Hostname: page-component-78c5997874-v9fdk Total loading time: 0 Render date: 2024-11-14T23:50:35.385Z Has data issue: false hasContentIssue false
  • English
  • Français

The dynamic indentation behavior of steel at large depths of penetration

Published online by Cambridge University Press:  31 January 2011

G. Sundararajan  and
S.N. Dikshit
G. Sundararajan*
Affiliation:
International Advanced Research Centre for Powder Metallurgy and New Materials, Hyderabad-500005, India
S.N. Dikshit
Affiliation:
International Advanced Research Centre for Powder Metallurgy and New Materials, Hyderabad-500005, India
*
a) Address all correspondence to this author. e-mail: gsundar@arci.res.inThis author was an editor of this focus issue during the review and decision stage. For the JMR policy on review and publication of manuscripts authored by editors, please refer to http://www.mrs.org/jmr_policy
Get access

Abstract

The objective of the present study is to investigate the dynamic indentation behavior of steel plate material when impacted by ogive-shaped projectiles and in particular under indentation conditions involving large depths of penetration (i.e., depth of penetration greater than projectile radius). Toward the above purpose, dynamic indentation of steel plates of thickness 20, 40, and 80 mm have been carried out using projectiles of diameter 6.2 and 20 mm, and over a range of impact velocities so as to attain depths of penetration in the range 1.4 to 3.6 times the projectile radius. The results indicate that the dynamic hardness, the plastic zone size, specific energy consumed in plastic deformation within the plastic zone, and the average plastic strain within the plastic zone increases continuously with increasing values of depth of penetration normalized by projectile radius. Certain subtle differences regarding the nature of plastic deformation between indentation at large and shallow depths of penetration are presented. However, on a macroscopic scale, the indentation mechanisms and processes are broadly similar and show continuity in terms of behavior across the whole penetration depth range.

Keywords

HardnessMetalStress/strain relationship
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 3 , March 2009 , pp. 691 - 703
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Tabor, D.: The Hardness of Metals (Oxford University Press, UK, 1951).Google Scholar
2.Mok, C.H. and Duffy, J.: The dynamic stress-strain relation of metals as determined from impact tests with a hard ball. Int. J. Mech. Sci. 7, 355 (1965).CrossRefGoogle Scholar
3.Sundararajan, G. and Shewmon, P.G.: The use of dynamic impact experiments in the determination of the strain rate sensitivity of metals and alloys. Acta Metall. 31, 101 (1983).CrossRefGoogle Scholar
4.Tirupataiah, Y. and Sundararajan, G.: A dynamic indentation technique for the characterization of high strain rate flow behavior of ductile materials. J. Mech. Phys. Solids 39, 243 (1991).CrossRefGoogle Scholar
5.Subhash, G., Koeppel, B.J., and Chandra, A.: Dynamic indentation hardness and rate sensitivity in metals. J. Eng. Mater. Technol. 121, 257 (1999).CrossRefGoogle Scholar
6.Koeppel, B.J. and Subhash, G.: Characteristics of residual plastic zone under static and dynamic Vickers indentation. Wear 224, 56 (1999).CrossRefGoogle Scholar
7.Sundararajan, G. and Tirupataiah, Y.: The localization of plastic flow during dynamic indentation. I: Experimental results. Acta Mater. 54, 565 (2006).CrossRefGoogle Scholar
8.Sundararajan, G. and Tirupataiah, Y.: The localization of plastic flow during dynamic indentation. II: Analysis of results. Acta Mater. 54, 577 (2006).CrossRefGoogle Scholar
9.Clough, R.B., Webb, S.C., and Armstrong, R.W.: Dynamic hardness measurements using a dropped ball-With application to 1018 steel. Mater. Sci. Eng., A 360, 396 (2003).CrossRefGoogle Scholar
10.Dikshit, S.N., Kutumba Rao, V.V., and Sundararajan, G.: The influence of plate hardness on the ballistic penetration of thick steel plates. Int. J. Impact Eng. 16, 293 (1995).CrossRefGoogle Scholar
11.Dikshit, S.N.: A comprehensive analysis of the ballistic penetration of high kinetic energy projectiles into steels: Experiment and modelling. Ph.D. Thesis, Defence Metallurgical Research Laboratory, Hyderabad, India, 1996.Google Scholar
12.Dikshit, S.N. and Sundararajan, G.: The penetration of thick steel plates by ogive shaped projectiles: Experiment and analysis. Int. J. Impact Eng. 12, 373 (1992).CrossRefGoogle Scholar