Hostname: page-component-78c5997874-dh8gc Total loading time: 0 Render date: 2024-11-10T08:58:15.989Z Has data issue: false hasContentIssue false
  • English
  • Français

Fracture Energy Optimization in Synthetic Fiber Reinforced Cementitious Composites

Published online by Cambridge University Press:  16 February 2011

Victor C. Li ,
Youjiang Wang  and
Stanley Backer
Victor C. Li
Affiliation:
Advanced Civil Engineering Materials Research Laboratory, Department of Civil Engineering, University of Michigan, Ann Arbor, MI 48109
Youjiang Wang
Affiliation:
School of Textile & Fiber Engineering, Georgia Institute of Technology, Atlanta, GA 30332
Stanley Backer
Affiliation:
Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA 02139
Get access

Abstract

A study has been carried out on cementitious composites reinforced with various synthetic fibers, focusing on their tensile behavior, toughness, and fracture mechanisms. A model is formulated to predict the tensile behavior and fracture energy of fiber reinforced cementitious composites (FRC) with short, randomly distributed fibers. The model accounts for the pull-out of fibers oblique to the fracture surfaces (including snubbing friction effect), and the variation of the fiber/matrix interfacial shear stress during pull-out. Experimental and analytical results are shown to be in close agreement for the one class of fiber reinforcement which best satisfies the assumptions of the model. Systems which violate the assumptions exhibited different failure mechanisms and were observed to show less satisfactory reinforcement performance, especially the composite fracture energy. The model is used to examine the effect of fiber properties on composite post-cracking behavior and is useful in design of such material systems with optimum performance and cost effectiveness.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 211: Symposium O – Fiber-Reinforced Cementitious Materials , 1990 , 63
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Wang, Y., “Mechanics of Fiber Reinforced Cementitious Composites”, Ph.D. Thesis, Department of Mechanical Engineering, Massachusetts Institute of Technology (June 1989).Google Scholar
[2] Wang, Y., Li, V.C., and Backer, S., “Tensile Properties of Synthetic Fiber Reinforced Mortar”, Journal of Cement and Concrete Composites, Vol.12, No.1 (1990) pp. 29–40.Google Scholar
[3] Li, V.C., Wang, Y., and Backer, S., “A Statistical-Micromechanical Model of Tension-Softening Behavior of Short Fiber Reinforced Brittle Matrix Composites”, Journal of Mechanics and Physics of Solids, in press (1991).Google Scholar
[4] Wang, Y., Li, V.C.,and Backer, S., “Tensile Failure Mechanisms in Synthetic Fiber Reinforced Mortar” Journal of Materials Science, in press (1991).Google Scholar
[5] Li, V.C., Wang, Y., and Backer, S., “Effect of Inclining Angle, Bundling, and Surface Treatment on Synthetic Fiber Pull-out from a Cement Matrix”, Composites Vol.21, No. 2 (1990) pp. 132–140.Google Scholar
[6] Wang, Y., Li, V.C., and Backer, S., “Modeling of Fiber Pull-Out from a CementMatrix”, International Journal of Cement Composites and Lightweight Concrete Vol.10, No. 3 (1988) pp. 143–149.CrossRefGoogle Scholar
[7] Wang, Y., Li, V.C., and Backer, S., “Experimental Determination of Tensile Behavior of Fiber Reinforced Concrete”, ACI Materials Journal Vol.87, No. 5 (1990) pp. 461–468.Google Scholar
[8] Li, V.C., “Post-Crack Scaling Relations for Fiber Reinforced Cementitious Composites”, ASCE Journal of Materials in Civil Engineering, in press (1991).Google Scholar
[19] Aveston, J., Cooper, G.A., and Kelly, A., “Single and Multiple Fracture”, in The Properties of Fiber Composites (IPC Science and Technology Press Ltd., 1971) pp. 15–24.Google Scholar
[10] Marshall, D.B., Cox, B.N., and Evans, A.G., “The Mechanics of Matrix Cracking in Brittle Matrix Fiber Composites”, Acta Metall. Vol.3, No. 11 (1985) pp. 2013–2021.CrossRefGoogle Scholar
[11] Li, V.C. and Leung, C., “Theory of Steady State and Multiple Cracking of Random Discontinuous Fiber Reinforced Brittle Matrix Composites”, ASCE Journal of Engineering Mechanics, submitted for publication (1991).Google Scholar