Hostname: page-component-cd9895bd7-q99xh Total loading time: 0 Render date: 2024-12-27T12:00:52.812Z Has data issue: false hasContentIssue false
  • English
  • Français

Hot deformation behavior and processing maps of Ti–6Al–4V alloy with starting fully lamellar structure

Published online by Cambridge University Press:  17 September 2018

Wenjing Zhang ,
Hua Ding ,
Jingwei Zhao ,
Bo Yang  and
Wenjing Yang
Wenjing Zhang
Affiliation:
School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China
Hua Ding*
Affiliation:
School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China
Jingwei Zhao
Affiliation:
School of Mechanical, Materials, Mechatronic and Biomedical Engineering, University of Wollongong, NSW 2522, Australia
Bo Yang
Affiliation:
School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China
Wenjing Yang
Affiliation:
School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China
*
a)Address all correspondence to this author. e-mail: hding@263.net
Get access

Abstract

The hot deformation behavior of Ti–6Al–4V alloy with starting fully lamellar microstructure was investigated by conducting isothermal hot compression tests at the temperature of 700–1000 °C and strain rate of 0.001–10 s−1. The deformation activation energy is calculated to be 342 kJ/mol at temperatures from 750 to 850 °C, whereas the higher apparent activation energy of 610 kJ/mol is obtained at a high temperature regime of 900–1000 °C. The relationship between the dynamic softening behavior and deformation parameters was analyzed by power dissipation efficiency η, which shows an increasing trend as the deformation temperature increases and strain rate decreases, respectively. Processing maps were constructed. The instability flow is dominated by the presence of adiabatic shear bands, and the dynamic softening is mainly caused by a combination effect of dynamic recrystallization and dynamic recovery. Moreover, straining is found to have a positive effect on lowering the phase transformation temperature.

