Clays are extremely variable materials with different mineral compositions, and they are the main ingredients in ceramics applications. Their properties play specific roles in influencing the technological properties and performance of ceramics products. Evaluating the various properties can help to determine the best way to utilize clay materials, such as the locally available Bombawuha (BC) and Denkaka (DC) clays mined from Ethiopia's Bombawuha and Denkaka areas, respectively. The objective of this study was to examine these materials for the purpose of using them to produce quality electrical porcelain insulators. The clay samples were characterized for their chemical composition, mineralogy, thermal properties, plasticity, and particle-size distribution, using atomic absorption spectrometry (AAS), X-ray diffractometry (XRD), differential thermal analysis coupled with thermogravimetric analysis (DTA-TGA), the Atterberg plasticity test, and sieve hydrometer analysis. Based on the characteristics, suitable clay materials were selected and mixed with feldspar and quartz to formulate various porcelain body compositions which were fired at three different temperatures (1200, 1250, and 1300°C) and dwell times (1.5, 2.0, and 2.5 h). The mineralogy, water adsorption, apparent porosity, bulk density, dielectric strength, flexural strength, and microstructure of the fired bodies were measured. The results revealed that, compared to DC, BC contains kaolinite as the major mineral with appreciable amounts of silica (46.72 wt.%), alumina (35.32 wt.%), and fluxing oxides but smaller amounts of CaO. BC contains greater clay fractions (20.58 wt.%); and has a middle-range plasticity index (PI = 11.2 wt.%), thus making BC suitable for producing porcelain insulators. A test-body composition of 40 wt.% BC, 40 wt.% feldspar, and 20 wt.% quartz, fired at 1250°C for 2 h, exhibited water adsorption of 0.17 wt.%, apparent porosity of 0.42 wt.%, bulk density of 2.45 g/cm3, a dielectric strength of 8.22 kV/mm, and flexural strength of 43.63 MPa and, thus, satisfied the required properties for quality porcelain insulators.

The negative effects of dye-contaminated wastewater on humans and the environment are well known, so the wastewater must be treated carefully before discharge into the environment. To overcome those impacts, the search for environmentally friendly and low-cost materials is essential, especially in developing countries The objective of the present study was to determine the feasibility of using bauxite from Malaysia as a new and efficient ceramic, hollow-fiber membrane for the degradation of reactive dyes in wastewater. A porous, hollow-fiber membrane was fabricated from bauxite (BHFM) using a phase-inversion technique, followed by sintering at various temperatures. The BHFM consisted of two types of voids, having either a finger-like or a sponge-like structure. As the sintering temperature was increased, the porosity of the BHFM decreased from 46.5 to 9.5%. The greatest mechanical strength of 308.1 MPa was achieved when the BHFM was loaded with 55 wt.% of bauxite and sintered at 1450°C. The remaining 45 wt.% consisted of solvent, polymer binder, and dispersant. The BHFM functioned well as a membrane for microfiltration and a support membrane for ultrafiltration. BHFM with loading of 45 wt.%, 50 wt.%, and 55 wt.% successfully eliminated 90%, 94%, and 98% of 10 ppm reactive dye (RB5) when sintered at the highest temperature.

This study focuses on the main factors determining the apparent porosity of porous bioceramics prepared using small organic foam spheres as the pore-making reagent, in order to determine the best technical parameters for preparing porous bioceramics. In every experiment, only one of these factors (the time of heating, the sintering temperature, the mass ratio between small organic foam spheres and beta-tricalcium phosphate (β-TCP) powder, and the rate of the temperature rise) was changed, while the others were kept constant. In each case the apparent porosity was tested and the relation between the specific variable and apparent porosity was observed. Finally, the optimum technical parameters were deduced. The apparent porosity shows an inverse linear relation to the time of heating and the sintering temperature, and is approximately proportional to the mass ratio between the small organic foam spheres and the β-TCP powder and the rate of temperature rise. These factors have important influences on the apparent porosity. The optimum conditions were: heating time (soak time) 120 min, sintering temperature 850ºC, mass ratio 0.25, and a rate of temperature increase of 120ºC h–1.