Hostname: page-component-cd9895bd7-q99xh Total loading time: 0 Render date: 2024-12-27T14:07:33.605Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical properties and tensile fracture of Ti–Al–V alloy strip under electropulsing-induced phase change

Published online by Cambridge University Press:  15 December 2014

Xiaoxin Ye ,
Zion T.H. Tse  and
Guoyi Tang
Xiaoxin Ye*
Affiliation:
Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055, People's Republic of China; and Key Laboratory for Advanced Materials of Ministry of Education, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084, People's Republic of China
Zion T.H. Tse
Affiliation:
College of Engineering, The University of Georgia, Athens, Georgia 30602, USA
Guoyi Tang*
Affiliation:
Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055, People's Republic of China; and Key Laboratory for Advanced Materials of Ministry of Education, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084, People's Republic of China
*
a)Address all correspondence to this author. e-mail: guoyitangforwork@163.com
Get access

Abstract

The effect of high-energy electropulsing treatment (EPT) on the microstructure evolution, mechanical properties, and fracture behavior of as-treated Ti–6Al–4V alloy strips was investigated. EPT was found to accelerate phase transition and microstructure evolution of quasi-single-phase titanium alloy strips at a relatively low temperature, and obtain characteristic duplex microstructure and Widmanstatten microstructure. The EPT-induced microstructural changes increased elongation-to-failure remarkably with a slight decrease in tensile strength. Fracture surface observation and three-dimensional analysis showed that transition from small-shallow dimple colony to big-deep colony fracture took place with an increase in frequency of EPT. The rapid phase change of the Ti–6Al–4V alloy strip under EPT was attributed to the enhancement of nucleation rate and atomic diffusion resulting from the coupling of the thermal and athermal effects. It is supposed that EPT can provide a highly efficient method for the intermediate-softening annealing of titanium alloy sheet/strips.

