Propulsion airframe integration design and analysis has many challenges as we move into the 21st century. Along with the conventional challenges of integrating a propulsion system on an aircraft, new technologies and new business drivers dictate innovative approaches to the design process be developed and applied.

On the technical side, new innovations in jet noise suppression and new aircraft concepts such as the blended wing body (BWB) will give rise to many challenges in propulsion system performance, operability, and meeting system requirements such as thrust reverse capability. Aircraft engine and aircraft manufacturers must have the appropriate design and analysis tools in place which provide the ability to react quickly to inevitable design changes, driven by constantly changing requirements, during the product development cycle.

On the business side, the rapid globalisation of the business dictates that the latest electronic technology be utilised to enable speed in communication with global customers as well as revenue sharing partners. More than ever, cost and schedules dictate the use of analytical methods to minimise the amount of qualification testing. Design and analysis software must be flexible and capable of integrating CAD/CAM and CAE tools while maintaining configuration control of the product.

The following paper describes some of the new technical challenges facing the industry. Innovative methods of addressing those challenges are described.

This paper briefly considers the method of simulating gunfire damage to a wing and outlines the key basic assumptions used in modelling. The results of qualitative and quantitative investigations into the aerodynamic characteristics of a wing damaged at quarter chord are then presented. The results are discussed in terms of flow mechanisms, changes to surface pressure distributions and increments in lift, drag and pitching moment coefficients. For the damaged wing, the influence on force and moment coefficients was attributed to flow through the damage. This through flow was driven by the pressure differential between the upper and lower wing surfaces, and took one of two forms. The first form was a ‘weak-jet’ which formed an attached wake and resulted in small changes in force and moment coefficients. The second form resulted from either increased incidence, or damage size. This was the ‘strong-jet’, where through flow penetrated into the freestream flow, resulting in separation of the oncoming surface flow, and the development of a larger separated wake with reverse flow. The effect on force and moment coefficients was significant. The paper also compares the structure of the damage through flow with previously published results for jets in crossflows. Many similarities in the flow features were identified, although there were significant differences in the surface pressure distributions for the two cases.

The NASA tetrahedral unstructured software system (TetrUSS) was developed during the 1990s to provide a rapid aerodynamic analysis and design capability to applied aerodynamicists. The system comprises of loosely integrated, user-friendly software that enables the application of advanced Euler and Navier-Stokes tetrahedral finite volume technology to complex aerodynamic problems. TetrUSS has matured well because of the generous feedback from many willing users representing a broad cross-section of background and skill levels. This paper presents an overview of the current capabilities of the TetrUSS system along with some representative results from selected applications.

This paper addresses the problem of the complex nature of low velocity impact damage in fabricated structures made of laminated carbon-epoxy composites. The structures chosen are stiffened compression panels since these are the most vulnerable to delamination and debonding. Four ‘top-hat’ stiffened panels were tested and predicted using a dynamic finite element code. The panels all had considerable postbuckling strength so the impact sites were carefully chosen to inflict maximum loss of strength. It was shown that the threshold energy for onset of delamination can be predicted using a dynamic finite element code. The amount of delamination or debonding is also predicted using a crude strength-based criterion, which seems to work only because the maximum impact force is a transient phenomenon of short duration.

Over the past three decades, the UK aerospace industry has carried out significant research into the development of short take-off and vertical landing (STOVL) technology, to enhance the performance and operation of the Harrier aircraft, and for possible application to future aircraft such as those being developed under the Joint Strike Fighter (JSF) programme. Some of this research has focused on aircraft handling and flight control for the transition between wing-borne and jet-borne flight. Following on from internal research at British Aircraft Corporation/British Aerospace (now part of BAE Systems) in the mid to late 1970s, further development work has been carried out in the 1980s and 90s in support of the UK’s Vectored thrust Advanced Aircraft flight Control (VAAC) Harrier and Integrated Flight and Propulsion Control System (IFPCS) programmes. This paper contains a short review of STOVL aircraft longitudinal flight control law design, and how basic feedback control schemes can be used to influence the aircraft’s response and hence its handling qualities.

The aviation industry plays a critical role in modern society, supporting global, regional and local economies and facilitating long distance travel for business and leisure. However the environmental impact of the industry is significant and this threatens the sustainability of future growth and the consequential benefits which could arise from it. Technological, operational and infrastructure improvements designed to reduce emissions and noise from aircraft are continually being eroded by the rapid growth of the industry, with the result that the environmental impact of air travel is increasing. Consequently, the sustainable development of the aviation industry will require that in future, technological innovation and fleet replacement continues at a rapid pace and that the highest priority is given to achieving a ‘step change’ in aircraft technology.

This paper outlines the development of flight simulators used in civil training, military training and in engineering simulation. It describes the evolution of flight simulators and the typical architecture of a modern flight simulator. The technical innovations, which have occurred in modelling, motion systems and visual systems are reviewed. The paper also reviews the transfer of training in flight simulation, the application of simulation to engineering design and outlines problems which are encountered in flight simulation. The paper concludes by reviewing the current trends in flight simulation.

The present paper addresses the problem of extracting indicial response functions from solutions of the Navier-Stokes equations. Two approaches are considered.

In the first, the indicial response is computed directly by modifying the local grid velocity to reflect the step change in plunge velocity. The computed data are then fitted using an assumed form for the response function and numerical optimisation techniques.

In the second (indirect) approach, the general form of the lift transfer operator is determined analytically from the functional form of the assumed response. Using the lift transfer operator explicit solutions of the in-phase and quadrature components of the normal force time history can be obtained. The unknown coefficients in the response function are then extracted from computed data for harmonic motion by fitting the time history using the explicit solution.

Computed response functions are presented for a range of Mach numbers and are compared with analytical results and indicial models currently used within the rotorcraft community. For the cases considered there is no significant difference between the response functions determined using the direct or indirect approach. Comparison of the computed results with existing models suggests that generalisation of the response to step changes in incidence using a two-pole approximation of the circulatory response together with the Prandtl-Glauert factor is not possible. However, comparison with higher order semi-empirical models is much improved, providing some justification for the use of such models. In addition to these observations, the extracted response functions suggest improvements to piston theory to account for thickness effects. The proposed modification of piston theory is based upon properties of the static pressure distribution and so can be used in conjunction with both CFD and experimental data.