Hostname: page-component-cd9895bd7-fscjk Total loading time: 0 Render date: 2024-12-28T21:41:41.518Z Has data issue: false hasContentIssue false
  • English
  • Français

An Experimental Study of a Symmetrical Aerofoil with a Rear Suction Slot and a Retractable Flap

Published online by Cambridge University Press:  28 July 2016

D. M. Heughan
D. M. Heughan*
Affiliation:
Cambridge University Aeronautics Laboratory, now at The British Rubber Producers' Research Association
Get access Rights & Permissions [Opens in a new window]

Summary

Experiments were made on an aerofoil of 25 per cent, thickness with a suction slot at the rear and a flap that could be withdrawn into the slot. The main object of the work was to investigate the effect of withdrawing the flap when all the air in the boundary layer was sucked into the slot. In particular, as a test of the type of anti-gust device proposed by Thwaites, it was required to observe the change of lift that occurred during withdrawal of the flap and a subsequent change of incidence (with the flap still withdrawn).

The flow was investigated by the use of smoke and tufts, by pressure plotting on the surface of the aerofoil, and by measurements of total and static pressures in the wake. The effects of varying incidence, flap position, and suction velocity were investigated.

It was found that the provision of a flap downstream of the enclosing streamline, so that the rear stagnation point was not in the free fluid, was all important in relation to the behaviour of an aerofoil which had a suction slot at its rounded rear.

With the flap extended beyond the enclosing streamline and with the ratio of suction-slot velocity to free stream velocity higher than the theoretical value, a stable flow was obtained within the theoretical incidence range. A favourable pressure gradient was observed in the slot entry and no measureable wake existed downstream of the flap. Smoke filaments, emitted from a tube projecting from the slot slightly beyond the enclosing streamline, travelled far downstream with apparently little diffusion.

When the flap was placed so that its trailing edge was inside the enclosing streamline, i.e. so that there was in theory a stagnation point in the free fluid, an instability of a three-dimensional character occurred, with a wide wake and a large drag coefficient. The lift curves were unusual and it was found that movement of the flap caused a large change of lift coefficient. There was no evidence that the lift could be maintained constant, independent of incidence, when the flap was withdrawn into the slot.

Type
Research Article
Information
The Aeronautical Journal , Volume 57 , Issue 514 , October 1953 , pp. 627 - 645
Copyright
Copyright © Royal Aeronautical Society 1953

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Thwaites, B. (1948). The Production of Lift Independently of Incidence. Journal of the Royal Aeronautical Society, February 1948. R. & M. 2611 and 2612. 1947.Google Scholar
2. Thwaites, B. (1947). Interim Note on Experiments on a Thwaites Flap fitted to a Circular Cylinder. A.R.C. 11,023. (R. & M. 2611).Google Scholar
3. Preston, J. H. (1950). The Steady Circulatory Flow about a Circular Cylinder with uniformly Distributed Suction at the Surface. The Aeronautical Quarterly, February 1950.Google Scholar
4. Preston, J. H. (1950). Non-Steady Flows under Asymptotic Suction Conditions. Quarterly Journal of Mechanics and Applied Mathematics, Vol. 3, Part 4, 1950.Google Scholar
5. Lighthill, M. J. (1945). A New Method of Two-Dimensional Aerodynamic Design. R. & M. 2112, April 1945.Google Scholar
6. Regenscheit, B. (1947). Tests on a Wing with Suction at the Trailing Edge. A.R.C. 11,388.Google Scholar
7. Stüper, I. (1950). Flight Experiences and Tests on Two Airplanes with Suction Slots. N.A.C.A. T.M. 1232.Google Scholar
8. Smith, C. B. (1949). A Solution for the Lift and Drag of Aerofoils with Air Inlets and Suction Slots. Journal of the Aeronautical Sciences, October 1949.Google Scholar
9. Rawcliffe, A. G. (1947). Suction Slot Ducting Design. A.R.C. 9487 and 10,522. (R. & M. 2580).Google Scholar
10. Preston, J. H. (1950). The Three-Quarter Radius Pitot Tube Flow Meter. The Engineer, October 1950.Google Scholar
11. SirMelvill, Jones (1936). Measurement of Profile Drag by the Pitot Traverse Method. R. & M. 1688.Google Scholar
12. Glauert, H. (1933). Wind Tunnel Interference on Wings, Bodies and Airscrews. R. & M. 1566, September 1933.Google Scholar
13. Pankhurst, R. C. and Thwaites, B. (1950). Experiments on the Flow Past a Porous Circular Cylinder Fitted with a Thwaites Flap. A.R.C. 13,447.Google Scholar
14. Pankhurst, R. C. and Walker, W. S. (1950). Smoke Visualisation of Flow Past Circular Cylinder with Thwaites Flap. A.R.C. 13,507.Google Scholar
15. Pfenninger, W. (1947). Investigations on Reductions of Friction on Wings, in particular by means of Boundary Layer Suction. N.A.C.A. T.M. 1181.Google Scholar
16. Gregory, N., Pankhurst, R. C. and Walker, W. S. (1950). Wind Tunnel Tests on the Prevention of Boundary Layer Separation by Distributed Suction at the Rear of a Thick Aerofoil. A.R.C. 13,446.Google Scholar
17. Prandtl, L. and Tietjens, O. G. (1934). Applied Hydro and Aero-mechanics, pp. 82–85 and pp. 280-287, McGraw Hill, 1934.Google Scholar
18. Goldstein, S. (Editor) (1938). Modern Developments in Fluid Dynamics, Vol. I, pp. 81–84, and Vol. II, pp. 545–549, Clarendon Press.Google Scholar