To comprehensively study the physical properties of inductively coupled plasma (ICP), a finite element method (FEM) simulation model of ICP is developed using the well-established COMSOL software. To benchmark the validation of the FEM model, two key physical parameters, the electron density and the electron temperature of the ICP plasma, are precisely measured by the state-of-the-art laser Thomson scattering diagnostic approach. For low-pressure plasma such as ICP, the local pressure in the generator tube is difficult to measure directly. The local gas pressure in the ICP tube has been calibrated by comparing the experimental and simulation results of the maximum electron density. And on this basis, the electron density and electron temperature of ICP under the same gas pressure and absorbed power have been compared by experiments and simulations. The good agreement between the experimental and simulation data of these two key physical parameters fully verifies the validity of the ICP FEM simulation model. The experimental verification of the ICP FEM simulation model lays a foundation for further study of the distribution of various physical quantities and their variation with pressure and absorption power, which is beneficial for improving the level of ICP-related processes.

The plasma parameters of laser-ablated Zirconium (Zr) using a Langmuir probe technique have been investigated by employing a Q-switched Nd:YAG laser (532 nm, 6 ns) at various irradiances ranging from 8.6 to 15.5 GW/cm2. All the measurements have been performed under an ultra-high vacuum condition while keeping the probe at a fixed distance of 4 mm from the target. By varying the biasing voltages from 1 to 75 V, the corresponding values of electric currents are measured by the probe on the oscilloscope. Laser-induced Zr plasma parameters such as electron temperature, electron number density, plasma potential, Debye length, and thermal velocity have been evaluated from I–V characteristic curves of Langmuir probe data. It is found that both the electron temperature and thermal velocity of Zr plasma reveal an increasing trend from 18 to 41 eV and 2.8 × 108 to 4.3 × 108 cm/s, respectively, with increasing laser irradiance which is attributed to more energy deposition and enhanced ablation rate. However, the electron number density of Zr plasma exhibits a non-significant increase from 6.5 × 1014 to 6.7 × 1014 cm−3 with increasing irradiance from 8.6 to 10.9 GW/cm2. A further increase in irradiance from 12 to 15.5 GW/cm2 causes a reduction in the number density of Zr plasma from 6.1 × 1014 to 5.6 × 1014 cm−3 which is attributed to the formation of thick sheath, ambipolar electric field, and laser-supported detonation waves (Shock front). Scanning electron microscope analysis has been performed to reveal the surface morphology of irradiated Zr. It reveals the formation of cracks, ridges, cones, and grains. It was observed at high irradiances the ridges are vanished, whereas cones and cracks are dominant features. By controlling plasma parameters, surface structuring of materials can be controlled, which has a vast range of applications in the industry and medicine.

In this study, we have spectroscopically investigated the plasma generated by a Q-switched Nd:YAG laser operating at its fundamental wavelength of 1064 nm focused on magnesium (Mg) and titanium (Ti) target samples in the air under atmospheric pressure. We employed circular cavities of radii (2.5, 3.0, and 3.5 mm) and a square cavity to investigate the cavity confinement effect on the spectral emission intensities of the plasmas. We observed that the circular cavity of radius 2.5 mm had the maximum signal enhancement, and this can be attributed to the compression of the plasma and reheating by the reflected shock waves. The maximum enhancement factor of the Mg I-518.4 nm line was reached at approximately 3.8, 3.4, and 2.8 with a circular cavity of radius 2.5, 3.0, and 3.5 mm, respectively, at a delay time of 350 ns and a laser energy of 350 mJ. By applying varying external magnetic fields (0.47, 0.62, 0.91, and 1.23 T) across the generated plasma, the plasma parameters such as electron temperature and number density have been investigated. From our results, we observed that the radius of the cavity had a tremendous effect on the enhancement of the emission signal intensities. We also found that the increase in the electron temperature and the number density can be attributed to the increase in the applied magnetic field and the laser energy. From our calculations, the value of β, which was less than 1 for all the cases, confirms that there was a plasma confinement at the presence of the magnetic field.

