Hostname: page-component-78c5997874-s2hrs Total loading time: 0 Render date: 2024-11-10T08:48:44.789Z Has data issue: false hasContentIssue false
  • English
  • Français

A programmable compact wide-band RF feed network

Published online by Cambridge University Press:  18 March 2014

Mohammad S. Sharawi ,
Sameir E. Deif ,
Elias Ghafari  and
Daniel N. Aloi
Mohammad S. Sharawi*
Affiliation:
Department of Electrical Engineering, King Fahd University of Petroleum and Minerals (KFUPM), Dhahran, 31261, Saudi Arabia. Phone: +966 13 860 4810
Sameir E. Deif
Affiliation:
Department of Electrical Engineering, King Fahd University of Petroleum and Minerals (KFUPM), Dhahran, 31261, Saudi Arabia. Phone: +966 13 860 4810
Elias Ghafari
Affiliation:
Department of Electrical and Computer Engineering, Oakland University, Rochester, MI 48309, USA
Daniel N. Aloi
Affiliation:
Department of Electrical and Computer Engineering, Oakland University, Rochester, MI 48309, USA
*
Corresponding author: M.S. Sharawi Email: msharawi@kfkupm.edu.sa
Get access Rights & Permissions [Opens in a new window]

Abstract

The design and fabrication of a wide-band programmable radio frequency (RF) feed network is proposed. It is designed to cover a wide band from 2.5 to 6 GHz over two separate branches. The feed network is simulated and fabricated on an FR-4 substrate with 0.8 mm thickness. Good matching between simulation and measurement results is achieved. The measured amplitude resolution was 0.5 dB with a maximum error of 0.22 dB. The measured phase resolution was approximately 5.6° with 1° maximum error. This design is a generic one that can be used in any kind of RF or antenna systems.

Keywords

Feed networkBroad-bandProgrammableAntennas
Type
Research Papers
Information
International Journal of Microwave and Wireless Technologies , Volume 7 , Issue 1 , February 2015 , pp. 37 - 43
Copyright
Copyright © Cambridge University Press and the European Microwave Association 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1]Butler, J.; Howe, R.: Beamforming matrix simplifies design of electronically scanned antennas. Electron. Design, 9 (1961), 170–173.Google Scholar
[2]Solbach, K.; Angenendt, S.: Four-square phased array for multi-beam applications using novel matrix feed, in Eur. Radar Conf., 2007, 358–361.Google Scholar
[3]Chang, C.-C.; Chin, T.-Y.; Wu, J.-C.; Chang, S.-F.: Novel design of a 2.5-GHz fully integrated CMOS Butler matrix for smart-antenna systems. IEEE Trans. Microw. Theory Techn., 56 (8) (2008), 1757–1763.Google Scholar
[4]Chang, C.-C.; Lee, R.-H.; Shih, T.-Y.: Design of a beam Switching/Steering Butler matrix for phased array system. IEEE Trans. Antennas Propag., 58 (2) (2010), 367–374.Google Scholar
[5]Hutu, F.; Cordeau, D.; Paillot, J.M.: 2.4 GHz antenna array using vector modulator based active phase shifters for beamforming. IET Microw. Antennas Propag., 5 (2) (2011), 245–254.CrossRefGoogle Scholar
[6]Yu, T.; Rebiez, G.: A 24 GHz 6-bit CMOS phased-array receiver. IEEE Microw. Wireless Compon. Lett., 18 (6) (2008), 422–424.Google Scholar
[7]Rotman, W.; Franchi, P.: Cylindrical microwave lens antenna for wideband scanning applications. Int. Symp. Antennas and Propagation, vol. 18 (1980), 564–567.Google Scholar
[8]Thomas, D.: Multiple beam synthesis of low sidelobe patterns in lens fed arrays. Int. Symp. Antennas and Propagation, vol. 15 (1977), 181–184.Google Scholar
[9]Lin, H.-I.; Liao, W.-J.: A beam switching array based on Rotman lens for MIMO technology. Int. Conf. Microwave and Millimeter Wave Technology, vol. 2 (2012), 1–4.Google Scholar
[10]Rahimian, A.; Rahimian, A.: Enhanced RF steerable beamforming networks based on Butler matrix and Rotman lens for ITS applications, in Int. Conf. Comp. Tech. in Electrical and Electronics Engineering, 2010, 567–572.Google Scholar