The composition of carbides in steel, measured by atom probe tomography, can be influenced by limitations in the ion detector system. When carbides are analyzed, many ions tend to field evaporate from the same region of the specimen during the same laser or voltage pulse. This results in a so-called multiple event, meaning that several ions impact the detector in close proximity both in time and space. Due to a finite detector dead-time not all ions can be detected, a phenomenon known as detector pile-up. The evaporation behavior of carbon is often different than the evaporation behavior of metals when analyzing alloy carbides, leading to preferential loss of carbon ions, and a measured carbon concentration below the expected value. This effect becomes stronger as the overall detection efficiency gets higher. Here, the detection efficiency was deliberately reduced by inserting a grid into the flight-path, which resulted in a higher and more correct carbon concentration, accompanied by an increase in the statistical uncertainty.

The exposure to solar radiation (mainly due to the action of ultraviolet radiation) is one of the main causes for the premature failure of many polymeric materials, including the geotextiles. In this work, a nonwoven polypropylene geotextile (stabilized with a known amount of a hindered amine light stabilizer) was exposed to ultraviolet-aging tests, both in the laboratory (accelerated conditions) and outdoors (natural conditions). The damage occurred in the geotextile (caused by the ultraviolet-aging tests) was evaluated quantitatively (by monitoring changes in its mass per unit area, thickness, and tensile properties) and qualitatively (by scanning electron microscopy). The results, among other findings, showed that: (1) the ultraviolet-aging tests (both in the laboratory and outdoors) induced relevant damage in the polypropylene fibers of the geotextile (transverse cracks), leading to the deterioration of its tensile behavior, (2) the amount of degradation increased with the increase of the ultraviolet radiant energy, (3) the laboratory tests caused a faster deterioration of the polypropylene fibers than the outdoor tests, and (4) the degradation found by scanning electron microscopy in the polypropylene fibers correlated well with the deterioration occurred in the tensile behavior of the geotextile.

In this work, strongly blue emitting Ce3+-activated BaAl2O4 nanophosphors were successfully synthesized by a sol–gel technique. The crystal structure, morphology, and microstructure of the nanophosphors have been studied by X-ray powder diffraction, field emission scanning electron microscopy, and high-resolution transmission electron microscopy. The photoluminescence spectra show the impact of concentration variation of Ce3+ on the photoluminescence emission of the phosphor. These nanophosphors display intense blue emission peaking at 422 nm generated by the Ce3+ 5d → 4f transition under 350 nm excitation. Our results reveal that this nanophosphor has the capability to take part in the emergent domain of solid-state lighting and field-emission display devices.

Previous evidence suggested that lymphocytic thyroiditis (LT) was a variant of Hashimoto's thyroiditis (HT), thus the aim of the current study is to quantify structural changes in histological specimens taken from HT and LT patients. A total of 600 images containing a single lymphocyte nucleus (300 nuclei per group) were obtained from 20 patients with HT and LT. In order to quantify changes in the nuclear architecture of investigated lymphocytes, the fractal dimension (FD) and some gray-level co-occurrence matrix texture parameters (angular second moment, inverse difference moment, contrast, entropy, and correlation) were calculated for each nucleus. A statistically significant difference in the FD of the “binary-outlined” nucleus and that of the corresponding “black-and-white” nucleus was detected between HT and LT lymphocyte nuclei. In addition, there was also a statistically significant difference in contrast and correlation between HT and LT lymphocyte nuclei. In conclusion, the results of this study suggested that there was a difference in structural complexity between investigated lymphocyte nuclei; additionally, LT lymphocytes possessed probably more complex texture and larger variations as well as more asymmetrical nuclei compared with HT lymphocytes. Accordingly, these findings indicate that LT is probably not a variant of HT; however, more complex studies are necessary to estimate differences between these types of thyroiditis.

The aims of the present study were to: (i) evaluate the ultrastructural differences in the zona pellucida (ZP) surface between immature and mature bovine oocytes, and (ii) describe a new objective technique to measure the pores in the outer ZP. Intact cumulus–oocyte complexes (COCs) obtained from a local abattoir were immediately fixed (immature group) or submitted to in vitro maturation (IVM) at 38.5 °C for 24 h in a humidified atmosphere of 5% CO2 in air (mature group). Oocytes from both groups were morphologically evaluated via Scanning Electron Microscopy (SEM) and the images were processed in the Fiji/ImageJ software using a new objective methodology through the Trainable Weka Segmentation plugin. The average number of pores in ZP was greater (p < 0.05) in the mature group than the immature group. However, the size and circularity of pores in ZP did not differ (p > 0.05) between groups. In conclusion, it has been shown that the number of pores highlighted the main ultrastructural change in the morphology of the ZP surface of bovine oocytes during the IVM process. We have described an objective method that can be used to evaluate ultrastructural modifications of the ZP surface during oocyte maturation and early embryo development.

