Hostname: page-component-cd9895bd7-lnqnp Total loading time: 0 Render date: 2024-12-28T01:04:36.291Z Has data issue: false hasContentIssue false
  • English
  • Français

Dynamic recrystallization and microstructure evolution of a powder metallurgy nickel-based superalloy under hot working

Published online by Cambridge University Press:  09 June 2016

Yanhui Liu ,
Yongquan Ning ,
Zekun Yao ,
Yuzhi Li ,
Jingli Zhang  and
Mingwang Fu
Yanhui Liu*
Affiliation:
School of Materials Science & Engineering, Northwestern Polytechnical University, Xi'an 710072, People's Republic of China
Yongquan Ning
Affiliation:
School of Materials Science & Engineering, Northwestern Polytechnical University, Xi'an 710072, People's Republic of China
Zekun Yao
Affiliation:
School of Materials Science & Engineering, Northwestern Polytechnical University, Xi'an 710072, People's Republic of China
Yuzhi Li
Affiliation:
School of Materials Science & Engineering, Northwestern Polytechnical University, Xi'an 710072, People's Republic of China
Jingli Zhang
Affiliation:
School of Materials Science & Engineering, Northwestern Polytechnical University, Xi'an 710072, People's Republic of China
Mingwang Fu
Affiliation:
Department of Mechanical Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong
*
a) Address all correspondence to this author. e-mail: liuyanhui36@mail.nwpu.edu.cn
Get access

Abstract

The deformation behaviors (flow behavior, power dissipation, dynamic recrystallization, and microstructure evolution) of a typical powder metallurgy nickel-based superalloy were investigated in compression tests at temperatures range of 1020–1140 °C and strain rates range of 0.001–1.0 s−1 with the true strains of 0.3, 0.5, and 0.7, respectively. The efficiency of power dissipation can be shown by the power dissipation maps at different true strains. The results showed that true strain had a great effect on the power dissipation. Besides, the deformed microstructures were investigated. The processes of microstructure evolution at different deformation temperatures and strain rates are different. The continuous dynamic recrystallization takes place at the deformation condition of 1080 °C/0.1 s−1. The fine and uniform dynamic recrystallized grains gradually replace the pre-existing grains with the increase of true strain. The discontinuous dynamic recrystallization takes place at the deformation condition of 1110 °C/0.001 s−1. The fine dynamic recrystallized grains grow up and a part of new fine grains appear in the dynamic recrystallized grains because of the periodic dynamic recrystallization.

Keywords

powder metallurgy superalloydeformation behaviorpower dissipationdynamic recrystallizationmicrostructure evolution
Type
Articles
Information
Journal of Materials Research , Volume 31 , Issue 14 , 28 July 2016 , pp. 2164 - 2172
Check for updates
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Jürgen Eckert

