This paper describes a compact and efficient rectenna based on a dual-diode microstrip rectifier at 2.45 GHz. This circuit has been designed and optimized using a global analysis technique which associates electromagnetic and circuit approaches. Due to the differential topology of the rectifier, neither input low-pass filter nor via-hole connections are needed. This makes the structure more compact reducing losses. Measurements of a single rectenna element show 83% efficiency over an optimal load of 1050 Ω at a power density of 0.31 mW/cm2. To increase the received RF power and then increase dc power over the load, identical rectennas have been interconnected to form arrays. Two and four elements rectenna arrays, connected either in parallel or in series, have been developed. It was shown that by properly choosing the interconnection topology and the optimal output load, higher dc voltage or dc power have been obtained. The four-element series-connected array can provide experimentally up to 3.85 times output dc voltage compared to the single rectenna. The parallel-connected rectenna arrays generate approximately 2.15 and 3.75 times output dc power for two and four elements, respectively.

This paper reports the test results of a small-scale prototype that implements a digitally beam-formed phased antenna array in the E-band. A four-channel dual-conversion receive RF module for 71–76 GHz frequency band has been developed and integrated with a linear end-fire antenna array. Wideband frequency-domain angle-of-arrival estimation and beam-forming algorithms were developed and implemented using Orthogonal Frequency Division Multiplexing (OFDM) with Quadrature Phase-Shift Keying (QPSK) at 1 Gbps. Measured performance is very close to the simulated results and experimental data for an analogue-beam-formed array. This work is a stepping stone toward practical realization of larger hybrid arrays in the E-band.

In this paper, a method for design and optimization of folded reflect-array antennas is proposed based on particleswarm optimization (PSO). In addition to such a powerful optimization algorithm, two further requirements have to be fulfilled. The first one is a good and fast algorithm for the exact prognosis of the far-field radiation diagram, resulting from a specific element configuration on the reflector. Additionally, a good choice of the fitness function for the evaluation of the resulting radiation diagrams is necessary. In both, reflect-array-related aspects such as phase truncation, reflection losses, and cell discontinuities have to be considered. Antenna optimization based on this technique is presented in this paper at the example of two 77 GHz folded reflect-array antennas. The efficiency of this approach is demonstrated with these examples, and the results are verified by measurement, showing an excellent agreement with the specifications of the diagram masks. The implemented tool, including a realistic antenna diagram preview, allows the investigation of the design parameters’ influence on the antenna performance, such as illumination amplitude, high substrate losses, and phase truncation.

A novel calibration network for patch antennas is proposed. We introduce magnetically coupled in-situ probes, which excite the fundamental patch mode. In that way, finite array effects and mutual coupling are taken into account, providing the opportunity for accurate online calibration of active antenna terminals. The specific advantages of the approach are demonstrated for linearly polarized patch antennas. Realization aspects of the multilayer antenna are discussed and the effect of some fabrication imperfections are investigated. Measured S-parameters as well as radiation simulation results of a single patch with the integrated probes are presented. Based on simulation of antenna arrays with in-situ probes the calibration accuracy is given in theory.

A simple method for the full characterization of passive n-port microwave monolithic integrated circuit (MMIC) structures using standard two-port vector network analyzer (VNA) measurements is presented. Its main advantages are: it does not require to perform measurements from all the ports of the network, no special calibration procedure is needed, the auxiliary terminations required by the procedure can be integrated at the border of the structure under test with minimal area increase, and it can be easily implemented in commercial CAD software. The method was applied to a nine-port microstrip structure corresponding to the output power combiner and impedance matching network of an X-band MMIC high power amplifier (HPA). The full S-parameter matrix was derived from two-port measurements and compared to the circuit–as well as electromagnetic (EM)-based simulations of the structure.

A broadband permeability measurement method based on the full-wave electromagnetic (EM) analysis of a non-reciprocal transmission line is presented. The dispersion diagram for the first significant modes inside the ferrite loaded section of the line is obtained. The presence of magnetostatic modes generated by the magnetized ferrite inside the line is verified. Using a mode matching technique, the theoretical scattering parameters (S-parameters) of the transmission line are calculated. The full-wave analysis is validated with measurements of material properties in limit cases.

Doubled frequency optical two-tone generation and optical single sideband (SSB) modulation by the dual-electrode-type electro-optic (EO) modulator with a single Mach–Zehnder (MZ) interferometer were considered. We theoretically showed that redundant spectrum components in the modulated optical signals, which are caused by the imbalance of light splitting ratio between the two arms of the interferometer, are significantly suppressed by controlling the input power ratio of RF modulation signals applied to each electrode. This effect was confirmed by the experiment, where an optical two-tone with the redundant components 49.8 dB lower than the primary two-tone components in intensity level was obtained. This method is also valid for suppression of undesired frequency components of RF signals that are generated at a photo detector from the optical two-tone waves propagated through a dispersive optical fiber.

