backward pumping scheme, respectively. Then, the detailed output properties of the fiber amplifier employing bidirectional pumping scheme are presented.

3.1 Output properties of the fiber amplifier employing the forward pumping scheme

Figures 2(a) and 2(b) illustrate the output power and spectral properties of the fiber amplifier employing the forward pumping scheme. As shown in Figure 2(a), the output power of the signal laser increases almost linearly with the pump power. The maximum output power is approximately 2.82 kW at the pump power of 3.69 kW, with the corresponding conversion efficiency being approximately 76.4%. In addition, there is no sign of nonlinear increase for the backward power. Thus, the SBS effect is effectively suppressed in the fiber amplifier. As shown in Figure 2(b), compared with the seed laser, the central spectrum of the signal laser at the maximum output power is nearly maintained, while the sideband of the spectrum broadens slightly. Specifically, the 3 dB spectral linewidth decreases from approximately 0.61 nm to approximately 0.33 nm, while the 20 dB spectral linewidth increases from approximately 1.58 nm to approximately 2.07 nm. In addition, the signal-to-noise ratio (SNR) exceeds 50 dB compared to the spectral component over 1100 nm, which confirms that the SRS effect is effectively suppressed in the fiber amplifier employing the forward pumping scheme. Figure 2(c) illustrates the Fourier spectrum of the signal power at the maximum output power. As shown in Figure 2(c), there is an obvious noise-like frequency distribution below 2 kHz, which indicates the occurrence of the TMI effect. Thus, further power scaling of the fiber amplifier employing the forward pumping scheme is restricted by the TMI effect.

Figure 2 Basic output properties of the fiber amplifier employing the forward pumping scheme: (a) power curve; (b) output spectrum at the maximum output power; (c) Fourier spectrum of the signal laser at the maximum output power.

3.2 Output properties of the fiber amplifier employing the backward pumping scheme

Figures 3(a) and 3(b) illustrate the output power and spectral properties of the fiber amplifier employing the backward pumping scheme. As shown in Figure 3(a), the output power of the signal laser also increases almost linearly with the pump power. The maximum output power is approximately 3.62 kW at the pump power of 4.50 kW with the corresponding conversion efficiency being approximately 80.4%, and the SBS effect is also effectively suppressed in the fiber amplifier. As shown in Figure 3(b), the overall change of the signal laser at the maximum output power is similar to that shown in Figure 2(b). Specifically, the 3 and 20 dB spectral linewidths of the signal laser at the maximum output power are about 0.55 and 1.62 nm, respectively. In addition, the SNR also exceeds 50 dB compared to the spectral component over 1100 nm, which confirms that the SRS effect is also effectively suppressed in the fiber amplifier employing the backward pumping scheme. Figure 3(c) illustrates the Fourier spectrum of the signal laser at the maximum output power. As shown in Figure 3(c), there is obvious noise-like frequency distribution or peaks between 2 and 6 kHz, which indicates the occurrence of the TMI effect. Thus, further power scaling of the fiber amplifier employing the backward pumping scheme is also restricted by the TMI effect.

Figure 3 Basic output properties of the fiber amplifier employing the backward pumping scheme: (a) power curve; (b) output spectrum at the maximum output power; (c) Fourier spectrum of the signal laser at the maximum output power.

3.3 Output properties of the fiber amplifier employing the bidirectional pumping scheme

Figures 4(a) and 4(b) illustrate the output power and spectral properties of the fiber amplifier employing the bidirectional pumping scheme. As shown in Figure 4(a), the maximum output power of the signal laser could reach approximately 6.12 kW at the pump power of 7.77 kW (3.17 kW forward pump and 4.60 kW backward pump) with the corresponding conversion efficiency of approximately 78.8%, and the SBS effect is also effectively suppressed in the fiber amplifier employing the bidirectional pumping scheme. As shown in Figure 4(b), the overall changes of the output spectra near 1080 nm are similar to the results shown in Figures 2(b) and 3(b). Specifically, the 3 and 20 dB spectral linewidths of the signal laser at the maximum output power are about 0.86 and 3.98 nm, respectively. In addition, the emergence of the Raman Stokes light around 1136 nm is observed at the output power of 3.59 kW, and the intensity of the Raman Stokes light grows gradually with the increasing output power. The minimum SNR compared to the spectral component of the Raman Stokes light decreases to approximately 35.7 dB at the output power of 6.12 kW, which indicates that further power scaling of the fiber amplifier employing the bidirectional pumping scheme could be restricted by the SRS effect.

