This paper proposes an air-filled substrate integrated waveguide (AFSIW) bandpass filter with a miniaturized non-resonant node (NRN). The NRN structure is introduced between the three resonators, and its size is smaller than the resonator size, which can realize the NRN structure’s miniaturization and reduce the model’s size. The NRN size of this filter is 41% of the NRN size of the existing AFSIW filter. This filter also introduces a transmission zero (TZ) above the passband. The measured results show that the filter’s center frequency is 20.73 GHz, and the bandwidth is 0.86 GHz. The insertion loss in the passband is 0.95 dB, and the return loss is better than 23 dB. Due to the TZ in the upper stopband, the AFSIW filter obtained good selectivity.

This paper presents a design methodology for a broadband high-efficiency power amplifier (PA). The large available impedance space of the extended continuous Class-GF mode is employed. A novel output matching network of the PA consisting of a rectangular double transmission line structure is proposed to meet impedance requirements. To validate the effectiveness of this structure, a high-efficiency PA operating in 0.8–3.0 GHz is designed using a CGH40010F GaN transistor. The measured results demonstrate that the drain efficiency falls within the range of 63.2%–71.9%, the output power varies from 40.2 to 42.2 dBm, and the gain ranges from 9.4 to 11.3 dB within the frequency band of 0.8–3 GHz. The realized PA exhibits an extremely competitive relative bandwidth of 115.8%.

A multiresonance metasurface antenna is proposed which has wide bandwidth and low-profile. The characteristic mode theory is used to design antenna structure. Three ideal modes are obtained by adjusting the mode currents to optimize the radiation performance of the antenna. The characteristic mode analysis is used to model, analyze, and optimize the antenna, revealing the physical characteristics of the metasurface antenna. The slot is not only used as the feeding structure for exciting characteristic modes but also introduces a slot mode. Combining the slot mode with the metasurface modes, the bandwidth of the antenna is broadened. The antenna element has a relative bandwidth of 43.7%. To obtain higher gain, a 2 × 2 antenna array is proposed. The antenna array is simulated, fabricated, and measured. The results show that the relative bandwidth of the proposed metasurface antenna array is 31.6% with the gain of 12.3–15.8 dBi over the operating bandwidth.

This research article proposes a dual-sense dual-port wideband circularly polarized (CP) multi-input multi-output (MIMO) antenna designed for Wi-Fi 6E applications. The main novelty lies in achieving CP for both ports using a truncated rectangular-shaped aperture. By incorporating design and spatial diversity and defective ground structure between the two radiators, the design improves isolation and enables the antenna to generate Left-Hand Circular Polarization (LHCP)depending on the selected feed port. The proposed MIMO rectangular dielectric resonator antenna demonstrates an impressive impedance-matching bandwidth (IBW)from 5.5 to 8.0 GHz (37.10%) as well as an axial ratio bandwidth (ARBW) covering from 6.0 to 6.55 GHz (12.20%). Additionally, the dual-port wideband CP MIMO antenna exhibits satisfactory diversity performance parameters. To validate the simulated results, a physical prototype is fabricated and subjected to experimental testing. The measured outcomes of the fabricated model align closely with the simulated results, confirming the accuracy of the design. With both MIMO and CP capabilities and improved isolation, this proposed model proves beneficial in reducing latency and minimizing the impact of multipath fading. Therefore, it stands as an excellent choice for future devices utilizing the Wi-Fi 6E band due to its broad IBW and overlappingAR.

A systematic design approach is presented for the design of broadband high-efficiency power amplifiers (PAs) by combining an improved ring-resonant filter matching network with a series of continuous modes. The improved ring-resonant matching network presented can effectively enhance out-of-band attenuation and sharp roll-off characteristics by adding a compensation structure with parallel stub. To verify the proposed design theory, a 10-W GaN HEMT device is designed and fabricated. The test results indicate that from the operating frequency band of 0.55−3.3 GHz with a relative bandwidth of 142.9%, a saturated output power of 38.5−42 dBm, drain efficiency of 58.2−70.3%, and a gain of 8.5–12 dB can be achieved under 3 dB gain compression, indicating the rationality of the design theory.

