Hostname: page-component-78c5997874-t5tsf Total loading time: 0 Render date: 2024-11-10T19:31:28.119Z Has data issue: false hasContentIssue false
  • English
  • Français

Design of dual/tri-frequency impedance transformer with ultra-high transforming ratio

Published online by Cambridge University Press:  29 September 2017

Rusan Kumar Barik  and
S. S. Karthikeyan
Rusan Kumar Barik*
Affiliation:
Indian Institute of Information Technology Design & Manufacturing Kancheepuram, Chennai 600127, India
S. S. Karthikeyan
Affiliation:
Indian Institute of Information Technology Design & Manufacturing Kancheepuram, Chennai 600127, India
*
Corresponding author: R. K. Barik Email: edm15d003@iiitdm.ac.in
Get access Rights & Permissions [Opens in a new window]

Abstract

In this article, the design of a new dual-band impedance transformer with ultra-high transforming ratio (UHTR) is presented. The closed-form expressions are derived analytically using a lossless transmission-line theory. To practically validate the proposed design concept, two examples of dual-band transformer working at smaller and larger frequency ratios are designed for different load impedance of 500, 1000, and 1500 Ω. Finally, three prototypes of dual-band transformer with UHTR are designed, fabricated, and tested. For all these prototypes, different frequency ratios (two operating frequencies can be chosen arbitrarily) are considered. The measured return loss of the prototypes is better than 15 dB at all the operating frequencies. The measured results are matched very closely with the simulated results. This design is then extended to match a complex load at two different frequencies. The multi-band characteristic is obtained by decomposing a shorted stub into a stepped impedance section of the proposed structure. With the necessary derivation and analysis, a tri-frequency matching network is designed for a transforming ratio of 10.