Figure 4 Basic output properties of the fiber amplifier employing the bidirectional pumping scheme: (a) power curve; (b) output spectra.

We have also measured the Fourier spectrum and the beam quality of the signal laser at the maximum output power in the fiber amplifier employing the bidirectional pumping scheme. As shown in Figure 5(a), there is no obvious noise-like frequency distribution or peaks in the Fourier spectrum, which indicates that this fiber amplifier still operates below the TMI effect at the maximum output power. The beam quality of the output laser is measured by a beam quality analyzer. As shown in Figure 5(b), the beam quality factor is measured to be M x2 = 1.43, M y2 = 1.36 at the output power of 6.12 kW, which shows that near-diffraction-limited beam quality has been achieved, and the TMI effect has been suppressed effectively. Compared with the beam quality (M x2 = 1.38, M y2 = 1.28) of the injected laser passing through the main amplifier, the beam quality is degraded a little in the power scaling process, which may be attributed to the mode distortion caused by the increased temperature of the backward pump and signal combiner in the experiment.

Figure 5 Output properties of the signal laser at the maximum output power in the fiber amplifier employing the bidirectional pumping scheme: (a) Fourier spectrum; (b) beam quality factor (the insert figure is beam profile at the location of Z = 393.5 mm).

3.4 Comparisons among the fiber amplifier employing different pumping schemes

Comparing the maximum output powers of the same fiber amplifier employing different pumping schemes, we find a simple relationship among the three output powers. Specifically, the maximum output power (~6.12 kW) of the fiber amplifier employing the bidirectional pumping scheme is close (~95%) to the sum of the maximum output powers of the fiber amplifier employing unidirectional pumping schemes (~2.82 and ~3.62 kW). In addition, the maximum injected backward pump power in the bidirectional pumping scheme is also close to that in the backward pumping scheme. Those two results could introduce two practical guidance in the design of high-power narrow-linewidth fiber amplifiers employing the bidirectional pumping scheme, when power scaling of the unidirectional pumping schemes is restricted by the TMI effect. Firstly, the practical power limit of a high-power narrow-linewidth fiber amplifier might be estimated through measuring the TMI effect of the fiber amplifier employing unidirectional pumping schemes. Secondly, the maximum launched backward pump power in the bidirectional pumping scheme could be obtained through the maximum injected pump power in the backward pumping scheme. Therefore, the output properties of the fiber amplifier employing unidirectional pumping schemes could provide practical guidance for the optimal design and potential exploration of high-power narrow-linewidth fiber amplifiers employing the bidirectional pumping scheme.

We might notice the obvious difference among the 3 dB spectral linewidth of the signal laser at the corresponding maximum output power in the three pumping schemes. To further reveal the difference, we have measured and calculated the 3 dB spectral linewidth of the signal laser at different output powers in the three pumping schemes. As shown in Figure 6, the overall changes for 3 dB spectral linewidth are irregular in the three cases. In particular, the 3 dB spectral linewidth ranges from approximately 0.41 nm to approximately 0.86 nm when the output power is over 4.5 kW. Thus, the 3 dB spectral linewidth might not be appropriate to characterize the spectral performance of high-power narrow-linewidth fiber amplifiers. For further consideration of the spectral wing broadening phenomenon, it might be useful to characterize the spectral purity of high-power narrow-linewidth fiber amplifiers through the 20 dB spectral linewidth or the power-ratio spectral linewidth[Reference Liu, Song, Ma, Xiao and Zhou30].