Large reflector antennas, such as the European Space Agency deep space antennas (DSAs), practically always require struts to support the sub-reflector. While inevitable, they deteriorate the antenna performance. To minimize this deterioration, it is pivotal to understand the role played by different features, including struts diameter and shape. This paper proposes a detailed numerical investigation on the impact of these features on antenna efficiency and side lobes, for a test case comprising both DSA3 and DSA4. It is demonstrated, for the first time in a comprehensive and quantitative way that includes different permutations for the strut design, that both features are significant to define the deterioration, thus providing a significant feedback for struts design.

Path loss prediction (PLP) is an important feature of wireless communications because it allows a receiver to anticipate the signal strength that will be received from a transmitter at a given distance. The PLP is done by using machine learning models that take into account numerous aspects such as the frequency of the signal, the surroundings, and the type of antenna. Various machine learning methods are used to anticipate path loss propagation but it is difficult to predict path loss in unknown propagation conditions. In existing models rely on incomplete or outdated data, which can affect the accuracy and reliability of predictions and they do not take into account the effects of environmental factors, such as terrain, foliage, and weather conditions, on path loss. Furthermore, existing models are not robust enough to handle the real-world variability and uncertainty, leading to significant errors in predictions. To tackle this issue, a novel ultrahigh frequency (UHF) PLP based on K-nearest neighbors (KNNs) is developed for predicting and optimizing the path loss for UHF. In this proposed model, a KNN-based PLP has been used to predict the path loss in the UHF. This technique is used for high-accuracy PLP through KNN forecast route loss by determining the K-nearest data points to a particular test point based on a distance metric. Moreover, the existing models were not able to optimize path loss due to complex and large-scale machine learning models. Therefore, the stochastic gradient descent technique has been used to minimize the objective function, which is often a measure of the difference between the model’s predictions and the actual output that will fine-tune the parameters of the KNN model, by measuring the similarity between data points. This model is implemented using Python to make it a lot more convenient.

Resonant Bessel-beam launchers (BBLs)are radiating devices constituted by a cylindrical metallic cavity with a partially reflecting sheet (PRS) on top. Millimeter-wave resonant BBLs typically exhibit transverse magnetic (TM) polarization due to the use of coaxial probes as feeders and homogenized metasurfaces as PRS. Launchers showing either a purely transverse electric (TE) or a hybrid (quasi-TE) polarization have recently been proposed for realizing wireless power transfer (WPT) links in the radiative near-field region at millimeter waves. The former are obtained by means of a radial slot array as a feeder and a homogenized metasurface as a PRS. The latter are obtained by using a loop antenna as a feeder and an annular strip grating in the homogenization limit as radiating aperture. In this work, based on an original semi-analytical model, such a metasurface is demonstrated to show a dichroic behavior. This interpretation explains the improvement in terms of polarization purity with respect to more nondichroic conventional homogenized metasurfaces. The behavior of the annular strip grating under a pure TM polarization is tested with a coaxial feeder, whereas its behavior under a pure TE polarization is tested by means of the radial slot array feeder. Results confirm the validity of the proposed analysis, which is finally exploited to evaluate the WPT performance.

A bandwidth expansion strategy for ultra-wideband power amplifiers (PAs) is presented in this letter by adopting a parallel impedance matching architecture. This design strategy can effectively reduce the impedance conversion ratio between the load and the target impedance of the PA, thereby providing a feasible solution for broadband impedance matching. Subsequently, a commercially available 10 W gallium nitride device and a two-stage Wilkinson power divider network are combined to achieve the verification of the proposed theory. The results of the measurement show that within the target frequency band of 0.9–3.9 GHz, 58.5–71.2% of the drain efficiency and 9.1–12 dB of gain can be achieved with a saturated output power of 39.1–42 dBm.

