Toxic pharmaceutical pollutants, such as nicotine, represent a significant threat to natural water sources due to their continuous discharge. To address this issue, clay minerals and their composites have demonstrated exceptional adsorptive and remedial capabilities for wastewater purification. This research focused on developing green clay-polymeric adsorbents for the efficient removal of pharmaceutical pollutants from industrial wastewater. The synthesis involves creating halloysite nanotube–polythiophene nanocomposites through a green and cost-effective method using vapour polymerization and a solvent-free, ball-milled technique for the adsorptive removal of nicotine from wastewater. The investigation evaluates the impacts of preparation, modification and environmental conditions on the adsorptive performance of these clay-based nanocomposites compared to pure polythiophene. The polymerization process was evaluated by varying the vapour polymerization holding time for a fixed amount of oxidant (FeCl3) and halloysite nanotube (HNT) to investigate the impacts of monomer vapour exposure time on the polymerization of nanocomposites. Following the characterization of the synthesized adsorbents using various methods, the study investigated the impacts of various parameters (e.g. adsorbent dosage, pH and contact time) on the adsorption capabilities of the materials on a laboratory scale. The results revealed that the incorporation of HNT improved the adsorbing performance of nanocomposites. The pH, absorbent concentration and contact time directly affect nicotine adsorption. Significantly, halloysite–polythiophene 3 with a 2 h polymerization duration demonstrated the maximum adsorption efficacy of 78.94% at pH 10 after a 24 h contact time. The environmentally friendly halloysite-based nanocomposite shows promising potential as an effective adsorbent for pharmaceutical pollutant (nicotine) removal from aquatic environments.

Thermoplastic polyurethane (TPU) matrix was reinforced with polyhedral oligomeric silsesquioxane (POSS) and halloysite nanotubes (HNT), both separately and combined. Composite samples were fabricated using a melt-compounding method. Characterization of the composites obtained was performed via tensile and hardness tests, melt-flow index measurements (MFI), abrasion tests, dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM) to investigate the mechanical performance, flow behaviour, tribological characteristics, thermo-mechanical response and morphological properties. The greatest tensile strength value was obtained for the smallest HNT content. Further addition of HNT resulted in agglomerations for both POSS and HNT particles. The shore hardness of TPU was enhanced by filler inclusions. The TPU/POSS composites displayed significant improvement in terms of abrasion resistance compared to TPU at lower loading levels. The DMA study showed that composites containing 0.5% POSS and 1.0% HNT displayed the greatest storage modulus. The glass-transition temperature of TPU shifted to smaller values with the addition of both nanoparticles. The HNT inclusions increased the MFI value of TPU because of their large aspect ratio. Homogeneous mixing of nanoparticles in the TPU matrix was confirmed by a SEM study of the composites. Their dispersion decreased as the concentrations of POSS and HNT increased. An adjuvant effect of POSS with HNT was achieved in their hybrid composites.

The adsorption and retention of phosphates in soil systems is of wide environmental importance, and understanding the surface chemistry of halloysite (a common soil clay mineral) is also of prime importance in many emerging technological applications of halloysite nanotubes (HNTs). The adsorption of phosphate anions on tubular halloysite (7 Å) has been studied to gain a greater understanding of the mechanism and kinetics of adsorption on the surface of HNTs. Two well-characterized tubular halloysites with differing morphologies have been studied: one polygonal prismatic and one cylindrical, where the cylindrical form has a greater surface area and shorter tube length. Greater phosphate adsorption of up to 42 μmol g–1 is observed on the cylindrical halloysite when compared to the polygonal prismatic sample, where adsorption reached a maximum of just 15 μmol g–1 compared to a value for platy kaolinite (KGa-2) of 8 μmol g–1. Phosphate adsorption shows strong pH dependence, and the differences in phosphate sorption between the prismatic and cylindrical morphologies suggest that phosphate absorption does not occur at the same pH-dependent alumina edge sites and that the lumen may have a greater influence on uptake for the cylindrical form.