Hostname: page-component-cd9895bd7-jkksz Total loading time: 0 Render date: 2024-12-28T20:04:17.282Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructure Evolution During Electric Current Induced Thermomechanical Fatigue of Interconnects

Published online by Cambridge University Press:  01 February 2011

Robert R. Keller ,
Roy H. Geiss ,
Yi-wen Cheng  and
David T. Read
Robert R. Keller
Affiliation:
Materials Reliability Division, National Institute of Standards and Technology, 325 Broadway, Boulder, CO 80305, U. S. A.
Roy H. Geiss
Affiliation:
Materials Reliability Division, National Institute of Standards and Technology, 325 Broadway, Boulder, CO 80305, U. S. A.
Yi-wen Cheng
Affiliation:
Materials Reliability Division, National Institute of Standards and Technology, 325 Broadway, Boulder, CO 80305, U. S. A.
David T. Read
Affiliation:
Materials Reliability Division, National Institute of Standards and Technology, 325 Broadway, Boulder, CO 80305, U. S. A.
Get access

Abstract

We demonstrate the evolution of microstructure and deformation associated with the use of electrical methods for evaluating mechanical reliability of patterned interconnects on rigid substrates. Thermomechanical fatigue in aluminum and copper interconnects was induced by means of low frequency (100 Hz), high density (> 10 MA/cm2) alternating currents, which caused cyclic Joule heating and associated thermal expansion strains between the metal lines and oxidized silicon substrate. The failure mechanism involved formation of localized plasticity, which caused topography changes on the free surfaces of the metal, leading to open circuit eventually taking place by melting at a region of severely reduced cross-sectional area. Both aluminum and copper responded to power cycling by deforming in a manner highly dependent upon variations in grain size and orientation. Isolated patches of damage appeared early within individual grains or clusters of grains, as determined by a quasi in situ scanning electron microscopy and automated electron backscatter diffraction measurement. With increased cycling, the extent of damage became more severe and widespread. We document some examples of the types of damage that mechanically confined interconnects exhibited when subjected to thousands of thermal cycles, including growth and re-orientation of grains in a systematic manner. We observed in the case of Al-1Si certain grains increasing by nearly an order of magnitude in size, and reorienting by greater than 30°. The suitability of electrical methods for accelerated testing of mechanical reliability is also discussed.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 863: Symposium B – Materials, Technology and Reliability of Advanced Interconnects , 2005 , B9.5
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Brotzen, F. R., Int. Mater. Rev. 39, 24 (1994).Google Scholar
2. Nix, W. D., Mater. Sci. Eng. A234, 37 (1997).Google Scholar
3. N, F. R.. Nabarro, Theory of Crystal Dislocations, 2nd ed. (Dover Publications, New York, 1987) pp. 618–641.Google Scholar
4. Huang, M., Suo, Z., and Ma, Q., J. Mech. Phys. Sol. 50, 1079 (2002).Google Scholar
5. Keller, R. R., Mönig, R., Volkert, C. A., Arzt, E., Schwaiger, R., and Kraft, O., in 6th International Workshop on Stress-Induced Phenomena in Metallization, edited by Baker, S. P., Korhonen, M. A., Arzt, E., and Ho, P., (AIP Conference Proceedings 612, American Institute of Physics, New York, 2002) pp. 119–132.Google Scholar
6. Mönig, R., Keller, R. R., and Volkert, C. A., Rev. Sci. Instrum. 75, 4997 (2004).Google Scholar
7. Geiss, R.H., Keller, R.R., Read, D.T. and Cheng, Y.W., this proceedings (2005).Google Scholar
8. Li Li Zhang, Wang, and Lu, , Phil. Mag. A82, 3129 (2002).Google Scholar