In the paper, we applied the paraxial region theory and Wentzel–-Kramers–-Brillouin approximation to study laser beam self-focusing in the interaction of laser and collisional plasma with periodical density ripple. The results have shown that, under the influence of collision nonlinear effect, laser presents stable self-focusing, self-defocusing, and oscillational self-focusing in the plasma. Besides, the parameters of plasma with periodical density ripple have a greater impact on the effect of self-defocusing and oscillational self-focusing than stable self-focusing. In certain conditions, beam self-defocusing and oscillational self-focusing would decline and even disappear, and stable self-focusing would further be strengthened. Hence, selecting a suitable periodic plasma system is advantageous for separating self-defocusing and oscillational self-focusing, and for the formation of a more stable collisional self-focusing.

Self-focusing of Gaussian laser beam has been investigated in quantum plasma under the effect of applied axial magnetic field. The nonlinear differential equation has been derived for studying the variations in the beam-width parameter. The effect of initial plasma electron temperature and the axial magnetic field on self-focusing and normalized intensity are studied. Our investigation reveals that normalized intensity increases to tenfolds where quantum effects are dominant. The normalized intensity further increases to twelvefolds on increasing the magnetic field.

Spatial confinement effects on plasma parameters and surface morphology of laser-ablated Mg are studied by introducing a metallic blocker as well as argon (Ar) gas at different pressures. Nd: YAG laser at various fluences ranging from 7 to 28 J/cm2 was employed to generate Mg plasma. Confinement effects offered by metallic blocker are investigated by placing the blocker at different distances of 6, 8, and 10 mm from the target surface; whereas spatial confinement offered by environmental gas is explored under four different pressures of 5, 10, 20, and 50 Torr. Laser-induced breakdown spectroscopy analysis revealed that both plasma parameters, that is, excitation temperature and electron number density initially are strongly dependent upon both pressures of environmental gases and distances of blockers. The maximum electron temperature of Mg plasma is achieved at Ar gas pressure of 20 Torr, whereas maximum electron number density is achieved at 50 Torr. It is also observed that spatial confinement offered by metallic blocker is responsible for the significant enhancement of both electron temperature and electron number density of Mg plasma. Maximum values of electron temperature and electron number density without blocker are 8335 K and 2.4 × 1016 cm−3, respectively, whereas these values are enhanced to 12,200 K and 4 × 1016 cm−3 in the presence of blocker. Physical mechanisms responsible for the enhancement of Mg plasma parameters are plasma compression, confinement and pronounced collisional excitations due to reflection of shock waves. Scanning electron microscope analysis was performed to explore the surface morphology of laser-ablated Mg. It reveals the formation of ripples and channels that become more distinct in the presence of blocker due to plasma confinement. The optimum combination of blocker distance, fluence and Ar pressure can identify the suitable conditions for defining the role of plasma parameters for surface structuring.

The effect of the transverse magnetic field on laser-induced breakdown spectroscopy and surface modifications of germanium (Ge) has been investigated at various fluences. Ge targets were exposed to Nd: YAG laser pulses (1064 nm, 10 ns, 1 Hz) at different fluences ranging from 3 to 25.6 J/cm2 to generate Ge plasma under argon environment at a pressure of 50 Torr. The magnetic field of strength 0.45 Tesla perpendicular to the direction of plasma expansion was employed by using two permanent magnets. The emission spectra of laser-induced Ge plasma was detected by the laser-induced breakdown spectroscopy system. The electron temperature and number density of Ge plasma are evaluated by using the Boltzmann plot and stark broadening methods, respectively. The variations in emission intensity, electron temperature (Te), and number density (ne) of Germanium plasma are explored at various fluences, with and without employment of the magnetic field. It is observed that the magnetic field is responsible for significant enhancement of both excitation temperature and number density at all fluences. It is revealed that an excitation temperature increases from Te,max,without B = 16,190 to Te,max,with B = 20,123 K. Similarly, the two times enhancement in the electron density is observed from ne,max,without B = 2 × 1018 to ne,max,with B = 4 × 1018 cm−3. The overall enhancement in Ge plasma parameters in the presence of the magnetic field is attributed to the Joule heating effect and adiabatic compression. With increasing fluence both plasma parameters increase and achieve their maxima at a fluence of 12.8 J/cm2 and then decrease. In order to correlate the plasma parameters with surface modification, scanning electron microscope analysis of irradiated Ge was performed. Droplets and cones are formed for both cases. However, the growth of ridges and distinctness of features is more pronounced in case of the absence of the magnetic field; whereas surface structures become more diffusive in the presence of the magnetic field.

