Hostname: page-component-cd9895bd7-q99xh Total loading time: 0 Render date: 2024-12-28T00:11:47.308Z Has data issue: false hasContentIssue false
  • English
  • Français

Hot deformation behavior and microstructural evolution of Nb–V–Ti microalloyed ultra-high strength steel

Published online by Cambridge University Press:  12 October 2017

Ji Dong ,
Chong Li ,
Chenxi Liu ,
Yuan Huang ,
Liming Yu ,
Huijun Li  and
Yongchang Liu
Ji Dong
Affiliation:
State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300354, People’s Republic of China
Chong Li*
Affiliation:
State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300354, People’s Republic of China
Chenxi Liu
Affiliation:
State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300354, People’s Republic of China
Yuan Huang
Affiliation:
State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300354, People’s Republic of China
Liming Yu
Affiliation:
State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300354, People’s Republic of China
Huijun Li
Affiliation:
State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300354, People’s Republic of China
Yongchang Liu*
Affiliation:
State Key Lab of Hydraulic Engineering Simulation and Safety, School of Materials Science & Engineering, Tianjin University, Tianjin 300354, People’s Republic of China; and Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai Jiao Tong University, Shanghai 200240, People’s Republic of China
*
a) Address all correspondence to these authors. e-mail: lichongme@tju.edu.cn
b) e-mail: licmtju@163.com
Get access

Abstract

The hot deformation behavior of Nb–V–Ti microalloyed ultra-high strength steel was investigated by isothermal compression at 900–1200 °C with strain rates from 0.01 to 10 s−1. The microstructure evolution and precipitation behavior were studied using an optical microscope and a transmission electron microscope Results indicate that the peak stress of experimental steel increases with increasing the strain rate and decreasing the deformation temperature. The constitutive equation of hot deformation was developed with the activation energy Q being about 407.29 kJ/mol. The processing maps were also obtained to identify the instable regions of the flow behavior and to evaluate the efficiency of hot deformation. The size of dynamically recrystallized grains increases gradually with a decrease in the strain rate. Three types of carbides were identified, namely M3C, rich-Ti MC, and rich-Nb MC. With the increase of the deformation rate, the amounts of carbides increase, and the average sizes of the carbides decrease gradually.

Keywords

Nb–V–Ti microalloyed ultra-high strength steelconstitutive equationprocessing mapmicrostructureprecipitates
Type
Article
Information
Journal of Materials Research , Volume 32 , Issue 19 , 16 October 2017 , pp. 3777 - 3787
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Jürgen Eckert