Figure 6 The 3 dB spectral linewidths of the signal laser at different output powers.

4 Conclusion

In this work, a more than 6 kW narrow-linewidth fiber laser with near-diffraction-limited beam quality has been reported based on a conventional all-fiberized YDF amplifier. Up to 6.12 kW fiber laser is achieved at a total pump power of 7.77 kW (3.17 kW forward pump and 4.6 kW backward pump) with the corresponding conversion efficiency of approximately 78.8%. At the maximum output power, the 3 dB spectral linewidth is approximately 0.86 nm, and the beam quality factor is M x2 = 1.43, M y2 = 1.36. To the best of our knowledge, this is the highest power ever reported in narrow-linewidth fiber lasers with near-diffraction-limited beam quality. Further comparisons among the fiber amplifier employing different pumping schemes indicate that the practical power limit of a high-power narrow-linewidth fiber amplifier could be close to the sum of the maximum output powers of the same fiber amplifier employing unidirectional pumping schemes. Overall, this work could provide a good reference for the optimal design and potential exploration of high-power narrow-linewidth fiber laser systems.

Acknowledgment

This work was supported by National Natural Science Foundation of China (NSFC) (62005313, 62035015) and Innovative Research Team in Natural Science Foundation of Hunan Province (2019JJ10005).

Footnotes

†

These authors contributed equally to this paper.

