In our earlier papers, we demonstrated that plasma pressure decreases with the growing atomic number of the target material. That experimentally confirmed fact brought about a question whether it would be possible to collimate the Al plasma outflow by using plastic plasma as a compressor. To prove that idea we used in our next experiments a plastic target with an Al cylindrical insert of 400 µm in diameter. The measurements were carried out at the Prague Asterix Laser System iodine laser facility. The laser provided a 250 ps (full width at half maximum (FWHM)) pulse with energy of 130 J at the third harmonic frequency (λ3 = 0.438 µm). The focal spot diameters (ΦL) 800, 1000, and 1200 µm ensured predominance of the plastic plasma amount high enough for the effective Al plasma compression. To study the Al plasma stream propagation and its interaction with plastic plasma a three-frame interferometric system and an X-ray camera were used. The experiment provided a proof that creation of the collimated Al plasma jet by action of outer plastic plasma is feasible. In order to discuss of the experimental results a thorough theoretical analysis was carried out.

Our earlier papers demonstrate a very simple method of plasma jet formation, consisting in irradiating a massive planar target of a relatively high atomic number by a partly defocused laser beam. Our present interest is concentrated on interaction of the plasma jet with other media. This paper is aimed at investigations of interaction of two jets launched successively on Cu target. Our attention was paid to the role of radiative cooling in the plasma jet formation. The experiment was carried out at the PALS iodine laser facility. The laser provided a 250-ps (full width at half maximum) pulse with energy of 130 J at the third harmonic frequency (λ3 = 0.438 µm). Two successive jets were produced on a massive flat Cu target provided with a cylindrical channel 5 mm long and 400 µm in diameter. Since the focal spot diameter of the laser beam on the target surface was larger than that of the channel (800 µm), the annular irradiation of the target face resulted in creation of the first plasma jet, whereas the second jet was produced by action of the central part of laser beam on the channel wall. Three-frame interferometric system, X-ray streak camera, and a set of ion collectors were used as diagnostic tools.

This paper is devoted to investigations of laser energy transfer into solid targets with respect to the focusing lens focal point position relative to the solid target surface as obtained at the PALS laser facility. The third harmonic of the PALS laser beam with energy ~90 J and pulse duration ~250 ps (FWHM) was used for irradiation of two kinds of targets made of Cu: a slab and a 3.6 µm thick foil. The focal point of the beam was located either inside or in front of the target surface, and care was taken to ensure the same laser spot radii in both cases (250 µm). It was demonstrated that these two opposite focal point positions give rise to significantly different laser-plasma interactions: with either depression or maximum of the laser intensity distribution in the center of the beam, respectively. It was also verified that the focal point position inside of the target is favorable for plasma jets creation, whereas the opposite case is more effective for acceleration of flyers.

Our recent experimental results demonstrate that the formation of plasma jets is a fundamental process accompanying the laser produced plasma expansion, if a massive planar target with relatively high atomic number is irradiated by a defocused laser beam. In this paper some new results on the influence of target irradiation conditions on plasma jet parameters are presented. The experiment was carried out at the PALS iodine laser facility, with the third harmonic beam of the pulse duration of 250 ps (FWHM). The beam energies varied in the range of 13–160 J, the focal spot radii in the range of 35–600 µm. The planar massive targets used in the experiment were made of Cu, Ag and Ta. For measurements of the electron density evolution a three frame interferometric system was employed. The jets were observed in the whole range of the laser energy used. The initial velocities of the plasma jets produced in the reported experiment reached the value of up to 7·107 cm/s, the jets were up to 4 mm long including the jet pedestal and about 400 µm in diameter. Calculations of the efficiency of the plasma jet production show that it decreases with increasing the laser energy.