References

REFERENCES

Zhou, Y.L., Jia, T., Zhang, X.J., Liu, Z.Y., and Misra, R.D.K.: Investigation on tempering of granular bainite in an offshore platform steel. Mater. Sci. Eng., A 626, 352 (2015).CrossRefGoogle Scholar
Cheng, X.Y., Zhang, H.X., Li, H., and Shen, H.P.: Effect of tempering temperature on the microstructure and mechanical properties in mooring chain steel. Mater. Sci. Eng., A 636, 164 (2015).Google Scholar
Pouraliakbar, H., Khalaj, M., Nazerfakhari, M., and Khalaj, G.: Artificial neural networks for hardness prediction of HAZ with chemical composition and tensile test of X70 pipeline steels. J. Iron Steel Res. Int. 22, 446 (2015).Google Scholar
Yang, Y., Peng, X.D., Ren, F.J., Wen, H.M., Su, J.F., and Xie, W.D.: Constitutive modeling and hot deformation behavior of duplex structured Mg–Li–Al–Sr alloy. J. Mater. Sci. Technol. 32, 1289 (2016).Google Scholar
Shahrani, A.A., Yazdipour, N., Dehghan-Manshadi, A., Gazder, A.A., Cayron, C., and Pereloma, E.V.: The effect of processing parameters on the dynamic recrystallisation behaviour of API-X70 pipeline steel. Mater. Sci. Eng., A 570, 70 (2013).Google Scholar
Qian, L.Y., Fang, G., Zeng, P., and Wang, L.X.: Correction of flow stress and determination of constitutive constants for hot working of API X100 pipeline steel. Int. J. Pressure Vessels Piping 132–133, 43 (2015).Google Scholar
Quan, G.Z., Zhao, L., Chen, T., Wang, Y., Mao, Y.P., Lv, W.Q., and Zhou, J.: Identification for the optimal working parameters of as-extruded 42CrMo high-strength steel from a large range of strain, strain rate and temperature. Mater. Sci. Eng., A 538, 364 (2012).CrossRefGoogle Scholar
Gomez, M., Valles, P., and Medina, S.F.: Evolution of microstructure and precipitation state during thermomechanical processing of a X80 microalloyed steel. Mater. Sci. Eng., A 528, 4761 (2011).Google Scholar
Cao, Y.B., Xiao, F.R., Qiao, G.Y., Zhang, X.B., and Liao, B.: Quantitative research on effects of Nb on hot deformation behaviors of high-Nb microalloyed steels. Mater. Sci. Eng., A 530, 277 (2011).Google Scholar
Dong, J., Zhou, X.S., Liu, Y.C., Li, C., Liu, C.X., and Guo, Q.Y.: Carbide precipitation in Nb–V–Ti microalloyed ultra-high strength steel during tempering. Mater. Sci. Eng., A 683, 215 (2017).CrossRefGoogle Scholar
Dong, J., Zhou, X.S., Liu, Y.C., Li, C., Liu, C.X., and Li, H.J.: Effects of quenching-partitioning-tempering treatment on microstructure and mechanical performance of Nb–V–Ti microalloyed ultra-high strength steel. Mater. Sci. Eng., A 690, 283 (2017).Google Scholar
Liu, H.W., Rong, R., Gao, F., Li, Z.X., Liu, Y.G., and Wang, Q.F.: Hot deformation behavior and microstructural evolution characteristics of Ti–44Al–5V–1Cr alloy containing (γ + α2 + B2) phases. Metals 6(12), 3 (2016).Google Scholar
Zhong, H.Z., Li, Z., Song, M., Liang, X.P., and Guo, F.F.: Hot deformation behavior and microstructural evolution of Ag-containing 2519 aluminum alloy. Mater. Des. 31, 2171 (2010).Google Scholar
Zhou, Y.H., Liu, Y.C., Zhou, X.S., Liu, C.X., Yu, L.M., and Li, C.: Processing maps and microstructural evolution of the type 347H austenitic heat-resistant stainless steel. J. Mater. Res. 168, 2091 (2015).Google Scholar
Liu, Y.C., Guo, Q.Y., Li, C., Mei, Y.P., Zhou, X.S., Huang, Y., and Li, H.J.: Recent progress on evolution of precipitates in Inconel 718 superalloy. Acta Metall. Sin. 52, 1259 (2016).Google Scholar
Wu, K., Liu, G.Q., Hu, B.F., Wang, C.Y., Zhang, Y.W., Tao, Y., and Liu, J.T.: Effect of processing parameters on hot compressive deformation behavior of a new Ni–Cr–Co based P/M superalloy. Mater. Sci. Eng., A 528, 4620 (2011).CrossRefGoogle Scholar
Prasad, Y.V.R.K., Sasidhara, S., and Sikka, V.K.: Characterization of mechanisms of hot deformation of as-cast nickel aluminide alloy. Intermetallics 8, 987 (2000).CrossRefGoogle Scholar
Mirzadeh, H., Cabrera, J.M., Prado, J.M., and Najafizadeh, A.: Hot deformation behavior of a medium carbon microalloyed steel. Mater. Sci. Eng., A 528, 3876 (2011).Google Scholar
Meysami, M. and Mousavi, S.A.A.A.: Study on the behavior of medium carbon vanadium microalloyed steel by hot compression test. Mater. Sci. Eng., A 528, 3049 (2011).CrossRefGoogle Scholar
Kim, S-L., Lee, Y., Lee, D-K., and Yoo, T-L.: Modeling of AGS and recrystallized fraction of microalloyed medium carbon steel during hot deformation. Mater. Sci. Eng., A 355, 384 (2003).CrossRefGoogle Scholar
Sellars, C.M. and McTegart, W.J.: On the mechanism of hot deformation. Acta Metall. 14, 1136 (1966).CrossRefGoogle Scholar
Li, H.Z., Wang, H.J., Liang, X.P., Liu, H.T., and Zhang, X.M.: Hot deformation and processing map of 2519A aluminum alloy. Mater. Sci. Eng., A 528(3), 384 (2011).Google Scholar
Han, Y., Liu, G.W., Zou, D.N., Liu, R., and Qiao, G.J.: Deformation behavior and microstructural evolution of as-cast 904L austenitic stainless steel during hot compression. Mater. Sci. Eng., A 565, 342 (2013).Google Scholar
