Hostname: page-component-cd9895bd7-q99xh Total loading time: 0 Render date: 2024-12-27T11:42:43.531Z Has data issue: false hasContentIssue false
  • English
  • Français

Densification and deformation studies on powder metallurgy Al–TiO2–Gr composite during cold upsetting

Published online by Cambridge University Press:  10 July 2014

Manickam Ravichandran ,
Abdullah Naveen Sait  and
Veeramani Anandakrishnan
Manickam Ravichandran
Affiliation:
Department of Mechanical Engineering, Chendhuran College of Engineering and Technology, Pudukkottai 622 507, Tamilnadu, India
Abdullah Naveen Sait*
Affiliation:
Department of Mechanical Engineering, Chendhuran College of Engineering and Technology, Pudukkottai 622 507, Tamilnadu, India
Veeramani Anandakrishnan
Affiliation:
Department of Production Engineering, National Institute of Technology, Tiruchirappalli 620 015, Tamilnadu, India
*
a)Address all correspondence to this author. e-mail: naveensait@yahoo.co.in
Get access

Abstract

Aluminum metal matrix hybrid composites were synthesized through powder metallurgy route from ball milled powders to yield the compositions: Al + 0% TiO2, Al + 2.5% TiO2, Al + 2.5% TiO2 + 2% Gr, and Al + 2.5% TiO2 + 4% Gr. The densification and deformation properties of sintered Al–TiO2–Gr composites during cold upsetting were investigated experimentally. The powder preforms are compacted using suitable punch and die in 40 kN hydraulic press and the initial percentage theoretical density was maintained as 85%. Sintering was done in an electric muffle furnace at the temperature of 590 °C for a period of 3 h. The sintered preforms were subjected to incremental compressive loading of 10 kN until cracks were found at the free surface. The true axial stress (σz), true hoop stress (σθ), true hydrostatic stress (σm), and true effective stress (σeff) were calculated for all the preforms and all these stresses are correlated with the true axial strain (εz). The densification behaviors of the composites were studied against true axial strain (εz) and lateral strain. Better densification and deformation property were obtained for pure aluminum preforms compared with other composite preforms. Addition of TiO2 to the pure Al and Gr reinforcements increases the strength coefficient of the Al–TiO2 composite.

Keywords

metal matrix compositesTiO2cold upsettingpowder metallurgyaluminum
Type
Articles
Information
Journal of Materials Research , Volume 29 , Issue 13 , 14 July 2014 , pp. 1480 - 1487
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Rahimian, M., Parvin, N., and Ehsani, N.: The effect of production parameters on microstructure and wear resistance of powder metallurgy Al -Al2O3 composite. Mater. Des. 32, 1031–1038 (2011).Google Scholar
Ravindran, P., Manisekar, K., Narayanasamy, P., Selvakumar, N., and Narayanasamy, R.: Application of factorial techniques to study the wear of Al hybrid composites with graphite addition. Mater. Des. 39, 42–54 (2012).CrossRefGoogle Scholar
Ted Guo, M.L. and Tsao, C.Y.A.: Tribological behavior of self-lubricating aluminium/SiC/graphite hybrid composites synthesized by the semi-solid powder-densification method. Compos. Sci. Technol. 60, 65–74 (2000).Google Scholar
Mahdavi, S. and Akhlaghi, F.: Effect of the graphite content on the tribological behavior of Al/Gr and Al/30SiC/Gr composites processed by in situ powder metallurgy (IPM) Method. Tribol. Lett. 44, 1–12 (2011).Google Scholar
Sivasankaran, S., Sivaprasad, K., Narayanasamy, R., and Iyer, V.K.: An investigation on flowability and compressibility of AA 6061100–x-x wt.% TiO2 micro and nanocomposite powder prepared by blending and mechanical alloying. Powder Technol. 201, 70–82 (2010).CrossRefGoogle Scholar
Vaezi, M.R.: Two-step solochemical synthesis of ZnO/TiO2 nano-composite materials. J. Mater. Process. Technol. 205, 332–337 (2008).Google Scholar
Mazahery, A. and Shabani, M.O.: Study on microstructure and abrasive wear behavior of sintered Al matrix composites. Ceram. Int. 38, 4263–4269 (2012).Google Scholar
Narayanasamy, R., Ramesh, T., and Pandey, K.S.: Some aspects on cold forging of aluminium-alumina powder metallurgy composite under triaxial stress state condition. Mater. Des. 29, 1212–1227 (2008).Google Scholar
Narayanasamy, R., Ramesh, T., Pandey, K.S., and Pandey, S.K.: Effect of particle size on new constitutive relationship of aluminium -iron powder metallurgy composite during cold upsetting. Mater. Des. 29, 1011–1026 (2008).Google Scholar
Narayanasamy, R., Anandakrishnan, V., and Pandey, K.S.: Effect of geometric work-hardening and matrix work-hardening on workability and densification of aluminium -3.5% alumina composite during cold upsetting. Mater. Des. 29, 1582–1599 (2008).Google Scholar
German, R.M.: Powder Metallurgy Science, 2nd ed. (Metal Powder Industries Federation, New Jersey, 1984).Google Scholar
Baskaran, K. and Narayanasamy, R.: An experimental investigation on work hardening behaviour of elliptical shaped billets of aluminium during cold upsetting. Mater. Des. 29, 1240–1265 (2008).Google Scholar
Dieter, G.E.: Mechanical Metallurgy, SI Metric ed. (McGraw-Hill Book Company, London, 1988).Google Scholar