A study of the electrical performances of AlInN/GaN High Electron Mobility Transistors (HEMTs) on SiC substrates is presented in this paper. Four different wafers with different technological and epitaxial processes were characterized. Thanks to intensive characterizations as pulsed-IV, [S]-parameters, and load-pull measurements from S to Ku bands, it is demonstrated here that AlInN/GaN HEMTs show excellent power performances and constitute a particularly interesting alternative to AlGaN/GaN HEMTs, especially for high-frequency applications beyond the X band. The measured transistors with 250 nm gate lengths from different wafers delivered in continuous wave (cw): 10.8 W/mm with 60% associated power added efficiency (PAE) at 3,5 GHz, 6.6 W/mm with 39% associated PAE at 10.24 GHz, and 4.2 W/mm with 43% associated PAE at 18 GHz.

This paper reports on a novel voltage-mode class-S power amplifier for the 450 MHz band, based on GaN–HEMT monolithic microwave integrated circuits (MMICs). It achieves a peak output power of 3.4 W for a single tone at 400 MHz, encoded in standard band-pass delta-sigma modulation with 1.6 Gbps sampling frequency. The corresponding efficiency is 38%, peaking at 52% for 0.5 W output power. In order to demonstrate the influence of coding efficiency, additional measurements using a periodic square-wave signal were performed (class-D operation), which yield a maximum output power of 7 W with 64% efficiency. To the author's knowledge, these are the best results in this frequency range achieved so far with the voltage-mode class-S configuration. The paper discusses behavior at power back-off and the influence of the loss mechanisms.

This work describes the integration of Schottky diodes into fast GaN MMIC process technology suitable for the realization of switch-mode power amplifier core chips for class-S operation at 2 GHz. With the demonstration of this technology, the so-called third-quadrant issue, which reduces the efficiency in band pass-Δ-Σ class-S operation can be diminished on device level. Compared to a hybrid diode assembly, the broadband properties of the amplifier module with on-chip-integrated diode can be improved by the reduction of parasitic losses. The GaN heterostructure field effect transistors (HFETs) with integrated series diode show a cut-off frequency of 28 GHz with drain breakdown voltages exceeding −100 and +100 V and comparable large signal performance to conventional GaN HFETs at 10 GHz. MMIC core chips for class-D and class-S switch-mode power amplifier modules are demonstrated for the operation at mobile communication frequencies between 0.45 and 2 GHz and signal bit rates up to 8 Gbps. The circuits yield broadband output power levels between 4 and 9 W with efficiencies of up to 80%.

Burst mode operation is proposed as an efficiency improving technique for power amplifiers. The core idea is to modulate the amplitude of the envelope signal into a series of square-wave pulses such that the width of the signal burst or the total amount of pulses are varied according to the envelope. The phase information is still contained by the timing of the pulses. This work presents the efficiency and linearity analysis of burst mode radio frequency (RF)/power amplifier (PA). In addition, the efficiency performance is compared when the burst mode RF power amplifiers (PA) is connected to a wideband load or a narrowband filter. It is shown that burst mode PAs are more efficient than the conventional Class B PAs. To achieve an even more favorable efficiency, a transmission line is inserted between the output of the switching RF PA and the filter to improve the filter's impedance characteristic. Additionally, the efficiency and linearity of the burst mode PA with and without transmission line has been studied and simulated thoroughly. To demonstrate the validity of the efficiency formulas and linearity considerations, a printed circuit board (PCB)-mounted burst mode PA using a laterally diffused metal oxide semiconductor (LDMOS) transistor was fabricated. Measurements show a peak efficiency of 78% and 28.8 dBm of output power.

The high millimeter-wave (mmW) frequency range offers new possibilities for high-resolution imaging and sensing as well as for high data rate wireless communication systems. The use of power amplifiers of such systems boosts the performance in terms of operating range and/or data rate. To date, however, the design of solid-state power amplifiers at frequencies about 210 GHz suffers from limited transistor model accuracy, resulting in significant deviation of simulation and measurement. This causes cost and time consuming re-design iterations, and it obstructs the possibility of design optimization ultimately leading to moderate results. For verification of the small-signal behavior of our in-house large-signal transistor model, S-parameter measurements were taken from DC to 220 GHz on pre-matched transistors. The large-signal behavior of the transistor models was verified by power measurements at 210 GHz. After model modification, based on process control monitor (PCM) measurement data, the large-signal model was found to match the measurements well. A transistor model was designed containing the statistical information of the PCM data. This allows for non-linear spread analysis and reliable load-pull simulations for obtaining the highest available circuit performance. An experimental determination of the most suitable transistor geometry (i.e. number of gate fingers and gate width) and transistor bias was taken on 100 nm gate length metamorphic high electron mobility transistor (mHEMT) transistors. The most suitable combination of number of fingers, gate width and bias for obtaining maximum gain, maximum output power, and maximum power added efficiency (PAE) at a given frequency was determined.