Zhang, P., Li, F., and Wang, Q.: Constitutive equation and processing map for hot deformation of SiC particles reinforced metal matrix composites. J. Mater. Eng. Perform. 19(9), 1290 (2010).Google Scholar
Huang, L.J., Zhang, Y.Z., Liu, B.X., Song, X.Q., Geng, L., and Wu, L.Z.: Superplastic tensile characteristics of in situ TiBw/Ti6Al4V composites with novel network microstructure. Mater. Sci. Eng., A 581, 128 (2013).Google Scholar
Zhao, H.T., Xu, G.Q., and Xu, L.: Rate-controlling mechanisms of hot deformation in a medium carbon vanadium microalloy steel. Mater. Sci. Eng., A 559, 262 (2013).Google Scholar
Mannan, P., Kostryzhev, A.G., Zurob, H., and Pereloma, E.V.: Hot deformation behaviour of Ni–30Fe–C and Ni–30Fe–Nb–C model alloys. Mater. Sci. Eng., A 641, 160 (2015).Google Scholar
Zhu, Y., Feng, W., Sun, Y., Han, Y., and Zhou, Y.: Characterization of hot deformation behavior of as-cast TC21 titanium alloy using processing map. Mater. Sci. Eng., A 582(3), 1757 (2011).Google Scholar
Guo, N.N., Wang, L., Luo, L.S., Li, X.Z., Chen, R.R., and Su, Y.Q.: Hot deformation characteristics and dynamic recrystallization of the MoNbHfZrTi refractory high-entropy alloy. Mater. Sci. Eng., A 651, 698 (2016).CrossRefGoogle Scholar
Kai, X.Z., Chen, C., Sun, X.F., Wang, C.M., and Zhao, Y.T.: Hot deformation behavior and optimization of processing parameters of a typical high-strength Al–Mg–Si alloy. Mater. Des. 90, 1154 (2016).CrossRefGoogle Scholar
Fréour, S., Gloaguen, D., Francois, M., and Guillén, R.: Application of inverse models and XRD analysis to the determination of Ti-17 β-phase coefficients of thermal expansion. Scr. Mater. 54, 1475 (2006).Google Scholar
Prasad, Y.V.R.K. and Seshacharyulu, T.: Processing maps for hot working of titanium alloys. Mater. Sci. Eng., A 243, 82 (1998).Google Scholar
Prasad, Y.V.R.K. and Seshacharyulu, T.: Modelling of hot deformation for microstructural control. Int. Mater. Rev. 43, 243 (1998).Google Scholar
Venugopal, S., Mannan, S.L., and Prasad, Y.V.R.K.: On the development of instability criteria during hotworking with reference to IN 718. Mater. Sci. Eng., A 260, 63 (1993).Google Scholar
Ning, Z.L., Guo, S., Cao, F.Y., Wang, G.J., Li, Z.C., and Sun, J.F.: Microstructural evolution during extrusion and ECAP of a spray-deposited Al–Zn–Mg–Cu–Sc–Zr alloy. J. Mater. Sci. 45, 3023 (2010).Google Scholar
Kong, Y.H., Chang, P.P., Li, Q., Xie, X.L., and Zhu, S.G.: Hot deformation characteristics and processing map of nickel-based C276 superalloy. J. Alloys Compd. 622, 738 (2015).CrossRefGoogle Scholar
Karami, M. and Mahmudi, R.: Hot shear deformation constitutive analysis of an extruded Mg–6Li–1Zn alloy. Mater. Lett. 81, 235 (2012).Google Scholar
Xiao, Z.B., Huang, Y.C., and Liu, Y.: Plastic deformation behavior and processing maps of 35CrMo steel. J. Mater. Eng. Perform. 25(3), 1219 (2016).Google Scholar
Zhou, X.S., Liu, C.X., Yu, L.M., Liu, Y.C., and Li, H.J.: Phase transformation behavior and microstructural control of high-Cr martensitic/ferritic heat-resistant steels for power and nuclear plants: A review. J. Mater. Sci. Technol. 31, 235 (2015).Google Scholar
Lee, W.B., Hong, S.G., Park, C.G., and Park, S.H.: Carbide precipitation and high-temperature strength of hot-rolled high-strength, low-alloy steels containing Nb and Mo. Metall. Mater. Trans. A 33, 1689 (2002).Google Scholar
Furuhara, T. and Maki, T.: Variant selection in heterogeneous nucleation on defects in diffusional phase transformation and precipitation. Mater. Sci. Eng., A 312, 145 (2001).Google Scholar
Gomes, M., Menina, S.F., and Valles, P.: Determination of driving and pinning forces for static recrystallization during hot rolling of a niobium microalloyed steel. ISIJ Int. 45, 1711 (2005).Google Scholar
Prikryl, M., Kroupa, A., Weatherly, G., and Subramanian, S.V.: Precipitation behavior in a medium carbon, ti-v-n microalloyed steel. Metall. Mater. Trans. A 27, 1149 (1996).Google Scholar
Alogab, K., Matlock, D., Speer, J., and Kleebe, H.J.: The influence of niobium microalloying on austenite grain coarsening behavior of Ti-modified SAE 8620 steel. ISIJ Int. 47, 307 (2007).Google Scholar
Fu, L., Wang, H., Wang, W., and Shan, A.D.: Austenite grain growth prediction coupling with drag and pinning effects in low carbon Nb microalloyed steels. Mater. Sci. Technol. 27, 996 (2011).Google Scholar
Alogab, K.A., Matlock, D.K., Speer, J.G. and Kleebe, H.J.: The influence of Niobium microalloyingon austenite grain coarsening behavior of Ti-modified SAE 8620 Steel. ISIJ Int. 47, 307 (2016).Google Scholar
Fernández, A.L., Uranga, P., López, B., and Rodriguez-Ibabe, J.M.: Dynamic recrystallization behavior covering a wide austenite grain size range in Nb and Nb–Ti microalloyed steels. Mater. Sci. Eng., A 361, 372 (2003).Google Scholar