Hostname: page-component-cd9895bd7-7cvxr Total loading time: 0 Render date: 2024-12-26T07:41:11.755Z Has data issue: false hasContentIssue false
  • English
  • Français

Heat transfer from a hot film in reversing shear flow

Published online by Cambridge University Press:  11 April 2006

T. J. Pedley
T. J. Pedley
Affiliation:
Department of Applied Mathematics and Theoretical Physics, University of Cambridge
Get access Rights & Permissions [Opens in a new window]

Abstract

The two-dimensional thermal boundary layer over a finite hot film embedded in a plane insulating wall, with a shear flow over it which reverses its direction, is analysed approximately using methods similar to those previously developed for viscous boundary layers (Pedley 1976). The heat transfer from the film is calculated both for uniformly decelerated and for oscillatory wall shear, and application is made to predict the response of hot-film anemometers actually used to measure oscillatory velocities in water and blood. The results predict that the velocity amplitude measured on the assumption of a quasi-steady response will depart from the actual amplitude at values of the frequency parameter St greater than about 0·3 (St = ΩX0/U0, where Ω = frequency, U0 = mean velocity, X0 = distance of hot film from the leading edge of the probe). This is in good agreement with experiment. So too is the shape of the predicted anemometer output as a function of time throughout a complete cycle, for cases when the response is not quasi-steady. However, there is a significant phase lead between the predicted and the experimental outputs. Various possible reasons for this are discussed; no firm conclusions are reached, but the most probable cause lies in the three-dimensionality of the velocity and temperature fields, since the experimental hot films are only about 2·5 times as broad as they are long, and are mounted on a cylinder not a flat plate.

Type
Research Article
Information
Journal of Fluid Mechanics , Volume 78 , Issue 3 , 7 December 1976 , pp. 513 - 534
Copyright
© 1976 Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Bellhouse, B. J. & Schultz, D. L. 1967 The determination of fluctuating velocity in air with heated thin film gauges. J. Fluid Mech. 29, 289.Google Scholar
Clark, C. 1974 Thin film gauges for fluctuating velocity measurements in blood. J. Phys. E, Sci. Inatr. 7, 548.Google Scholar
Lévéque, M. A. 1928 Transmission de chaleur par convection. Ann. des Mines, 13, 283.Google Scholar
Liepmann, H. W. & Skinner, G. T. 1954 Shearing-stress measurements by use of a heated element. N.A.C.A. Tech. Note, no. 3268.Google Scholar
Pedley, T. J. 1972a On the forced heat transfer from a hot film embedded in the wall in two-dimensional unsteady flow. J. Fluid Mech. 55, 329.Google Scholar
Pedley, T. J. 1972b Two-dimensional boundary layers in a free stream which oscillates without reversing. J. Fluid Mech. 55, 359.Google Scholar
Pedley, T. J. 1975 A thermal boundary layer in a reversing flow. J. Fluid Mech. 67, 209.Google Scholar
Pedley, T. J. 1976 Viscous boundary layers in reversing flow. J. Fluid Mech. 74, 59.Google Scholar
Rosenhead, L. (ed.) 1963 Laminar Boundary Layers. Oxford: Clarendon Press.
Seed, W. A. & Wood, N. B. 1970 Use of a hot film velocity probe for cardiovascular studies. J. Phys. E, Sci. Instr. 3, 377.Google Scholar
Springer, S. G. 1974 The solution of heat-transfer problems by the Wiener-Hopf technique. II. Trailing edge of a hot film. Proc. Roy. Soc. A 337, 395.Google Scholar