The influence of nature and pressure of ambient environment on the surface modification, plasma parameters, hardness, and corrosion resistance of Mg-alloy has been investigated. Nd: YAG laser (1064 nm, 10 ns, 25 mJ) at a fluence of 1.3 J cm−2 has been employed as an irradiation source. Targets of Mg-alloy were exposed in the ambient environments of argon (Ar), neon (Ne), and helium (He) at pressures ranging from 5 to 760 Torr. Scanning electron microscope has been employed to investigate the surface morphology of the irradiated targets. It reveals the formation of cavities, cones, droplets, ripples, and islands on the surface of the irradiated sample. Laser-induced breakdown spectroscopy technique was employed to measure electron temperature (Te) and electron number density (Ne) of Mg-alloy. The value of electron temperature ranges from 6628 to 12,855 K, whereas the value of electron number density varies from 5.4 × 1017 to 19.2 × 1017 cm−3. The maximum Te and Ne are observed in Ar and minimum in case of He. It was also revealed that both the surface morphology and plasma parameters are strongly dependent upon nature and pressure of environmental gases. The maxima of Te is achieved at a pressure of 10 Torr for all the three ambient environments that is, Ar, Ne, and He; whereas maxima of Ne is achieved at different pressures, that is, at 760 Torr for Ar, at 200 Torr for Ne, and at 50 Torr for He. The hardness and corrosion resistance of irradiated Mg-alloy have been explored using Vickers Micro-hardness tester and Potentio-dynamic polarization technique, respectively. It was investigated that as compared with un-irradiated target, the hardness as well as corrosion resistance of the laser-irradiated target has been increased significantly in all environments. Plasma parameters, mechanical, and electrical properties of laser-irradiated Mg-alloy have been correlated with induced surface modifications and are strongly influenced by environmental conditions.

In the paper, nonlinear structure of electromagnetic field, electron temperature, and electron density in interaction with relativistic laser and collisional underdense rippled plasma are investigated. The results are shown that due to the combination influence of relativistic effect, ohmic heating and plasma density ripple, electromagnetic field profile presents obvious asynchronism, which the peak of electric field run ahead of the peak of magnetic field. Furthermore, the electromagnetic field profiles show obvious non-sinusoidal, and the profile of electron temperature and density become highly peaked. Especially, compared with the previous work, due to the added influence of plasma density ripple, electromagnetic field, electron temperature and electron density present obvious oscillation along plasma length rather than stabilization amplitude, and their peak are out of sync.

The effect of laser-irradiance on the surface morphology and laser induced breakdown spectroscopy of zinc has been investigated by employing Nd:YAG laser (wavelength λ = 1064 nm, pulse duration t ~ 10 ns, and repetition rate = 10 Hz) under ambient environment of argon at a pressure of 20 Torr. For this purpose, zinc targets were exposed to various laser irradiances ranging from 13 GW/cm2 to 100 GW/cm2. Scanning electron microscope analysis has been performed to analyze the surface modification of irradiated zinc targets. Scanning electron microscope analysis revealed the formation of various kinds of structures such as ripples, cones, cavities, and wave like ridges at the center and peripheral regions of ablated zinc. In the central ablated region with increasing laser irradiance, the growth of distinct and well defined ripples is observed. Further increase in irradiance makes the appearance of these ripples diffusive and narrow. In order to correlate the plasma parameters with the surface modification, laser induced breakdown spectroscopy analysis has also been performed. The electron temperature and number density of zinc plasma have been evaluated at various laser irradiances. For both plasma parameters, an increasing trend up to a certain value of laser irradiance is observed which is due to enhanced energy deposition. Afterword a decreasing trend is achieved which is attributed to the shielding effect. With further increase in irradiance a saturation stage comes and almost no change in plasma parameters is observed. This saturation is explainable on the basis of the formation of a self-regulating regime near the target surface. A strong correlation between surface modification and plasma parameters is established.