This work used a multi-analytical approach to characterize two 19th century ambrotypes and was motivated by the lack of insight on these historical objects. Photographic imaging and optical microscopy (OM) were used to identify abrasions, cracks related to reticulation, tarnishing, and other aspects associated to production and degradation processes. With variable pressure scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (EDS) these processes were seen with great detail and further characterized. Elemental point analysis and elemental mapping showed that the photosensitive material used was silver iodide. Degradation compounds were found as silver and chlorine-containing compounds. In one of the items, the tarnishing area also contained redeposited silver in a ring-shape surrounding a nucleus rich in silver, copper, and sulfur, in addition to copper-based salts. EDS analyses also identified that the supports were common soda–lime–silica glasses, refined with arsenic; and showed that a pigment rich in iron was used in both items to hand color the cheeks, extended with aluminum silicates alone or mixed with barium sulfate. The μ-Raman study pointed out that a synthetic Mars pigment was employed. μ-Fourier-transform infrared spectroscopy analyses identified collodion as the binder. Shellac was used as a protective varnish in one of the items and a gum was possibly employed on the other. Bitumen was used for the background in one ambrotype.

This study investigated the histomorphological features of developing rabbit respiratory acini during the postnatal period. On the 1st day of postnatal life, the epithelium of terminal bronchiole consisted of clear cells which intercalated between few ciliated and abundant non-ciliated (Clara) cells. At this age, the rabbit lung was in the alveolar stage. The terminal bronchioles branched into several alveolar ducts, which opened into atria that communicated to alveolar sacs. All primary and secondary inter-alveolar septa were thick and showed a double-capillary network (immature septa). The primitive alveoli were lined largely by type-I pneumocytes and mature type-II pneumocytes. The type-I pneumocytes displayed an intimate contact with the endothelial cells of the blood capillaries forming the blood–air barrier (0.90 ± 0.03 µm in thickness). On the 3rd day, we observed intense septation and massive formation of new secondary septa giving the alveolar sac a crenate appearance. The mean thickness of the air–blood barrier decreased to reach 0.78 ± 0.14 µm. On the 7th day, the terminal bronchiole epithelium consisted of ciliated and non-ciliated cells. The non-ciliated cells could be identified as Clara cells and serous cells. New secondary septa were formed, meanwhile the inter-alveolar septa become much thinner and the air–blood barrier thickness was 0.66 ± 0.03 µm. On the 14th day, the terminal bronchiole expanded markedly and the pulmonary alveoli were thin-walled. Inter-alveolar septa become much thinner and single capillary layers were observed. In the 1st month, the secondary septa increased in length forming mature cup-shaped alveoli. In the 2nd month, the lung tissue grew massively to involve the terminal respiratory unit. In the 3rd month, the pulmonary parenchyma appeared morphologically mature. All inter-alveolar septa showed a single-capillary layer, and primordia of new septa were also observed. The thickness of the air–blood barrier was much thinner; 0.56 ± 0.16 µm. TUNEL assay after birth revealed that the apoptotic cells were abundant and distributed in the epithelium lining of the pulmonary alveoli and the interstitium of the thick interalveolar septa. On the 7th day, and onward, the incidence of apoptotic cells decreased markedly. This study concluded that the lung development included two phases: the first phase (from birth to the 14th days) corresponds to the period of bulk alveolarization and microvascular maturation. The second phase (from the 14th days to the full maturity) corresponds to the lung growth and late alveolarization.

X-ray diffraction (XRD) and high-resolution scanning electron microscopy (SEM) have been used to characterize the silver mercury amalgam particles resting on the surface that comprise the image of five daguerreotype plates that were not gilded and that were prepared by three different contemporary daguerreotype makers. The regions of interest of the surface that were examined were overexposed, solarized, and highlight (white) areas. The XRD portion of the study shows that the two main silver mercury amalgam particles identified using the International Center for Diffraction Data PF4 + database were the Schachnerite/ζ (zeta) phase amalgam, Ag1.1Hg0.9, and the mercury silver amalgam, Ag0.65Hg0.35. On one of the daguerreotypes a third silver mercury amalgam, Moschellandsbergite, Ag2Hg3, was also identified in small concentrations. High-resolution SEM images corroborate the diffraction data and show that the crystalline nature of the silver mercury amalgam particles on all five plates to be mostly hexagonal, which would correspond to the Schachnerite/ζ (zeta) phase amalgam, and fewer rectangular solid and cubic crystals corresponding to the mercury silver amalgam.

