Hostname: page-component-cd9895bd7-hc48f Total loading time: 0 Render date: 2024-12-28T01:11:23.840Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructure and tribology of laser mixed Fe/Ti/C multilayered films on AISI 304 stainless steel

Published online by Cambridge University Press:  31 January 2011

M. Nastasi ,
J-P. Hirvonen ,
T. G. Zocco  and
T. R. Jervis
M. Nastasi
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545
J-P. Hirvonen
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545
T. G. Zocco
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545
T. R. Jervis
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545
Get access

Abstract

An excimer laser was used to mix Fe/Ti/C multilayered films on 304 stainless steel substrates. The samples were processed at both 1.1 and 1.7 J/cm2 with the number of pulses at each position varied between 1 and 10. Composition, microstructure, phase evolution, and tribological properties were observed to correlate with total laser fluence. Increases in Fe concentration from substrate interdiffusion and loss of C content were observed with increasing total laser fluence. The best tribological properties were observed in films possessing a combination of an amorphous or Fe3C phase plus fine grain TiC following processing at low and intermediate total laser fluence. At higher total fluences a combination of α-Fe, Fe3C, and fine-grain TiC was observed along with degradation in the wear and friction properties. Under optimum laser processing conditions the modified surface had a friction coefficient under dry sliding conditions reduced by a factor of 2 relative to uncoated 304 stainless steel and was significantly more wear resistant. These improvements in wear and friction appear to be related to the reduced chemical reactivity of the amorphous and carbide phases and to the influence of microstructure on improved mechanical properties.

Type
Articles
Information
Journal of Materials Research , Volume 5 , Issue 6 , June 1990 , pp. 1207 - 1214
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Singer, I. L. and Jeffries, R. A., Appl. Phys. Lett. 43, 925 (1983).CrossRefGoogle Scholar
2Follstaedt, D.M., Knapp, J.A., Pope, L.E., Yost, F.G., and Picraux, S.T., Appl. Phys. Lett. 45, 529 (1984).CrossRefGoogle Scholar
3Pethica, J. B., Hutchins, R., and Oliver, W. C., Nucl. Instrum. Methods 209/210, 995 (1983).Google Scholar
4Hirvonen, J-P., Nastasi, M., Phillips, J.R., and Mayer, J.W., J. Vac. Sci. Technol. A4, 2997 (1986).Google Scholar
5Hirvonen, J-P., Nastasi, M., and Mayer, J.W., in Materials Modification and Growth Using Ion Beams, edited by Gibson, U. J., White, A. E., and Pronko, P. P. (Materials Research Society, Pittsburgh, PA, 1987), p. 335.Google Scholar
6Hirvonen, J-P., Nastasi, M., and Mayer, J.W., J. Appl. Phys. 60, 980 (1986).CrossRefGoogle Scholar
7Hirvonen, J-P., Nastasi, M., and Mayer, J.W., Nucl. Instrum. Methods B13, 479 (1986).CrossRefGoogle Scholar
8Nastasi, M., Hirvonen, J-P., Caro, M., Rimini, E., and Mayer, J.W., Appl. Phys. Lett. 50, 177 (1987).Google Scholar
9Malvezzi, A. M., Bloembergen, N., and Huang, C.Y., Phys. Rev. Lett. 57, 146 (1986).CrossRefGoogle Scholar
10Follstaedt, D.M., Knapp, J.A., and Peercy, P.S., J. of Non-Cryst. Solids, 61 &62, 451 (1984).CrossRefGoogle Scholar
11Hirvonen, J-P., Nastasi, M., Phillips, J. R., and Mayer, J.W., J. Vac. Sci. Tech. A4, 2997 (1986).Google Scholar
12Jervis, T. R., Hirvonen, J-P., and Nastasi, M., J. Mater. Res. 3 (6), 1104 (1988).Google Scholar
13Jervis, T. R., Hirvonen, J-P., Nastasi, M., Zocco, T. G., Martin, J. A., Pharr, G. M., and Oliver, W. C., in New Materials Approaches to Tribology: Theory and Applications, edited by Pope, L.E., Fehrenbacher, L.L., and Winer, W. O. (Materials Research Society, Pittsburgh, PA, 1989), p. 189.Google Scholar
14Gerkema, J. and Miedema, A. R., Surf. Sci. 124, 351 (1983).Google Scholar
15Buckley, D. H., Surface Effects in Adhesion, Friction, Wear, and Lubrication (Elsevier Scientific Publishing Company, Amsterdam, 1981), Chaps. 4–7.Google Scholar
16Dieter, G. E., in Mechanical Metallurgy (McGraw-Hill, New York, 1976), 2nd ed., Chap. 9.Google Scholar
17Barrett, C. R., Nix, W. D., and Tetelman, A. S., in The Principles of Engineering Materials (Prentice-Hall, Inc., Englewood Cliffs, NJ, 1973), Chap. 8.Google Scholar