A 160-GHz SiGe-HBT (Heterojunction Bipolar Transistor) down-conversion receiver front-end for use in active millimeter-wave imaging arrays and D-band communication applications is presented. The monolithic front-end consists of a three-stage low-noise amplifier providing 24 dB of gain and a Gilbert-cell mixer capable of operating from a −8-dBm LO signal. A fully differential architecture compatible with balanced on or off-chip antennas is used to avoid the need for on-chip baluns in antenna-integrated applications. The implemented downconversion front-end consumes 50 mA from a 3.3 V supply and requires a 0.1 mm2 die area (excl. pads) per channel. With a 160-GHz input signal and an Intermediate Frequency (IF) of 1 GHz, the implemented front-end yields a 25-dB conversion gain, a −30-dBm input compression point, and a 9-dB/7-dB (with/without auxiliary on-chip input balun) system noise figure.

This paper presents the development of a reconfigurable receiver to undertake challenging signal processing tasks for a novel polarimetric radar system. The field-programmable gate arrays (FPGAs)-based digital receiver samples incoming signals at intermediate frequency (IF) and processes signals digitally instead of using conventional analog approaches. It offers more robust system stability and avoids unnecessary multichannel calibrations of analog circuits for a full polarimetric radar. Two kinds of dual-orthogonal signals together with corresponding processing algorithms have been investigated; the digital implementation architectures for all algorithms are then presented. Processing algorithms implemented in FPGA chips can be reconfigured adaptively regarding to different transmitted waveforms without modification of hardware. The successful development of such reconfigurable receiver extends our radar capacity and thus yields tremendous experimental flexibility for atmospheric remote sensing and polarimetric studies of ground-based targets.

Multipath propagation is still one of the major problems in local positioning systems today. Especially in indoor environments, the received signals are disturbed by blockages and reflections. This can lead to a large bias in the user's time-of-arrival (TOA) value. Thus multipath is the most dominant error source for positioning. In order to improve the positioning performance in multipath environments, recent multipath mitigation algorithms based upon the concept of sequential Bayesian estimation are used. The presented approach tries to overcome the multipath problem by estimating the channel dynamics, using unscented Kalman filters (UKF). Simulations on artificial and measured channels from indoor as well as outdoor environments show the profit of the proposed estimator model. Furthermore, the quality of channel estimation applying the UKF and the channel sounding capabilities of the estimator are shown.

Near sea surface radio frequency (RF) refraction is four dimensional (4D) and can significantly impact the performance of radar systems. The refractivity field is dictated by the vertical thermodynamic structure of the constantly evolving marine atmospheric boundary layer (MABL). Logistical and budgetary restraints on meteorological measurements over water to capture the spatio-temporal structure of refractivity fields influencing radar performance have limited the knowledge of how and why radar performance is azimuth, range, and time dependent. Rapidly increasing computer processing speeds and decreasing memory capacity costs have supported the horizontal and vertical resolution requirements for mesoscale numerical weather prediction (NWP) models to resolve the thermodynamic structure in the MABL. Once modeled, refractivity structure is easily calculated from the thermodynamic structure. Mesoscale NWP models coupled with modern parabolic equation radar performance models can support the prediction of 4D radar performance in challenging non-homogeneous, near surface refractivity fields at the time and location of the modeler's choice. The NWP modeling presented in this paper demonstrates how large-scale offshore flow of warm and dry air over colder seas produces strong near surface RF trapping. Large land-sea temperature differences can produce near shore sea breezes and surface-based ducts. This paper describes modeled radar performance in such a complex ducting structure over the Persian Gulf during large-scale northwest atmospheric flow. The refractivity field was resolved by the Coupled Ocean/ Atmosphere Mesoscale Prediction System (COAMPS® is a registered trademark of the Naval Research Laboratory) and the notional radar performance was modeled by the advanced refractive effects prediction system (AREPS). The results indicate strong spatial and wavelength-dependent enhancements and degradations in radar performance relative to a standard atmosphere.

In this paper we propose a photonic technique for a reconfigurable microwave signal generation based on the beating of two laser modes coming from a regenerative fiber mode-locked laser (FMLL) into a photodiode. The excellent performance of this kind of pulsed laser guarantees high stability on the directly generated microwave signal even at ultrahigh frequencies (up to W band). Therefore, by using the proposed architecture, the performance of a reconfigurable full digital coherent radar system can be enhanced for example in terms of moving target indicator (MTI) improvement factor and analog to digital converter maximum signal to noise ratio. Differently from the conventional radar oscillators, whose performance strongly deteriorate with increasing frequencies, the photonic radio frequency (RF) generation always shows an excellent spectral purity. Moreover, thanks to the achievable high repetition rates and the coherence properties of the FMLL, this laser scheme has also been proposed for digitizing, directly at RF, the received signal by electro-optical sampling. Thus the advantage of using just one device for signal generation in both the transmitter and receiver chain, makes the proposed solution a cost-effective architecture for microwave signal generation.