This paper introduces a method to realize beam switching by using a substrate-integrated waveguide (SIW) Butler matrix combined with a slot array antenna. The Butler matrix consists of two hybrid couplers, two crossovers, two −45-degree phase shifters, and two 0-degree phase shifters. The slot array antenna is a 4 × 2 array. The operating frequency band of the slot array antenna, where the reflection coefficient is below −10 dB, is 26.5–31.5 GHz. The measured beamforming angles from input port 1 to input Port 4 of the Butler matrix are +46, −16, +15, and −50°, respectively. The corresponding antenna gains from input Port 1 to input Port 4 are 11.57 dB, 14.284 dB, 10.94 dB, and 12.864 dB, respectively. The dimensions of the Butler matrix and the slot array antenna are 56.8 mm × 21.2 mm × 0.254 mm. The dimensions of the SIW transmission channels between the Butler matrix and input Ports 1– 4 are 16.9 mm × 34 mm × 0.254 mm.

In recent years, the significance of terahertz (THz) and (sub-)THz communications has grown substantially due to its promising trade-off between higher capacity compared to microwave-based communication and better resilience against weather dependent influences (e.g., fog and rain). While electronic and optoelectronic techniques have been extensively explored, each offering distinct advantages and limitations, they have predominantly been demonstrated and discussed as individual experiments, making performance comparison challenging. This paper addresses this gap by systematically benchmarking electronic and optoelectronic signal generation approaches under comparable conditions. Our experiments incorporate various receiver types, revealing that best performance is achieved by combining optoelectronic signal generation techniques at the transmitter in combination with an all-electric intradyne receiver. This results in a remarkable line rate of 200 Gbit/s over a distance of 52 m. To our knowledge, this represents the highest line rate achieved for technically relevant transmission distances for indoor access or outdoor small cell networks.

The accuracy of electromagnetic (EM) exposure assessments depends mainly on the resolution of a voxel human body model. The resolution of the conventional human body model is limited to a few millimeters. In the millimeter wave (mmWave) frequency range, EM waves are absorbed by the superficial tissues in the human body. Therefore, resolution and skin thickness of the human body model are important for accuracy of the EM wave exposure metrics recommended by international human safety guidelines. Realistic thickness modeling of the skin tissue on the human body may provide greater accuracy in the EM exposure assessment, especially at mmWave frequency range. In this paper, effects of the skin thickness on the EM exposure metrics in one-dimensional multi-layered models obtained from different regions of the body model are investigated using the dispersive algorithm based on the finite-difference time-domain method over the frequency range from 1 to 100 GHz. Furthermore, effects of eyelid tissue in a human eye on the EM exposure metrics are studied over the frequency range. The EM exposure metrics such as absorbed power density, heating factor, and power transmission coefficient are calculated up to 100 GHz to evaluate the limits of EM wave exposure.

This paper explores the use of inkjet-printing technology for transparent transmitarrays, presenting a viable alternative to traditional copper microwire counterparts. The study focuses on achieving high-gain performance crucial for wireless communication systems, with a particular emphasis on the fifth-generation (5G) millimeter-wave communication. Transparent transmitarrays leverage transparent conducting films and conductive mesh structures, overcoming opacity limitations and seamlessly integrating with urban architecture. In this paper, the inkjet-printing process is detailed for fabricating transmitarray apertures, highlighting the flexibility and precision in depositing nanosilver particles onto a glass substrate. The design intricacies involve optimizing feeding characteristics, determining unit cell structures, and constructing transmitarrays of various sizes. To validate the proposed technique, three different apertures (15 × 15, 20 × 20, and 25 × 25 unit cells) are constructed. The antenna performances are evaluated in terms of reflection coefficients, radiation efficiency, realized gain, and patterns, demonstrating the effectiveness of inkjet-printed transmitarrays. Comparative analysis with copper microwire counterparts is also conducted, validating the inkjet-printing technology for similar gain performance with added advantages of flexibility, compatibility with transparent substrates, and cost-effective manufacturing.

