Hostname: page-component-cd9895bd7-gvvz8 Total loading time: 0 Render date: 2024-12-28T03:45:32.848Z Has data issue: false hasContentIssue false
  • English
  • Français

A Multi-Step Transmission Electron Microscopy Sample Preparation Technique for Cracked, Heavily Damaged, Brittle Materials

Published online by Cambridge University Press:  07 October 2014

Claire V. Weiss Brennan ,
Scott D. Walck  and
Jeffrey J. Swab
Claire V. Weiss Brennan*
Affiliation:
U.S. Army Research Laboratory, Weapons and Materials Research Directorate, Ceramics and Transparent Materials Branch, RDRL-WMM-E, 4600 Deer Creek Loop, Aberdeen Proving Ground, MD 21005, USA
Scott D. Walck
Affiliation:
U.S. Army Research Laboratory, Weapons and Materials Research Directorate, Coatings, Corrosion, and Engineered Polymers Branch,TKC Global, RDRL-WMM-C, 4600 Deer Creek Loop, Aberdeen Proving Ground, MD 21005, USA
Jeffrey J. Swab
Affiliation:
U.S. Army Research Laboratory, Weapons and Materials Research Directorate, Ceramics and Transparent Materials Branch, RDRL-WMM-E, 4600 Deer Creek Loop, Aberdeen Proving Ground, MD 21005, USA
*
*Corresponding author.claire.v.brennan.civ@mail.mil
Get access

Abstract

A new technique for the preparation of heavily cracked, heavily damaged, brittle materials for examination in a transmission electron microscope (TEM) is described in detail. In this study, cross-sectional TEM samples were prepared from indented silicon carbide (SiC) bulk ceramics, although this technique could also be applied to other brittle and/or multiphase materials. During TEM sample preparation, milling-induced damage must be minimized, since in studying deformation mechanisms, it would be difficult to distinguish deformation-induced cracking from cracking occurring due to the sample preparation. The samples were prepared using a site-specific, two-step ion milling sequence accompanied by epoxy vacuum infiltration into the cracks. This technique allows the heavily cracked, brittle ceramic material to stay intact during sample preparation and also helps preserve the true microstructure of the cracked area underneath the indent. Some preliminary TEM results are given and discussed in regards to deformation studies in ceramic materials. This sample preparation technique could be applied to other cracked and/or heavily damaged materials, including geological materials, archaeological materials, fatigued materials, and corrosion samples.

Keywords

transmission electron microscopysample preparationcracked materialsbrittle materialsceramics
Type
Technology and Software Development
Information
Microscopy and Microanalysis , Volume 20 , Issue 6 , December 2014 , pp. 1646 - 1653
Copyright
© Microscopy Society of America 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Anderson, R. & Klepis, S.J. (1997). Combined tripod polishing and fib method for preparing semiconductor plan view specimens. Mat Res Soc Symp Proc 480, 187–192.CrossRefGoogle Scholar
ASTM Standard C1326 (2013). Standard test method for Knoop indentation hardness of advanced ceramics. In Annual Book of ASTM Standards, Vol. 15.01 . West Conshohocken, PA, USA: ASTM International.Google Scholar
Claverie, A. (2013). Transmission Electron Microscopy in Micro-Nanoelectronics. Hoboken, NJ, USA: John Wiley & Sons, Incorporated.Google Scholar
Ghosh, D., Subhash, G. & Bourne, G.R. (2009). Inelastic deformation under indentation and scratch loads in a ZrB2-SiC composite. J Eur Ceram Soc 29, 3053–3061.CrossRefGoogle Scholar
Nielsen, J.K. & Maiboe, J. (2000). Epofix and vacuum: an easy method to make casts of hard substrates. Palaeontol Electron 3, 1–10.Google Scholar
Vaidyanathan, R., Dao, M., Ravichandran, G. & Suresh, S. (2001). Study of mechanical deformation in bulk metallic glass through instrumented indentation. Acta Mater 49, 3781–3789.CrossRefGoogle Scholar
Vander Voort, G.F. (1999). Metallography: Principles and Practice. Materials Park, OH, USA: ASM International.Google Scholar