Keywords

titanium alloyelectropulsing treatmentphase changemicrostructure evolutionmechanical propertiesfracture behavior
Type
Articles
Information
Journal of Materials Research , Volume 30 , Issue 2 , 28 January 2015 , pp. 206 - 223
Copyright
Copyright © Materials Research Society 2015 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Bermingham, M.J., McDonald, S.D., StJohn, D.H., and Dargusch, M.S.: Segregation and grain refinement in cast titanium alloys. J. Mater. Res. 24, 1529 (2009).CrossRefGoogle Scholar
Lewis, A.C., Qidwai, S.M., Rowenhorst, D.J., and Geltmacher, A.B.: Correlation between crystallographic orientation and mechanical response in a three-dimensional beta-Ti microstructure. J. Mater. Res. 26, 957 (2011).CrossRefGoogle Scholar
Gurao, N.P., Sethuraman, S., and Suwas, S.: Evolution of texture and microstructure in commercially pure titanium with change in strain path during rolling. Metall. Mater. Trans. A 44, 1497 (2013).CrossRefGoogle Scholar
Nakai, M., Niinomi, M., Hieda, J., Cho, K., Nagasawa, Y., Konno, T., Ito, Y., Itsumi, Y., and Oyama, H.: Reduction in anisotropy of mechanical properties of coilable (alpha plus beta)-type titanium alloy thin sheet through simple heat treatment for use in next-generation aircraft applications. Mater. Sci. Eng., A 594, 103 (2014).CrossRefGoogle Scholar
Liu, C.M., Wang, H.M., Tian, X.J., and Tang, H.B.: Subtransus triplex heat treatment of laser melting deposited Ti-5Al-5Mo-5V-1Cr-1Fe near beta titanium alloy. Mater. Sci. Eng., A 590, 30 (2014).CrossRefGoogle Scholar
Buffa, G., Ducato, A., and Fratini, L.: FEM based prediction of phase transformations during friction stir welding of Ti6Al4V titanium alloy. Mater. Sci. Eng., A 581, 56 (2013).CrossRefGoogle Scholar
Yao, Z.K., Guo, H.Z., Yang, C., Guo, Y.G., and Su, M.Y.: Effects of the interaction of deformation and phase change on microstructure and mechanical properties of Ti-17 alloy. Rare Metal Mater. Eng. 32, 538 (2003).Google Scholar
Yan, M., Dargusch, M.S., Ebel, T., and Qian, M.: A transmission electron microscopy and three-dimensional atom probe study of the oxygen-induced fine microstructural features in as-sintered Ti-6Al-4V and their impacts on ductility. Acta Mater. 68, 196 (2014).CrossRefGoogle Scholar
Huang, R.T., Huang, W.L., Huang, R.H., and Tsay, L.W.: Effects of microstructures on the notch tensile fracture feature of heat-treated Ti-6Al-6V-2Sn alloy. Mater. Sci. Eng., A 595, 297 (2014).CrossRefGoogle Scholar
Okutani, T., Kabeya, Y., and Nagai, H.: Thermoelectric n-type silicon germanium synthesized by unidirectional solidification in microgravity. J. Alloys Compd. 551, 607 (2013).CrossRefGoogle Scholar
Gromov, V.E., Gurevich, L.I., Kurilov, V.F., and Erilova, T.V.: Influence of current pulses on the mobility and multiplication of dislocations in Zn. Strength Mater. 21, 1335 (1989).CrossRefGoogle Scholar
Gromov, V.E., Gorbunov, S.V., Ivanov, Y.F., Vorobiev, S.V., and Konovalov, S.V.: Formation of surface gradient structural-phase states under electron-beam treatment of stainless steel. J. Surf. Invest.: X-Ray, Synchrotron Neutron Tech. 5, 974 (2011).CrossRefGoogle Scholar
Konovalov, S.V., Atroshkina, A.A., Ivanov, Y.F., and Gromov, V.E.: Evolution of dislocation substructures in fatigue loaded and failed stainless steel with the intermediate electropulsing treatment. Mater. Sci. Eng., A 527, 3040 (2010).CrossRefGoogle Scholar
Zhu, Y.H., To, S., Lee, W., Liu, X.M., Jiang, Y.B., and Tang, G.Y.: Electropulsing-induced phase transformations in a Zn-Al-based alloy. J. Mater. Res. 24, 2661 (2009).CrossRefGoogle Scholar
Jiang, Y.B., Tang, G.Y., Shek, C., Zhu, Y.H., and Xu, Z.H.: On the thermodynamics and kinetics of electropulsing induced dissolution of beta-Mg17Al12 phase in an aged Mg-9Al-1Zn alloy. Acta Mater. 57, 4797 (2009).CrossRefGoogle Scholar
Ye, X., Kuang, J., Li, X., and Tang, G.: Microstructure, properties and temperature evolution of electro-pulsing treated functionally graded Ti–6Al–4V alloy strip. J. Alloys Compd. 599, 1 (2014).CrossRefGoogle Scholar
Ye, X., Tang, G., Song, G., and Kuang, J.: Effect of electropulsing treatment on the microstructure, texture, and mechanical properties of cold-rolled Ti–6Al–4V alloy. J. Mater. Res. 29, 1500 (2014).CrossRefGoogle Scholar