This paper proposes a wideband four-element multiple-input multiple-output (MIMO) antenna operating in the millimeter-wave frequency band for 5G communications from 24.37–39.44 and 45.09–50.62 GHz. The antenna design has been realized using Rogers 5880 substrate and consists of a T-shaped strip that is attached to the top of a 50 Ω feeding line. Two microstrip lines are affixed at the terminal points of T-shaped strip and bent toward the feeding structure. These bent strip lines are then extended by joining two additional L-shaped microstrip lines. On the back, there is a partial defective ground plane featuring a rectangular slot and a thin strip line located at its center. The dimensions of the proposed single element and MIMO antenna are 0.933λ × 0.933λ × 0.024λ and 1.865λ × 1.865λ × 0.024λ, respectively (at 28 GHz), while the edge-to-edge distance between the radiation elements of the MIMO antenna is 4.0 mm. The design incorporates an efficient passive fan-shaped decoupling structure to decrease coupling between antenna elements. Simulations and experimental results show good agreement with each other. For all resonant frequencies the measured peak gain is greater than 4.85 dBi, radiation efficiency is over 90%, diversity gain is greater than 9.5, ECC is less than 0.025, TARC is less than -10 dB and CCL is below 0.4 bits/s/Hz. The proposed MIMO antenna, with its wide bandwidth, high gain, high inter-port isolation, and high efficiency characteristics, can be used for 5G wireless communication applications.

The 5th generation new radio (5G NR) standards create both enormous challenges and potential to address the spatio-spectral-temporal agility of wireless transmission. In the framework of a research unit at TU Ilmenau, various concepts were studied, including both approaches toward integrated circuits and distributed receiver front-ends (FEs). We report here on the latter approach, aiming at the proof-of-principle of the constituting FEs suitable for later modular extension. A millimeter-wave agile multi-beam FE with an integrated 4 by 1 antenna array for 5G wireless communications was designed, manufactured, and verified by measurements. The polarization is continuously electronically adjustable and the directions of signal reception are steerable by setting digital phase shifters. On purpose, these functions were realized by analog circuits, and digital signal processing was not applied. The agile polarization is created inside the analog, real-time capable FE in a novel manner and any external circuitry is omitted. The microstrip patch antenna array integrated into this module necessitated elaborate measurements within the scope of FE characterization, as the analog circuit and antenna form a single entity and cannot be assessed separately. Link measurements with broadband signals were successfully performed and analyzed in detail to determine the error vector magnitude contributions of the FE.

Next-generation automotive radar sensors are increasingly becoming sensitive to cost and size, which will leverage monolithically integrated radar system-on-Chips (SoC). This article discusses the challenges and the opportunities of the integration of the millimeter-wave frontend along with the digital backend. A 76–81 GHz radar SoC is presented as an evaluation vehicle for an automotive, fully depleted silicon-over-insulator 22 nm CMOS technology. It features a digitally controlled oscillator, 2-millimeter-wave transmit channels and receive channels, an analog base-band with analog-to-digital conversion as well as a digital signal processing unit with on-chip memory. The radar SoC evaluation chip is packaged and flip-chip mounted to a high frequency printed circuit board for functional demonstration and performance evaluation.

This paper presents a comparison of chip connections using aerosol jet (AJ) and bond technology on low-cost printed circuit board (PCB) substrates. First, the behavior of the used gap filler material and the used silver ink for AJ technology on PCBs are characterized. In addition to comparing the radio frequency (RF) performance (DC to 67 GHz) of the two technologies, the mechanical stability is also compared. While the AJ technology transitions score above all for their RF performance and the lower requirements (surface finish, pad size, and adhesion) on the PCB, the bonding technology has clear advantages, especially with a different coefficient of thermal expansion values of the substrates to be connected. Finally, the measurement results of a complete package are shown, whereby the chip connection is realized once by means of AJ and once by bonding wires.

We address transmission between array antennas in the Fresnel region, where there is a difference between the theoretical and actual transmission efficiencies. In particular, we focus on the effect of synthesis loss in the receiving antenna's power combiner circuit caused by amplitude and phase differences among the signals received by the elements. We designed 24 GHz array antennas and investigated the effect of synthesis loss on transmission efficiency via simulation. The synthesis loss was found to increase for smaller transmitting antenna sizes and larger receiving antenna sizes. In addition, to clarify the origin of the discrepancy between the theoretical and actual efficiency values and accurately estimate the efficiency, we defined four other loss factors and calculated them via simulation. Based on the results obtained, we propose an approximate equation for transmission efficiency in terms of synthesis loss and aperture efficiency. Finally, we calculate the efficiency with the effect of the loss factors included and confirm that the calculated and measured efficiencies are almost identical.