Normally, the reported gain of the microstrip patch antenna is within 8 dBi. Using properly located three shorting pins on three bisectors, the present work reports a method to convert the non-radiating TM11 mode of equilateral triangular patch antennas (ETPAs) to a deformed TM11 radiating mode. The boresight gain of ETPA operating in TM11 mode is enhanced from −10.75 to 12.1 dBi at 5.43 GHz. The boresight measured gain is further enhanced to 14.2 dBi at 5.52 GHz by using a triangular surface-mounted short horn (SMSH) of about ${{\lambda }}/5$ height. The aperture efficiency of the ETPA with the shorting pins is 84.2%. The aperture efficiency is further improved to 94.2% using the SMSH. The measured boresight cross-polarization and side-lobe level are −40 and −29 dB, respectively. The nature of the electricfield and surface current distribution is analyzed, using both the characteristic mode analysis method and high-frequency structure simulator, to understand the role of shorting pin and coaxial feed in converting the non-radiating TM11 mode to the radiating mode. A systematic design process also is presented for a fast design of shorting pin-loaded ETPA on the suitable substrate at a specified frequency.

This paper presents a method for measuring whole-body specific absorption rate (WBSAR) of millimeter-wave base stations (BSs) in a reverberation chamber (RC). The absorbed power in the phantom from the equipment under test (EUT) and hence WBSAR is determined as the difference between the total radiated power with and without the phantom. A chamber transfer function is determined and used to include only the absorption in the phantom due to direct illumination from the EUT, i.e., excluding absorption due to the RC multipath reflections. The measurement method was evaluated at 28 GHz using a horn antenna and a commercial massive multi-input–multi-output BS. The experimental results are in good agreement with simulations. The proposed method allows for measurements of WBSAR within 3 minutes, which is much shorter than traditional approaches. The method is suitable for compliance assessments of BS products with the International Commission on Non-Ionizing Radiation Protection 2020 electromagnetic field exposure guidelines, which extend the applicability of WBSAR as basic restrictions up to 300 GHz.

This paper explores the use of inkjet-printing technology for transparent transmitarrays, presenting a viable alternative to traditional copper microwire counterparts. The study focuses on achieving high-gain performance crucial for wireless communication systems, with a particular emphasis on the fifth-generation (5G) millimeter-wave communication. Transparent transmitarrays leverage transparent conducting films and conductive mesh structures, overcoming opacity limitations and seamlessly integrating with urban architecture. In this paper, the inkjet-printing process is detailed for fabricating transmitarray apertures, highlighting the flexibility and precision in depositing nanosilver particles onto a glass substrate. The design intricacies involve optimizing feeding characteristics, determining unit cell structures, and constructing transmitarrays of various sizes. To validate the proposed technique, three different apertures (15 × 15, 20 × 20, and 25 × 25 unit cells) are constructed. The antenna performances are evaluated in terms of reflection coefficients, radiation efficiency, realized gain, and patterns, demonstrating the effectiveness of inkjet-printed transmitarrays. Comparative analysis with copper microwire counterparts is also conducted, validating the inkjet-printing technology for similar gain performance with added advantages of flexibility, compatibility with transparent substrates, and cost-effective manufacturing.

In this article, a new microstrip dual-narrowband bandpass filter employing parallel-coupled transmission lines and open stubs is presented, investigated, and fabricated. The proposed dual-narrowband bandpass filter is analyzed and its exact scattering parameters are calculated, simulated, and measured. So, calculated scattering parameters offer a deep inside view of the performance of the proposed filter. To analyze the proposed filter, the even- and odd-mode excitation are utilized. The input impedance under even- and odd-mode excitation are achieved by transmission line theory and inserted in the scattering parameter equations. Finally, the accurate scattering parameters are derived and compared with simulation results. Simulation results prove the theoretical results. Then, an optimized proposed filter is fabricated and matched with simulation results. The center frequency bands are 4.5 and 6.8 GHz. The optimized filter occupies 0.12 $ \times $ 0.096$\lambda _g^2$, which is small. Its fractional bandwidth of the first and second passband are 1.5 and 2.5%, respectively. Furthermore, wide and strong rejection levels in the stopbands are offered. The structure of the proposed filter provides many freedoms to design. There is an agreement between experimental and simulation results.