Ye, X., Li, X., Song, G., and Tang, G.: Effect of recovering damage and improving microstructure in the titanium alloy strip under high-energy electropulses. J. Alloys Compd. 616, 173 (2014).CrossRefGoogle Scholar
Ye, X., Yang, Y., Song, G., and Tang, G.: Enhancement of ductility, weakening of anisotropy behavior and local recrystallization in cold-rolled Ti-6Al-4V alloy strips by high-density electropulsing treatment. Appl. Phys. A (2014). doi:10.1007/s00339-014-8655-1.CrossRefGoogle Scholar
Ye, X., Yang, Y., and Tang, G.: Microhardness and corrosion behavior of surface gradient oxide coating on the titanium alloy strips under high energy electro-pulsing treatment. Surf. Coat. Technol. 258, 467–484 (2014). doi:10.1016/j.surfcoat.2014.08.052.CrossRefGoogle Scholar
Xiaoxin, Y. and Guoyi, T.: Effect of coupling asynchronous acoustoelectric effects on the corrosion behavior, microhardness and biocompatibility of biomedical titanium alloy strips. J. Mater. Sci.: Mater. Med. (2014). JMSM-D-14-00030R1.Google Scholar
Ye, X., Ye, Y., and Tang, G.: Effect of electropulsing treatment and ultrasonic striking treatment on the mechanical properties and microstructure of biomedical Ti-6Al-4V alloy. J. Mech. Behav. Biomed. Mater. 40, 287 (2014).CrossRefGoogle ScholarPubMed
Ye, X., Liu, T., Ye, Y., Wang, H., Tang, G., and Song, G.: Enhanced grain refinement and microhardness of Ti–Al–V alloy by electropulsing ultrasonic shock. J. Alloys Compd. 621, 66–70 (2015). doi:10.1016/j.jallcom.2014.09.192.CrossRefGoogle Scholar
Jiang, J.F., Wang, Y., and Qu, J.J.: Microstructure and mechanical properties of AZ61 alloys with large cross-sectional size fabricated by multi-pass ECAP. Mater. Sci. Eng., A 560, 473 (2013).CrossRefGoogle Scholar
Shi, B.Q., Chen, R.S., and Ke, W.: Solid solution strengthening in polycrystals of Mg-Sn binary alloys. J. Alloys Compd. 509, 3357 (2011).CrossRefGoogle Scholar
Li, C.L., Mi, X.J., Ye, W.J., Hui, S.X., Yu, Y., and Wang, W.Q.: A study on the microstructures and tensile properties of new beta high strength titanium alloy. J. Alloys Compd. 550, 23 (2013).CrossRefGoogle Scholar
Knipling, K.E. and Fonda, R.W.: Microstructural evolution in Ti-5111 friction stir welds. Metall. Mater. Trans. A 42, 2312 (2011).CrossRefGoogle Scholar
Shao, H., Zhao, Y.Q., Ge, P., and Zeng, W.D.: Crack initiation and mechanical properties of TC21 titanium alloy with equiaxed microstructure. Mater. Sci. Eng., A 586, 215 (2013).CrossRefGoogle Scholar
Xu, Z.H., Tang, G.Y., Tian, S.Q., Ding, F., and Tian, H.Y.: Research of electroplastic rolling of AZ31 Mg alloy strip. J. Mater. Process. Technol. 182, 128 (2007).CrossRefGoogle Scholar
Haoming, L., Guoyi, T., Yanbin, J., Qing, X., Shiding, S., and Jianan, L.: Effect of thermo-electropulsing rolling on mechanical properties and microstructure of AZ31 magnesium alloy. Mater. Sci. Eng., A 529, 138 (2011).Google Scholar
Zhu, Y.H., To, S., Lee, W.B., Liu, X.M., Jiang, Y.B., and Tang, G.Y.: Effects of dynamic electropulsing on microstructure and elongation of a Zn-Al alloy. Mater. Sci. Eng., A 501, 125 (2009).CrossRefGoogle Scholar
Zhou, T.H., Zurob, H.S., Essadiqi, E., and Voyzelle, B.: Kinetics of delta-ferrite to austenite phase transformation in a two-phase Fe-Al-C alloy. Metall. Mater. Trans. A 42, 3349 (2011).CrossRefGoogle Scholar
Tanimura, M. and Koyama, Y.: Diffusion blocking, path variability, and bifurcation of the final state in the phase separation of Ni-3(Al,V)(1-delta) alloys. Phys. Rev. B 76, 126–130 (2007).CrossRefGoogle Scholar
Zhu, R.F., Tang, G.Y., Shi, S.Q., and Fu, M.W.: Effect of electroplastic rolling on deformability and oxidation of NiTiNb shape memory alloy. J. Mater. Process. Technol. 213, 30 (2013).CrossRefGoogle Scholar
Cao, H., Min, J.Y., Wu, S.D., Xian, A.P., and Shang, J.K.: Pinning of grain boundaries by second phase particles in equal-channel angularly pressed Cu-Fe-P alloy. Mater. Sci. Eng., A 431, 86 (2006).CrossRefGoogle Scholar
Li, J.Y., Liu, J.Y., Jin, M.J., and Jin, X.J.: Grain size dependent phase stability of pulse electrodeposited nano-grained Co-Ni films. J. Alloys Compd. 5771, S151 (2013).CrossRefGoogle Scholar