Small additions of boron can remarkably improve the long-term creep resistance of 9–12% Cr steels. The improvement has been attributed to boron segregation to grain boundaries during quenching, and subsequent boron incorporation into certain families of precipitates during tempering. However, the detailed mechanisms are not yet fully understood. Atom probe tomography (APT) is an excellent technique for gaining insights into boron distribution, however, in order to acquire accurate analysis of boron in 9–12% Cr steels using APT, there are several key challenges. In order to better understand and address these challenges, we developed a novel method for site-specific APT specimen preparation, which enables convenient preparation of specimens containing specifically selected grain boundaries positioned approximately perpendicular to the axis of the APT tip. Additionally, when analyzing boron at boundaries and in carbides (as diluted solute) and borides, a widening of the profile of boron distribution compared to other elements was repeatedly observed. This phenomenon is particularly analyzed and discussed in light of the evaporation field of different elements. Finally, the possible effects of detector dead-time on quantitative analysis of boron in metal borides are discussed. A simple method using 10B correction was used to obtain good quantification.

The aim of the present study was to map the painting materials, degradation processes, and biological features present on the mural painting in the church of St. Mary in Beram (Croatia) to study their possible interaction and produce information helping the preservation of this valuable painting. The research was conducted on micro samples of painting materials taken from different sites along the painting and the characterization of the present fungal species was carried out. The painting samples, together with observable patinas and degradation products, were studied by optical microscopy (OM), scanning electron microscopy, energy-dispersive spectroscopy (SEM/EDS), Fourier-Transform Infrared spectroscopy, and powder X-ray diffraction. Fungal diversity was studied using cultivation methods followed by OM and SEM analyses in addition to molecular analysis. The results contribute to the characterization of the original painting materials, successively added materials and occurred interventions, to the understanding of degradation progressions and fungal biotransformation processes. A mineral, cumengite, a copper-based pigment extremely rarely used in art, was found. Its occurrence together with barium sulfate, gypsum, and calcium oxalate possibly produced by microbiological activity was studied and information was added regarding the composition of painting materials in St. Mary church mural cycle.

Five scarabs and one scaraboid found in Vinha das Caliças 4 (Beja, Portugal) were analyzed using a micro-analytical methodology in order to determine their mineralogical and chemical composition. Microstructural characterization and chemical analysis revealed that all were composed of a white body of crushed feldspathic sand covered by a lead-rich, alkaline-depleted silicate blue-green glaze showing evident signs of glass deterioration. Variable pressure scanning electron microscopy with X-ray energy dispersive spectrometry, handheld X-ray fluorescence spectroscopy, and micro X-ray diffraction results show that blue-green color of the glaze was produced by using copper ions (Cu2+) in conjunction with the lead antimonate bindheimite, a yellow-colored opacifier. The introduction of small amounts of tin in the structure of bindheimite enabled the production of a ternary Pb–Sb–Sn oxide. Tin, which was most likely added with the copper source (bronze scrapings), is known to facilitate the crystallization of bindheimite. The results are consistent with the five scarabs and one scaraboid being manufactured in Egypt. This study, the first archeometric study of scarabs found in the Iberian peninsula, has greatly contributed to the understanding of the influence of the Eastern and Central Mediterranean world in the Southwestern Iberia during the first millennium B.C.

The key role of the epididymis is contributing to sperm storage, maturation, and survival. The epididymis of camel has a unique structure called the intraepithelial gland. The present work aimed to investigate the structure of the epididymal intraepithelial gland with special references to the seasonal variation. The samples were collected from the distal part of the corpus epididymes of completely healthy mature camels (Camelus dromedarius) in the breeding and nonbreeding seasons. Tomato lectin-positive material had been demonstrated within the epididymal spermatozoa. Here, we provide the first transmission electron microscopic study for the intraepithelial gland of camel epididymis detecting the autophagy during the nonbreeding season. The autophagosomes originated from the endoplasmic reticulum, surrounding mitochondria, and located mainly next to the basement membrane. This location is probably valuable for subsequent passing of their contents into the interstitium for possible recycling. The histochemical and ultrastructural characteristics of the gland in the breeding season indicated a hyperactive secretory microenvironment enriched with the glycoprotein-producing machinery, which could be controlled by androgens. The present data suggest that the camel intraepithelial gland has a significant impact on the reproductive activity through their secretory microenvironment during the breeding season. Moreover, it recycles the unused organelles or proteins for reuse or to supply energy under stress conditions in the nonbreeding season.