Hostname: page-component-78c5997874-94fs2 Total loading time: 0 Render date: 2024-11-14T23:26:59.503Z Has data issue: false hasContentIssue false
  • English
  • Français

Fracture modes in curved brittle layers subject to concentrated cyclic loading in liquid environments

Published online by Cambridge University Press:  31 January 2011

Jae-Won Kim ,
Van P. Thompson ,
E. Dianne Rekow ,
Yeon-Gil Jung  and
Yu Zhang
Jae-Won Kim
Affiliation:
Department of Biomaterials and Biomimetics, New York University College of Dentistry, New York, New York 10010
Van P. Thompson
Affiliation:
Department of Biomaterials and Biomimetics, New York University College of Dentistry, New York, New York 10010
E. Dianne Rekow
Affiliation:
Basic Science Department, New York University College of Dentistry, New York, New York 10010
Yeon-Gil Jung
Affiliation:
School of Nano and Advanced Materials Engineering, Changwon National University, Changwon, Korea
Yu Zhang*
Affiliation:
Department of Biomaterials and Biomimetics, New York University College of Dentistry, New York, New York 10010
*
a) Address all correspondence to this author. e-mail: yz21@nyu.edu
Get access

Abstract

Damage response of brittle curved structures subject to cyclic Hertzian indentation was investigated. Specimens were fabricated by bisecting cylindrical quartz glass hollow tubes. The resulting hemicylindrical glass shells were bonded internally and at the edges to polymeric supporting structures and loaded axially in water on the outer circumference with a spherical tungsten carbide indenter. Critical loads and number of cycles to initiate and propagate near-contact cone cracks and far-field flexure radial cracks to failure were recorded. Flat quartz glass plates on polymer substrates were tested as a control group. Our findings showed that cone cracks form at lower loads, and can propagate through the quartz layer to the quartz/polymer interface at lower number of cycles, in the curved specimens relative to their flat counterparts. Flexural radial cracks require a higher load to initiate in the curved specimens relative to flat structures. These radial cracks can propagate rapidly to the margins, the flat edges of the bisecting plane, under cyclic loading at relatively low loads, owing to mechanical fatigue and a greater spatial range of tensile stresses in curved structures.

Keywords

FatigueFractureLayered
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 3 , March 2009 , pp. 1075 - 1081
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Lawn, B.R., Bhowmick, S., Bush, M.B., Qasim, T., Rekow, E.D., and Zhang, Y.: Failure modes in ceramic-based layer structures: A basis for materials design of dental crowns. J. Arn. Cerarti. Soc. 90, 1671 (2007).Google Scholar
2.Lawn, B.R., Deng, Y., Miranda, P., Pajares, A., Chai, H., and Kim, D.K.: Overview: Damage in brittle layer structures from concentrated loads. J. Mater. Res. 17, 3019 (2002).CrossRefGoogle Scholar
3.Zhang, Y., Kim, J.W., Bhowmick, S., Thompson, V.P., and Rekow, E.D.: Competition of fracture mechanisms in monolithic dental ceramics: Flat model systems. J. Biomed. Mater. Res. 88B, 402 (2008).CrossRefGoogle Scholar
4.Kim, J.W., Bhowmick, S., Chai, H., and Lawn, B.R.: Role of substrate material in failure of crown-like layer structures. J. Biomed. Mater. Res. 81B, 305 (2007).CrossRefGoogle Scholar
5.Qasim, T., Bush, M.B., Hu, X., and Lawn, B.R.: Contact damage in brittle coating layers: Influence of surface curvature. J. Biomed. Mater. Res. 73B, 179 (2005).CrossRefGoogle Scholar
6.Rudas, M., Qasim, T., Bush, M.B., and Lawn, B.R.: Failure of curved brittle layer systems from radial cracking in concentrated surface loading. J. Mater. Res. 20, 2812 (2005).CrossRefGoogle Scholar
7.Ford, C., Qasim, T., Bush, M.B., Hu, X., Shah, M.M., Saxena, V.P., and Lawn, B.R.: Margin failures in crown-like brittle structures: Off-axis loading. J. Biomed. Mater. Res. 85B, 23 (2008).CrossRefGoogle Scholar
8.Qasim, T., Ford, C., Bush, M.B., Hu, X., and Lawn, B.R.: Effect of off-axis concentrated loading on failure of curved brittle layer structures. J. Biomed. Mater. Res. 76B, 334 (2006).CrossRefGoogle Scholar
9.Qasim, T., Ford, C., Bush, M.B., Hu, X., Malament, K.A., and Lawn, B.R.: Margin failures in brittle dome structures: Relevance to failure of dental crowns. J. Biomed. Mater. Res. 80B, 78 (2007).CrossRefGoogle Scholar
10.Bhowmick, S., Zhang, Y., and Lawn, B.R.: Competing fracture modes in brittle materials subject to concentrated cyclic loading in liquid environments: Bilayer structures. J. Mater. Res. 20, 2792 (2005).CrossRefGoogle Scholar
11.Zhang, Y. and Lawn, B.R.: Competing damage modes in all-ceramic crowns: Fatigue and lifetime. Bioceram. 17, 697 (2005).Google Scholar
12.Zhang, Y., Song, J.K., and Lawn, B.R.: Deep-penetrating conical cracks in brittle layers from hydraulic cyclic contact. J. Biomed. Mater. Res. 73B, 186 (2005).CrossRefGoogle Scholar
13.Zhang, Y., Bhowmick, S., and Lawn, B.R.: Competing fracture modes in brittle materials subject to concentrated cyclic loading in liquid environments: Monoliths. J. Mater. Res. 20, 2021 (2005).CrossRefGoogle Scholar
14.Kelly, J.R.: Clinically relevant approach to failure testing of all-ceramic restorations. J. Prosthet. Dent. 81, 652 (1999).CrossRefGoogle ScholarPubMed
15.Kim, B., Zhang, Y., Pines, M., and Thompson, V.P.: Fracture of porcelain-veneered structures in fatigue. J. Dent. Res. 86, 142 (2007).CrossRefGoogle ScholarPubMed
16.Rhee, Y.-W., Kim, H.-W., Deng, Y., and Lawn, B.R.: Brittle fracture versus quasiplasticity in ceramics: A simple predictive index. J. Am. Ceram. Soc. 84, 561 (2001).CrossRefGoogle Scholar
17.Bhowmick, S., Melendez-Martinez, J.J., Hermann, I., Zhang, Y., and Lawn, B.R.: Role of indenter material and size in veneer failure of brittle layer structures. J. Biomed. Mater. Res. 82B, 253 (2007).CrossRefGoogle Scholar