Keywords

Passive components and circuitsComputer-aided designModelingSimulation and characterizations of devices and circuits
Type
Research Papers
Information
International Journal of Microwave and Wireless Technologies , Volume 9 , Issue 10 , December 2017 , pp. 1951 - 1960
Copyright
Copyright © Cambridge University Press and the European Microwave Association 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Sun, H.; Guo, Y.X.; He, M.; Zhong, Z.: A dual-band rectenna using broadband Yagi antenna array for ambient RF power harvesting. IEEE Antennas Wireless. Propag. Lett., 12 (2013), 918–921.Google Scholar
[2] Yang, X.X.; Jiang, C.; Elsherbeni, A.Z.; Yang, F.; Wang, Y.Q.: A novel compact printed rectenna for data communication systems. IEEE Trans. Antennas Propag., 61 (2013), 2532–2539.Google Scholar
[3] Chuang, M.L.: Dual-band impedance transformer using two-section shunt stubs. IEEE Trans. Microw. Theory Tech., 58 (2010), 1257–1263.Google Scholar
[4] Nikravan, M.A.; Atlasbaf, Z.: T-section dual-band impedance transformer for frequency-dependent complex impedance loads. Electron. Lett., 47 (2011), 551–553.Google Scholar
[5] Manoochehri, O.; Asoodeh, A.; Forooraghi, K.: Pi -model dual-band impedance transformer for unequal complex impedance loads. IEEE Microw. Wireless Compon. Lett., 25 (2015), 238–240.Google Scholar
[6] Barik, R.K.; Bishoyi, P.K.; Karthikeyan, S.S.: Design of a novel dual-band impedance transformer, in Proc. IEEE Int. Conf. on Electronics, Computing and Communication Technologies (CONECCT), 2015, 1–4.Google Scholar
[7] Chuang, M.L.; Wu, M.T.: General dual-band impedance transformer with a selectable transmission zero. IEEE Trans. Compon. Packag. Manuf. Technol., 6 (2016), 1113–1119.Google Scholar
[8] Barik, R.K.; Siddiqui, R.; Kumar, K.V.P.; Karthikeyan, S.S.: Design of a novel dual-band low noise amplifier incorporating dual-band impedance transformer, in Proc. Int. Conf. on Signal Processing and Communications (SPCOM), 2016, 1–5.CrossRefGoogle Scholar
[9] Maktoomi, M.A.; Hashmi, M.S.; Ghannouchi, F.M.: Improving load range of dual-band impedance matching networks using load-healing concept. IEEE Trans. Circuits Syst. II: Express Briefs, 64 (2017), 126–130.Google Scholar
[10] Rawat, K.; Ghannouchi, F.M.: Dual-band matching technique based on dual-characteristic impedance transformers for dual-band power amplifiers design. IET Microw. Antennas Propag., 5 (2011), 1720–1729.Google Scholar
[11] Chow, Y.L.; Wan, K.L.: A transformer of one-third wavelength in two sections - for a frequency and its first harmonic. IEEE Microw. Wireless Compon. Lett., 12 (2002), 22–23.CrossRefGoogle Scholar
[12] Monzon, C.: Analytical derivation of a two-section impedance transformer for a frequency and its first harmonic. IEEE Microw. Wireless Compon. Lett., 12 (2002), 381–382.Google Scholar
[13] Monzon, C.: A small dual-frequency transformer in two sections. IEEE Trans. Microw. Theory Tech., 51 (2003), 1157–1161.CrossRefGoogle Scholar
[14] Orfanidis, S.J.: A two-section dual-band Chebyshev impedance transformer. IEEE Microw. Wireless Compon. Lett., 13 (2003), 382–384.Google Scholar
[15] Wang, X.; Ohira, M.; Ma, Z.: A flexible two-section transmission-line transformer design approach for complex source and real load impedances. IEICE Electron. Express, 14 (2017), 20161095–20161095.Google Scholar
[16] Wang, X.; Ma, Z.; Sakagami, I.; Mase, A.; Yoshikawa, M.: Small, single-band, two-section transformer for real load impedances with symmetry property. Electron. Lett., 52 (2016), 934–936.Google Scholar
[17] Nguyen, H.T.; Ang, K.S.; Ng, G.I.: Design of coupled three-line impedance transformers. IEEE Microw. Wireless Compon. Lett., 24 (2014), 84–86.Google Scholar
[18] Ang, K.S.; Lee, C.H.; Leong, Y.C.: Analysis and design of coupled line impedance transformers, in IEEE MTT-S Int. Microwave Symp. Digest, vol. 3, 2004, 1951–1954.Google Scholar
[19] Chen, M.G.; Hou, T.B.; Tang, C.W.: Design of planar complex impedance transformers with the modified coupled line. IEEE Trans. Compon. Packag. Manuf. Technol., 2 (2012), 1704–1710.Google Scholar
[20] Ehsan, N.; Hsieh, W.T.; Moseley, S.H.; Wollack, E.J.: Broadband planar 5:1 impedance transformer. IEEE Microw. Wireless Compon. Lett., 25 (2015), 636–638.Google Scholar
[21] Kim, P.; Chaudhary, G.; Jeong, Y.: Enhancement impedance transforming ratios of coupled line impedance transformer with wide out-of-band suppression characteristics. Microw. Opt. Technol. Lett., 57 (2015), 1600–1603.Google Scholar
[22] Kim, P.; Chaudhary, G.; Jeong, Y.: Ultra-high transforming ratio coupled line impedance transformer with bandpass response. IEEE Microw. Wireless Compon. Lett., 25 (2015), 445–447.Google Scholar
[23] Wu, Q.S.; Zhu, L.: Short-ended coupled-line impedance transformers with ultrahigh transforming ratio and bandpass selectivity suitable for large load impedances. IEEE Trans. Compon. Packag. Manuf. Technol., 6 (2016), 767–774.Google Scholar
[24] Barik, R.K.; Karthikeyan, S.S.: A novel quad-band impedance transformer with ultra-high transforming ratio. Int. J. Electron. Commun., 78 (2017), 157–161.Google Scholar
[25] Barik, R.K.; Karthikeyan, S.S.: A novel design of ultra-high impedance transforming ratio quad-band matching network. Microw. Opt. Technol. Lett., 59 (2017), 2021–2026.Google Scholar
[26] Pozar, D.M.: Microwave Engineering, Wiley, New York, 2005.Google Scholar