Hostname: page-component-cd9895bd7-jkksz Total loading time: 0 Render date: 2024-12-28T06:11:50.717Z Has data issue: false hasContentIssue false
  • English
  • Français

On the design of three-dimensional wind tunnel contractions

Published online by Cambridge University Press:  04 July 2016

J. H. Downie ,
R. Jordinson  and
F. H. Barnes
J. H. Downie
Affiliation:
Department of Mechanical & Production Engineering, Brighton Polytechnic
R. Jordinson
Affiliation:
Department of Mechanical & Production Engineering, Brighton Polytechnic
F. H. Barnes
Affiliation:
Department of Mechanical & Production Engineering, Brighton Polytechnic
Get access Rights & Permissions [Opens in a new window]

Extract

A method is given for the calculation of incompressible inviscid flow through non-axisymmetric contracting ducts with rectangular cross-sections. The method is based on a finite difference approximation to Laplace's equation and solved by the method of successive over relaxation. In an attempt to provide practical criteria for the design of such contractions, the flows through a series of contraction shapes were calculated, each shape being based on a pair of matched elliptic arcs. This permitted choice of such parameters as length, local (ie two-dimensional) contraction ratio, position and magnitude of the maximum slope. It was found that reducing the length of the contraction also reduced its effective length, although increasing the effects of overshoot and undershoot. This could be compensated for by designing a contraction with a steep maximum slope which with associated low curvatures at entrance and exit reduced the values of overshoot and undershoot. The axial positions of maximum slope on wall and roof should be the same.

The predictions of the numerical method were tested against experiment and, in general, satisfactory comparisons were obtained.

Type
Research Article
Information
The Aeronautical Journal , Volume 88 , Issue 877 , February 2001 , pp. 287 - 295
Copyright
Copyright © Royal Aeronautical Society 1984 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Morel, T. Comprehensive Design of Axisymmetric Wind Tunnel Contractions, Journal of Fluids Engineering, Trans, of the ASME, June 1975, 97, 225.Google Scholar
2. Whitehead, L. G., Wu, L. Y. and Waters, M. H. L. Contracting ducts of finite length, Aeronautical Quarterly, Febuary l951, 2, 254.Google Scholar
3. Gibbings, J. C., and Dixon, J. R. Two-dimensional contracting duct flow. Quarterly Journal of Mechanics and Applied Mathematics 1951, 10, part 1.Google Scholar
4. Jordinson, R. Design of wind tunnel contractions. Aircraft. Engineering, October 1961, 294.Google Scholar
5. Jordinson, R. and Rodger, J. G. On an approximation to the flow through axisymmetric contracting ducts. Aeronautical Quarterly, February 1981, 32, 72.Google Scholar
6. Stratford, B. S. The Prediction of Separation of the Turbulent Boundary Layer. Journal of Fluid Mechanics, 1959, 5, 1.Google Scholar
7. Hess, J. L. and Smith, A. M. O. Calculation of potential flow about arbitrary bodies. Progress in Aeronautical Sciences. (Editor, Küchemann, D.), 1967, 8. Pergamon Press.Google Scholar
8. Rodger, J. G. Design of wind tunnel contractions. PhD thesis, Edinburgh University, 1976.Google Scholar
9. Argyris, J. H. and Maraczek, G. Potential Flow Analysis by finite elements. Ing Arch Bd42. H. l (1972), 1.Google Scholar
10. Varga, R. S. Matrix Iterative Analysis. Prentice-Hall, Series in Automatic Computation, New Jersey, 1962, 182.Google Scholar
11. Bryer, D. W. and Loveday, M. S. Considerations on the design of non-axisymmetric contractions of low area ratios. NPL Environment Report, 1970.Google Scholar
12. Downie, J. H. and Barnes, F. H. A small wind tunnel made of polystyrene. Phys Educ, 1979, 14, 112.Google Scholar