Demands for very high-speed wireless communication access is rapidly growing with respect to the increasing data rates for the use of rich multimedia content in various applications of defense, enterprise, industrial, and public domains. To serve these gigabit fidelity (Gi-Fi) uses for various wireless applications, millimeter wave (MmW) wireless technology with huge bandwidth in licensed/unlicensed bands is triggering boundless avenues. In this research, the concept of substrate-integrated waveguide (SIW) and exponentially tapered slot (ETS) antenna are used together design a high-gain, efficient planar dielectric-loaded antenna for MmW-based Gi-Fi wireless communications using unlicensed 60 GHz band in the MmW family. The SIW is used to feed the antenna and a dielectric is utilized increasing the gain. The dielectric-loaded ETS antenna and compact SIW feed are fabricated on a single substrate, resulting in low cost and easy fabrication utilizing printed circuit board process. The measured gain of single-element antenna is 11.4 dB, with radiation efficiency of 96.84% at 60 GHz. Then indoor radio wave propagation studies are carried out using elliptically dielectric-loaded ETS antenna with radio frequency measurement equipment to measure and model propagation channels at 60 GHz. The attained simulations are compared with the experimental results.

In this work, the possibility of achieving GaN-on-Si devices for millimeter wave applications operating at high bias is demonstrated. It is shown that highly scaled AlN/GaN-on-Si double heterostructure enables us to significantly improve electron confinement under high electric field as compared to single heterostructure while delivering high carrier density (>2 × 1013 cm−2). Subsequently, trapping effects can be minimized resulting in the highest GaN-on-Si output power density up to 40 GHz and at a drain bias of 15 V together with a record fmax close to 200 GHz. At higher bias, infrared camera analysis clearly shows that these devices are mainly limited by self-heating effects. Furthermore, low noise figure has been assessed on this heterostructure, promising integration of cost effective low noise and high power millimeter wave amplifiers.

This study deals with a non-exhaustive overview of location systems operating in the 60 GHz frequency band. Both impulse and frequency hopping topologies are considered and the performances of the two realized systems are presented. For each system, a specific signal processing has been implemented to prevent the degradation of the location error from the impact of the multipath propagation.

This paper proposes a receiver that repeats iterative frequency-domain equalization (FDE) and decision-directed phase noise compensation (DD-PNC) to alleviate degradation due to the phase noise for millimeter-wave single carrier (SC) systems. High bit-rate SC-FDE transceivers based on the single-chip Si RF-CMOS IC technology in the 60-GHz millimeter-wave band have been extensively studied for wireless personal area network (WPAN) systems, and the relatively large phase noise in a phase-locked loop (PLL) synthesizer severely degrades transmission performance. In an initial processing of the proposed receiver, a cyclic prefix (CP)-based phase noise compensator (CP-PNC) removes the phase noise from a time-domain received signal by using CP, which is known to the receiver, and the channel is equalized by the iterative FDE using the conventional minimum mean-square-error (MMSE) weight. In an iterative processing, DD-PNC estimates the phase noise each symbol by exploiting an output of a channel decoder, and then compensates the time-domain received signal for the phase noise by using the estimate. In order to equalize the compensated received signal, the iterative FDE performs both the MMSE filtering and residual inter-symbol interference cancelation using the decoder output. Computer simulations following the 60-GHz WPAN standard demonstrate that in the 64QAM with the coding rate of 3/4, the proposed receiver with three iterations can drastically remove the phase noise of −85 dBc/Hz at 1 MHz offset, and that it can achieve excellent transmission performance.

The use of digital predistortion for linearizing a millimeter-wave power amplifier (PA) is investigated. A PA operating at 38 GHz is designed using an accurate non-quasi-static transistor model, taking into account both short- and long-term memory effects. A realistic test signal is then used for the identification of a nonlinear auto-regressive moving average (NARMA) behavioral model of the PA. The NARMA-based digital predistorter is then derived and formulated in terms of basic predistortion cells, especially suitable for efficient implementation in an FPGA. The performance of the predistortion solution is preliminarily assessed by means of computer simulations.

Four existing millimeter arrays have been very productive in the last few years and are currently being expanded in their capabilities. Recent technical developments in these arrays as well as the prospects for submillimeter interferometry and larger arrays are presented.