References

Richardson, D. J., Nilsson, J., and Clarkson, W. A., J. Opt. Soc. Am. B 27, B63 (2010).CrossRefGoogle Scholar
Shi, W., Fang, Q., Zhu, X., Norwood, R. A., and Peyghambarian, N., Appl. Opt. 53, 6554 (2014).CrossRefGoogle Scholar
Zervas, M. N. and Codemard, C. A., IEEE J. Sel. Top. Quantum Electron. 20, 219 (2014).CrossRefGoogle Scholar
IPG Photonics Corporation, “IPG photonics successfully tests world’s first 10 kilowatt single-mode production laser,” http://www.ipgphotonics.com (2009).Google Scholar
Shiner, B., “The impact of fiber laser technology on the world wide material processing market,” in CLEO: Applications and Technology (Optica Publishing Group, 2013), paper AF2J.1.Google Scholar
Dawson, J. W., Messerly, M. J., Beach, R. J., Shverdin, M. Y., Stappaerts, E. A., Sridharan, A. K., Pax, P. H., Heebner, J. E., Siders, C. W., and Barty, C. P. J., Opt. Express 16, 13240 (2008).CrossRefGoogle Scholar
Zhu, J., Zhou, P., Ma, Y., Xu, X., and Liu, Z., Opt. Express 19, 18645 (2011).CrossRefGoogle Scholar
Zervas, M. N., Opt. Express 27, 19019 (2019).CrossRefGoogle Scholar
Fan, T. Y., IEEE J. Sel. Top. Quantum Electron. 11, 567 (2005).CrossRefGoogle Scholar
Zheng, Y., Yang, Y., Wang, J., Hu, M., Liu, G., Zhao, X., Chen, X., Liu, K., Zhao, C., He, B., and Zhou, J., Opt. Express 24, 12063 (2016).CrossRefGoogle Scholar
Liu, Z., Ma, P., Su, R., Tao, R., Ma, Y., Wang, X., and Zhou, P., J. Opt. Soc. Am. B 34, A7 (2016).CrossRefGoogle Scholar
Ma, P., Xiao, H., Liu, W., Zhang, H., Wang, X., Leng, J., and Zhou, P., High Power Laser Sci. Eng. 9, e45 (2021).CrossRefGoogle Scholar
Huang, Z.-M., Shu, Q., Tao, R.-M., Chu, Q.-H., Luo, Y., Yan, D.-L., Feng, X., Liu, Y., Wu, W.-J., Zhang, H.-Y., Lin, H.-H., Wang, J.-J., and Jing, F., IEEE Photonics Technol. Lett. 33, 1181 (2021).CrossRefGoogle Scholar
Yu, C. X., Shatrovoy, O., Fan, T. Y., and Taunay, T. F., Opt. Lett. 41, 5202 (2016).CrossRefGoogle Scholar
Xu, Y., Fang, Q., Qin, Y., Meng, X., and Shi, W., Appl. Opt. 54, 9419 (2015).CrossRefGoogle Scholar
Shen, H., Lou, Q., Quan, Z., Li, X., Yang, Y., Chen, X., Li, Q., Bai, G., Qi, Y., He, B., and Zhou, J., Appl. Opt. 58, 3053 (2019).CrossRefGoogle Scholar
Ma, P., Tao, R., Su, R., Wang, X., Zhou, P., and Liu, Z., Opt. Express 24, 4187 (2016).CrossRefGoogle Scholar
Ren, S., Lai, W., Wang, G., Li, W., Song, J., Chen, Y., Ma, P., Liu, W., and Zhou, P., Opt. Express 30, 7845 (2022).CrossRefGoogle Scholar
Smith, A. V. and Smith, J. J., Opt. Express 19, 10180 (2011).CrossRefGoogle Scholar
Ward, B., Robin, C., and Dajani, I., Opt. Express 20, 11407 (2012).CrossRefGoogle Scholar
Tao, R., Wang, X., and Zhou, P., IEEE J. Sel. Top. Quantum Electron. 24, 0903319 (2018).CrossRefGoogle Scholar
Jauregui, C., Stihler, C., and Limpert, J., Adv. Opt. Photonics 12, 429 (2020).CrossRefGoogle Scholar
Hansen, K. R. and Lægsgaard, J., Opt. Express 22, 11267 (2014).CrossRefGoogle Scholar
Tao, R., Su, R., Ma, P., Wang, X., and Zhou, P., Laser Phys. Lett. 14, 025101 (2017).CrossRefGoogle Scholar
Shi, C., Su, R. T., Zhang, H. W., Yang, B. L., Wang, X. L., Zhou, P., Xu, X. J., and Lu, Q. S., IEEE Photonics J. 9, 1502910 (2017).Google Scholar
Otto, H.-J., Klenke, A., Jauregui, C., Stutzki, F., Limpert, J., and Tünnermann, A., Opt. Lett. 39, 2680 (2014).CrossRefGoogle Scholar
Zhang, Z., Lin, X., Chen, G., Liao, L., Xing, Y., Li, H., Peng, J., Dai, N., and Li, J., IEEE Photonics J. 13, 1501006 (2021).Google Scholar
Xia, N. and Yoo, S., J. Lightwave Technol. 38, 4478 (2020).CrossRefGoogle Scholar
Wu, H., Li, R., Xiao, H., Huang, L., Yang, H., Pan, Z., Leng, J., and Zhou, P., Opt. Express 29, 31337 (2021).CrossRefGoogle Scholar
Liu, W., Song, J., Ma, P., Xiao, H., and Zhou, P., Photonics Res. 9, 424 (2021).CrossRefGoogle Scholar
Figure 0

Figure 1 Experimental setup of the all-fiberized and narrow-linewidth fiber amplifier.

Figure 1

Figure 2 Basic output properties of the fiber amplifier employing the forward pumping scheme: (a) power curve; (b) output spectrum at the maximum output power; (c) Fourier spectrum of the signal laser at the maximum output power.

Figure 2

Figure 3 Basic output properties of the fiber amplifier employing the backward pumping scheme: (a) power curve; (b) output spectrum at the maximum output power; (c) Fourier spectrum of the signal laser at the maximum output power.

Figure 3

Figure 4 Basic output properties of the fiber amplifier employing the bidirectional pumping scheme: (a) power curve; (b) output spectra.

Figure 4

Figure 5 Output properties of the signal laser at the maximum output power in the fiber amplifier employing the bidirectional pumping scheme: (a) Fourier spectrum; (b) beam quality factor (the insert figure is beam profile at the location of Z = 393.5 mm).

Figure 5

Figure 6 The 3 dB spectral linewidths of the signal laser at different output powers.