In this study, a high-isolation multiple-input multiple-output (MIMO) microstrip patch antenna (MPA), which utilizes an orthogonal mode cancellation method is proposed. This method employs TM10 and TM01 modes, which are simultaneously excited in the rectangular passive MPA. Initially, a rectangular decoupling structure featuring polarization rotation characteristics is designed. Further studies show that by loading the polarization conversion parasitic structure (PCPS), the electric field of the spatial coupling wave can be transformed from the x-polarized TM10 mode to the y-polarized TM01 mode. Therefore, TM10 and TM01 modes from the excited antenna and decoupling structure are concurrently coupled to the passive antenna, forming an evident weak-field region on the passive antenna. Placing the feeding probe of the passive MPA within the weak-field region prevents signal reception at the port. Consequently, this results in an extremely low mutual coupling of −49 dB at a resonant frequency of 5.8 GHz. Finally, a prototype of the proposed antenna is fabricated and tested, and the measured results closely match the simulated results. Additionally, it is observed that PCPS slightly influences the performance of the MIMO antenna.

Development of large-scale quantum computing systems will require radio frequency (RF) and microwave technologies operating reliably at cryogenic temperatures down to tens of milli-Kelvin (mK). The quantum bits in the most promising quantum computing technologies such as the superconducting quantum computing are designed using principles of microwave engineering and operated using microwave signals. The control, readout, and coupling of qubits are implemented using a network of microwave components operating at various temperature stages. To ensure reliable operation of quantum computing systems, it is critical to ensure optimal performance of these microwave components and qubits at their respective operating temperatures, which can be as low as mK temperatures. It is, therefore, critical to understand the microwave characteristics of waveforms, components, circuits, networks, and systems at cryogenic temperatures. The UK’s National Physical Laboratory (NPL) is focussed on developing new microwave measurement capabilities through the UK’s National Quantum Technologies Programme to address various microwave test and measurement challenges in quantum computing. This includes the development of various measurement capabilities to characterize the microwave performance of quantum and microwave devices and substrate materials at cryogenic temperatures. This paper summarizes the roadmap of activities at NPL to address these microwave metrology challenges in quantum computing.

Worldwide adoption of 5G mobile devices has been one of the main driving engines behind semiconductor industry. Since the initial release in 2020, 5G-enabled devices have surpassed the market penetration of 3G/4G smartphones. 5G brings higher data capacity, low latency, and new applications. These are possible due to lower feature nodes such as FinFET 3 nm/5 nm but also due to improvements of the 5G radio frequency (RF)front-end circuitry. This paper presents 5G RF front-end architectures with novel circuits and measurement details which will be part of future 5G advanced and 6G mobile devices and are easier to be controlled using digital circuitry. The paper presents an envelope-controlled power amplifier (PA) principle, along with a novel simplified calibration architecture designed for 5G/5G+ operating under 6 GHz, as well as for frequency range 2 millimeter-wave PAs. An earlier version of this paper was presented at the 2023 53rd European Microwave Conference and was published in the Proceedings [Balteanu F, Thoomu K, Pingale A, Venimadhavan S, Sarkar S, Choi Y, Modi H, Drogi S, Lee J and Agarwal B (2023) Enabling RF circuit techniques for 5G and beyond In 53rd European Microwave Conference (EuMC), Berlin, Germany, 22–25].

