A high-power all polarization-maintaining (PM) chirped pulse amplification (CPA) system operating in the 2.0 μm range is experimentally demonstrated. Large mode area (LMA) thulium-doped fiber (TDF) with a core/cladding diameter of 25/400 μm is employed to construct the main amplifier. Through dedicated coiling and cooling of the LMA-TDF to manage the loss of the higher order mode and thermal effect, a maximum average power of 314 W with a slope efficiency of 52% and polarization extinction ratio of 20 dB is realized. The pulse duration is compressed to 283 fs with a grating pair, corresponding to a calculated peak power of 10.8 MW, considering the compression efficiency of 88% and the estimated Strehl ratio of 89%. Moreover, through characterizing the noise properties of the laser, an integrated relative intensity noise of 0.11% at 100 Hz−1 MHz is obtained at the maximum output power, whereas the laser timing jitter is degraded by the final amplifier from 318 to 410 fs at an integration frequency of 5 kHz to 1 MHz, owing to the self-phase modulation effect-induced spectrum broadening. The root-mean-square of long-term power fluctuation is tested to be 0.6%, verifying the good stability of the laser operation. To the best of our knowledge, this is the highest average power of an ultrafast laser realized from an all-PM-fiber TDF-CPA system ever reported.

An all-fiber high-power linearly polarized chirped pulse amplification (CPA) system is experimentally demonstrated. Through stretching the pulse duration to a full width of approximately 2 ns with two cascaded chirped fiber Bragg gratings (CFBGs), a maximum average output power of 612 W is achieved from a high-gain Yb-doped fiber that has a core diameter of 20 μm with a slope efficiency of approximately 68% at the repetition rate of 80 MHz. At the maximum output power, the polarization degree is 92.5% and the M2 factor of the output beam quality is approximately 1.29; the slight performance degradations are attributed to the thermal effects in the main amplifier. By optimizing the B-integral of the amplifier and finely adjusting the higher-order dispersion of one of the CFBGs, the pulse width is compressed to 863 fs at the highest power with a compression efficiency of 72%, corresponding to a maximum compressed average power of 440.6 W, single pulse energy of 5.5 μJ and peak power of about 4.67 MW. To the best of our knowledge, this is the highest average power of a femtosecond laser directly generated from an all-fiber linearly polarized CPA system.

The Orion laser facility at AWE provides multiple beams to target delivering synchronized pulses at both nanosecond and sub-picosecond duration. In the latter, the peak power approaches the petawatt level. This paper presents a conceptual design for potential development of these beamlines. This would deliver a significant enhancement of performance at the fundamental level. In addition, a new approach is described for the management of frequency conversion at high intensity, which may allow significantly enhanced performance at the second harmonic also.

In this paper, we innovatively conduct a Porro prism-based beam pointing stability promotion technique research and realize a high-performance rod-type photonic crystal fiber-based chirped pulse amplification (CPA) system, mainly including a frequency-reduced all-fiber pre-amplification stage, photonic crystal rod-based main amplification stage, and 1600 lines/mm transmission grating-pair compressor. Laser output with average power of 50 W, repetition rates of 500 kHz, pulse energy of 100 μJ, pulse duration of 830 fs, beam quality of M2<1.3, power fluctuation of 0.55% root mean square, and beam pointing drift of 19 μrad/°C over 8 h is realized. The high-performance laser system has an enormous application potential in fundamental research and precision manufacturing fields.

We demonstrate a high-contrast, joule-level Nd:glass laser system operating at 0.5 Hz repetition rate based on a double chirped pulse amplification (CPA) scheme. By injecting high-contrast, high-energy seed pulses into the Nd:glass CPA stage, the pulse energy is amplified to 1.9 J through two optical parametric CPA stages and two Nd:glass amplifiers. The temporal contrast of compressed pulse is measured down to the level of $10^{-8}$ at tens of ps, and $10^{-10}$ near 200 ps before the main pulse, respectively.

The dispersion of a pair of prisms is analyzed by means of a ray-tracing method operating at other than tip-to-tip propagation of the prisms, taking into consideration the limited spectral bandwidth. The variations of the group delay dispersion and the third-order dispersion for a pair of prisms are calculated with respect to the incident position and the separation between the prisms. The pair of prisms can provide a wide range of independent and continuous third-order dispersion compensation. The effect of residual third-order dispersion on the pulse contrast ratio and pulse duration is also calculated. The residual third-order dispersion not only worsens the pulse contrast ratio, but also increases the pulse duration to the hundreds of femtosecond range for a tens of femtosecond pulse, even when the residual third-order dispersion is small. These phenomena are helpful in compensating for the residual high-order dispersion and in understanding its effect on pulse contrast ratios and pulse durations in ultrashort laser systems.

We develop a splicing technology of Ti:sapphire crystals for a high-energy chirped pulse amplifier laser system that can suppress the parasitic lasing to improve the amplification efficiency compared to a large-size single Ti:sapphire crystal amplifier. Theoretical investigations on the characteristics of the amplifier with four splicing Ti:sapphire crystals, such as parasitic-lasing suppression and amplification efficiencies, are carried out. Some possible issues resulting from this splicing technology, including spectral modulation, stretching or splitting of the temporal profile, and the sidelobe generation in the spatial domain (near field and far field), are also investigated. Moreover, the feasibility of the splicing technology is preliminarily demonstrated in an experiment with a small splicing Ti:sapphire crystals amplifier. The temporal profile and spatial distribution of the output pulse from the splicing Ti:sapphire crystal amplifier are discussed in relation to the output pulse from a single Ti:sapphire crystal amplifier.

Two different pulse cleaning techniques for ultra-high contrast laser systems are comparably analysed in this work. The first pulse cleaning technique is based on noncollinear femtosecond optical-parametric amplification (NOPA) and second-harmonic generation (SHG) processes. The other is based on cross-polarized wave (XPW) generation. With a double chirped pulse amplifier (double-CPA) scheme, although temporal contrast enhancement in a high-intensity femtosecond Ti:sapphire chirped pulse amplification (CPA) laser system can be achieved based on both of the techniques, the two different pulse cleaning techniques still have their own advantages and are suitable for different contrast enhancement requirements of different laser systems.