References

REFERENCES

Jiang, F.L., Zhang, H., Li, L.X., and Chen, J.H.: The kinetics of dynamic and static softening during multistage hot deformation of 7150 aluminum alloy. Mater. Sci. Eng., A 552, 269–275 (2012).Google Scholar
Chen, X.M., Lin, Y.C., Chen, M.S., Li, H.B., Wen, D.X., Zhang, J.L., and He, M.: Microstructural evolution of a nickel-based superalloy during hot deformation. Mater. Des. 77, 41–49 (2015).Google Scholar
Lin, Y.C., Li, L.T., Fu, Y.X., and Jiang, Y.Q.: Hot compressive deformation behavior of 7075 Al alloy under elevated temperature. J. Mater. Sci. 47(3), 1306–1318 (2012).Google Scholar
Tian, L., Ao, Q., and Li, S.L.: Effect of austenitic state on microstructure and mechanical properties of martensite/bainite steel. J. Mater. Res. 29(7), 887–895 (2014).Google Scholar
Li, Z.L., Xu, Q.Y., and Liu, B.C.: Microstructure simulation on recrystallization of an as-cast nickel based single crystal superalloy. Comput. Mater. Sci. 107, 122–133 (2015).Google Scholar
Liu, Y.Z., Hu, X.B., Zheng, S.J., Zhu, Y.L., Wei, H., and Ma, X.L.: Microstructural evolution of the interface between NiCrAlY coating and superalloy during isothermal oxidation. Mater. Des. 80, 63–69 (2015).Google Scholar
Sun, W., Qin, X.Z., Guo, J.T., Lou, L.H., and Zhou, L.Z.: Thermal stability of primary MC carbide and its influence on the performance of cast Ni-base superalloys. Mater. Des. 69, 81–88 (2015).Google Scholar
Bai, Q., Lin, J., Jiang, J., Dean, T.A., Zou, J., and Tian, G.: A study of direct forging process for powder superalloys. Mater. Sci. Eng., A 621, 68–75 (2015).Google Scholar
Chang, L.T., Sun, W.R., Cui, Y.Y., Zhang, F.Q., and Yang, R.: Effect of heat treatment on microstructure and mechanical properties of the hot-isostatic-pressed Inconel 718 powder compact. J. Alloys Compd. 590, 227–232 (2014).Google Scholar
Wang, M.H., Li, Y.F., Wang, W.H., Zhou, J., and Chiba, A.: Quantitative analysis of work hardening and dynamic softening behavior of low carbon alloy steel based on the flow stress. Mater. Des. 45, 384–392 (2013).Google Scholar
Li, L.X., Ye, B., Liu, S., Hu, S.D., and Li, B.: Inverse analysis of the stress–strain curve to determine the materials models of work hardening and dynamic recovery. Mater. Sci. Eng., A 636, 243–248 (2015).Google Scholar
Wu, K., Liu, G.Q., Hu, B.F., Li, F., Zhang, Y.W., Tao, Y., and Liu, J.T.: Hot compressive deformation behavior of a new hot isostatically pressed Ni–Cr–Co based powder metallurgy superalloy. Mater. Des. 32, 1872–1879 (2011).Google Scholar
Li, D.F., Guo, Q.M., Guo, S.L., Peng, H.J., and Wu, Z.G.: The microstructure evolution and nucleation mechanisms of dynamic recrystallization in hot-deformed Inconel 625 superalloy. Mater. Des. 32, 696–705 (2011).Google Scholar
Rettberg, L.H. and Pollock, T.M.: Localized recrystallization during creep in nickel-based superalloys GTD444 and René N5. Acta Mater. 73, 287–297 (2014).Google Scholar
Cai, Z.W., Chen, F.X., and Guo, J.Q.: Constitutive model for elevated temperature flow stress of AZ41M magnesium alloy considering the compensation of strain. J. Alloys Compd. 648, 215–222 (2015).Google Scholar
Liu, Y.H., Ning, Y.Q., Yao, Z.K., and Fu, M.W.: Hot deformation behavior of the 1.15C–4.00Cr–3.00V–6.00W–5.00Mo powder metallurgy high speed steel. Mater. Des. 54, 854–863 (2014).Google Scholar
Jiang, H., Dong, J.X., Zhang, M.C., Zheng, L., and Yao, Z.H.: Hot deformation characteristics of alloy 617B nickel-based superalloy: A study using processing map. J. Alloys Compd. 647, 338–350 (2015).Google Scholar
Wang, Y., Pan, Q.L., Song, Y.F., Li, C., and Li, Z.F.: Hot deformation and processing maps of X-750 nickel-based superalloy. Mater. Des. 51, 154–160 (2013).Google Scholar
Liu, Y.H., Ning, Y.Q., Nan, Y., Liang, H.Q., Li, Y.Z., and Zhao, Z.L.: Characterization of hot deformation behavior and processing map of FGH4096-GH4133B dual alloys. J. Alloys Compd. 633, 505–515 (2015).Google Scholar
Shang, X., Zhou, J., Wang, X., and Luo, Y.: Optimizing and identifying the process parameters of AZ31 magnesium alloy in hot compression on the base of processing maps. J. Alloys Compd. 629, 155–161 (2015).Google Scholar
Ning, Y.Q., Zhou, C., Liang, H.Q., and Fu, M.W.: Abnormal flow behavior and necklace microstructure of powder metallurgy superalloys with previous particle boundaries (PPBs). Mater. Sci. Eng., A 652, 84–91 (2016).Google Scholar
Zhang, H.Y., Zhang, S.H., Cheng, M., and Li, Z.X.: Deformation characteristics of δ phase in the delta-processed Inconel 718 alloy. Mater. Charact. 61, 49–53 (2010).Google Scholar