This work presents a study where a sinusoidal corrugated antipodal Vivaldi antenna (SC-AVA) operating in the ultra-wideband (UWB) region is employed as a transducer for microwave imaging (MWI) of a cancerous breast. The functionality of the antenna within the UWB range is confirmed based on performance parameters like return loss, gain, radiation pattern, fidelity factor, and group delay. E-field distribution, H-field distribution, and near field directivity simulations in the presence of the breast phantom have also been carried out and reported. The practical application of the developed antenna for biomedical imaging is evaluated by measuring the specific absorption rate (SAR) readings at multiple frequencies within its operating range. The SAR readings are obtained from an electromagnetic simulator by modelling a realistic heterogeneous breast phantom with multiple embedded tumors, and placing them in close proximity to the transducer. The modelled SC-AVA is further utilized for imaging multiple tumors hidden inside the gland layer of the heterogeneous breast phantom developed in-house. The fabricated breast phantom is scanned using the in-house developed multistatic MWI setup. Based on the data obtained from the scanning setup the images are reconstructed using both the delay multiply and sum (DMAS) and iterative DMAS imaging algorithms. Furthermore, a comparison of the reconstructed images is done to check in which case the obtained images are closer to the fabricated breast phantom.

This paper presents a Ka-band series single-pole double-throw (SPDT) switch circuit realized in substrate-integrated coaxial line (SICL) environment for time division duplex operation. It is designed with a low-cost printed circuit board (PCB) technique. The size of the proposed circuit is $3.1\lambda_{g} \times 5.9\lambda_{g}$, where λg is the guided wavelength at the center frequency of 27.75 GHz. In this circuit, a SICL-based SPDT switching circuit is proposed with radio frequency (RF) isolation network where the shunt connection of butterfly stubs is in an asymmetric stripline environment. The proposed circuit exhibits less than 2 dB insertion loss at 27–27.9 GHz and less than 2.5 dB insertion loss at 27–28.5 GHz. The design offers good impedance matching in the Transmit (Tx) and Receive (Rx) channels from the common Tx/Rx input channel, along with more than 24 dB isolation between ON and OFF state output channels. The proposed circuit is suitable for millimeter-wave communication systems.

This paper presents a two-dimensional (2D) metasurface antenna array composed of mushroom cells coupled by thin slots in the top metallization. The antenna is fed through power dividers designed in substrate-integrated waveguide technology. The antenna structure is therefore designed in a fully up-to-date integrated version. The array shows beam steering in the azimuthal plane controlled by signal amplitudes fed into particular ports at the edges of the matrix. The main advantage of this antenna is no need to use phase shifters applied in standard 2D antenna arrays. Two antenna versions have been designed, fabricated, and experimentally tested. The beam can be steered within 360° (90°) in azimuth. The steering of the beam in elevation from backward to forward directions within 40° is done by changing frequency from 21 up to 23.8 GHz. This interval is reduced to 30° by exciting the antenna simultaneously at two adjacent ports at the same amplitude.

This paper introduces a tri-band stacked elliptical patch antenna featuring a right-handed circular polarized, designed to operate at the L2, L5, and L1 Global Navigation Satellite System bands. Initially, an elliptic patch is constructed and fed by a probe feed to generate TM110 and TM210 modes at resonance frequencies calculated using Mathieu functions. The probe position is precisely adjusted to excite the quasi-orthogonal mode of TM110 to generate circularly polarized (CP) waves at the L2 and L5 bands. Subsequently, an eye-shaped aperture is engraved into the elliptical patch to enhance the axial ratio (AR) beamwidth in the L2 and L5 bands and stimulate the orthogonal mode of TM210 to produce CP waves at the L1 band. Lastly, a stacked partially elliptical parasitic element is placed beneath the upper slotted elliptical patch to enhance the orthogonality of TM210 surface current versions and thus improve the AR beamwidth at the L1 band. The proposed antenna shows low reflection coefficient values at 1.12–1.33 (L2/L5), and 1.5–1.66 GHz (L1). The AR beamwidths are 133/213∘, 167/163∘, and 36/103∘ at two orthogonal cutplanes at L5, L2, and L1 bands, respectively. The antenna also has decent gains of 6–6.9 dBic across the three bands.