Keywords

Ti–6Al–4V alloyhot deformationactivation energypower dissipation efficiencyprocessing map
Type
Article
Information
Journal of Materials Research , Volume 33 , Issue 22 , 28 November 2018 , pp. 3677 - 3688
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Luo, L., Su, Y., Guo, J., and Fu, H.: Formation of titanium hydride in Ti–6Al–4V alloy. J. Alloys Compd. 425, 140–144 (2006).CrossRefGoogle Scholar
Wang, X., Wang, L., Luo, L., Liu, X., Tang, Y., Li, X., Chen, R., Su, Y., Guo, J., and Fu, H.: Hot deformation behavior and dynamic recrystallization of melt hydrogenated Ti–6Al–4V alloy. J. Alloys Compd. 728, 709–718 (2017).CrossRefGoogle Scholar
Zhang, Z.X., Qu, S.J., Feng, A.H., Shen, J., and Chen, D.L.: Hot deformation behavior of Ti–6Al–4V alloy: Effect of initial microstructure. J. Alloys Compd. 718, 170–181 (2017).CrossRefGoogle Scholar
Zhao, J., Ding, H., Jiang, Z., Huang, M., and Hou, H.: Hydrogen-induced hardening of Ti–6Al–4V alloy in β phase field. Mater. Des. 54, 967–972 (2014).CrossRefGoogle Scholar
Zhao, J., Ding, H., Zhao, W., and Jiang, Z.: Effects of hydrogen on the hot deformation behaviour of Ti–6Al–4V alloy: Experimental and constitutive model studies. J. Alloys Compd. 574, 407–414 (2013).CrossRefGoogle Scholar
Zhao, J., Ding, H., Zhong, Y., and Lee, C.S.: Effect of thermo hydrogen treatment on lattice defects and microstructure refinement of Ti–6Al–4V alloy. Int. J. Hydrogen Energy 35, 6448–6454 (2010).CrossRefGoogle Scholar
Zhang, W.J., Ding, H., Cai, M.H., Yang, W.J. and Li, J.Z.: Ultra-grain refinement and enhanced low-temperature superplasticity in a friction stir-processed Ti–6Al–4V alloy. Mater. Sci. Eng., A 727, 90–96 (2018).CrossRefGoogle Scholar
Roy, S. and Suwas, S.: The influence of temperature and strain rate on the deformation response and microstructural evolution during hot compression of a titanium alloy Ti–6Al–4V–0.1B. J. Alloys Compd. 548, 110–125 (2013).CrossRefGoogle Scholar
Cai, C., Gao, X., Teng, Q., Li, M., Pan, K., Song, B., Yan, C., Wei, Q., and Shi, Y.: A novel hybrid selective laser melting/hot isostatic pressing of near-net shaped Ti–6Al–4V alloy using an in situ tooling: Interfacial microstructure evolution and enhanced mechanical properties. Mater. Sci. Eng., A 717, 95–104 (2018).CrossRefGoogle Scholar
Seshacharyulu, T., Medeiros, S.C., Frazier, W.G., and Prasad, Y.V.R.K.: Hot working of commercial Ti–6Al–4V with an equiaxed α–β microstructure: Materials modeling considerations. Mater. Sci. Eng., A 284, 184–194 (2000).CrossRefGoogle Scholar
Seshacharyulu, T., Medeiros, S.C., Frazier, W.G., and Prasad, Y.V.R.K.: Microstructural mechanisms during hot working of commercial grade Ti–6Al–4V with lamellar starting structure. Mater. Sci. Eng., A 325, 112–125 (2002).CrossRefGoogle Scholar
Semiatin, S.L., Seetharaman, V., and Weiss, I.: Flow behavior and globularization kinetics during hot working of Ti–6Al–4V with a colony alpha microstructure. Mater. Sci. Eng., A 263, 257–271 (1999).CrossRefGoogle Scholar
Shell, E.B. and Semiatin, S.L.: Effect of initial microstructure on plastic flow and dynamic globularization during hot working of Ti–6Al–4V. Metall. Mater. Trans. A 30, 3219–3229 (1999).CrossRefGoogle Scholar
Kim, J.H., Semiatin, S.L., and Lee, C.S.: Constitutive analysis of the high-temperature deformation of Ti–6Al–4V with a transformed microstructure. Acta Mater. 51, 5613–5626 (2003).CrossRefGoogle Scholar
Du, Z., Jiang, S., and Zhang, K.: The hot deformation behavior and processing map of Ti–47.5Al–Cr–V alloy. Mater. Des. 86, 464–473 (2015).CrossRefGoogle Scholar
Zhao, J., Ding, H., Jiang, Z., Wei, D., and Linghu, K.: Effects of hydrogen on the critical conditions for dynamic recrystallization of titanium alloy during hot deformation. Metall. Mater. Trans. A 45, 4932–4945 (2014).CrossRefGoogle Scholar
Peng, X., Guo, H., Shi, Z., Qin, C., and Zhao, Z.: Constitutive equations for high temperature flow stress of TC4-DT alloy incorporating strain, strain rate and temperature. Mater. Des. 50, 198–206 (2013).CrossRefGoogle Scholar
Kim, Y., Song, Y-B., Lee, S.H., and Kwon, Y-s.: Characterization of the hot deformation behavior and microstructural evolution of Ti–6Al–4V sintered preforms using materials modeling techniques. J. Alloys Compd. 676, 15–25 (2016).CrossRefGoogle Scholar
Zhao, J., Ding, H., Zhao, W., Huang, M., Wei, D., and Jiang, Z.: Modelling of the hot deformation behaviour of a titanium alloy using constitutive equations and artificial neural network. Comput. Mater. Sci. 92, 47–56 (2014).CrossRefGoogle Scholar
Shi, C., Mao, W., and Chen, X.G.: Evolution of activation energy during hot deformation of AA7150 aluminum alloy. Mater. Sci. Eng., A 571, 83–91 (2013).CrossRefGoogle Scholar
Ning, Y.Q., Xie, B.C., Liang, H.Q., Li, H., Yang, X.M., and Guo, H.Z.: Dynamic softening behavior of TC18 titanium alloy during hot deformation. Mater. Des. 71, 68–77 (2015).CrossRefGoogle Scholar
Chao, Q., Hodgson, P.D., and Beladi, H.: Ultrafine grain formation in a Ti–6Al–4V alloy by thermomechanical processing of a martensitic microstructure. Metall. Mater. Trans. A 45, 2659–2671 (2014).CrossRefGoogle Scholar
Peng, X., Guo, H., Shi, Z., Qin, C., Zhao, Z., and Yao, Z.: Study on the hot deformation behavior of TC4-DT alloy with equiaxed α + β starting structure based on processing map. Mater. Sci. Eng., A 605, 80–88 (2014).CrossRefGoogle Scholar
Luo, J., Li, M., Li, H., and Yu, W.: Effect of the strain on the deformation behavior of isothermally compressed Ti–6Al–4V alloy. Mater. Sci. Eng., A 505, 88–95 (2009).CrossRefGoogle Scholar
Park, N-K., Yeom, J-T., and Na, Y-S.: Characterization of deformation stability in hot forging of conventional Ti–6Al–4V using processing maps. J. Mater. Process. Technol. 130, 540–545 (2002).CrossRefGoogle Scholar
Seshacharyulu, T., Medeiros, S.C., Morgan, J.T., Malas, J.C., Frazier, W.G., and Prasad, Y.V.R.K.: Hot deformation mechanisms in ELI Grade Ti–6A1–4V. Scr. Mater. 41, 283–288 (1999).CrossRefGoogle Scholar
Momeni, A. and Abbasi, S.M.: Effect of hot working on flow behavior of Ti–6Al–4V alloy in single phase and two phase regions. Mater. Des. 31, 3599–3604 (2010).CrossRefGoogle Scholar
Poletti, C., Warchomicka, F., and Degischer, H.P.: Local deformation of Ti–6Al–4V modified 1 wt% B and 0.1 wt% C. Mater. Sci. Eng., A 527, 1109–1116 (2010).CrossRefGoogle Scholar
Sen, I. and Ramamurty, U.: High-temperature (1023 K to 1273 K [750 °C to 1000 °C]) plastic deformation behavior of B-modified Ti–6Al–4V alloys: Temperature and strain rate effects. Metall. Mater. Trans. A 41, 2959–2969 (2010).CrossRefGoogle Scholar
Raj, S.V. and Pharr, G.M.: A compilation and analysis of data for the stress dependence of the subgrain size. Mater. Sci. Eng., A 81, 217–237 (1986).CrossRefGoogle Scholar
Wen, D-X., Lin, Y.C., Li, H-B., Chen, X-M., Deng, J., and Li, L-T.: Hot deformation behavior and processing map of a typical Ni-based superalloy. Mater. Sci. Eng., A 591, 183–192 (2014).CrossRefGoogle Scholar
Liu, Y., Ning, Y., Yao, Z., and Guo, H.: Hot deformation behavior of Ti–6.0Al–7.0Nb biomedical alloy by using processing map. J. Alloys Compd. 587, 183–189 (2014).CrossRefGoogle Scholar
Chen, H., Liu, X., Liu, G., Tang, X., Luo, J., Feng, Y., Li, J., and Fu, H.: Hot deformation behavior and processing map of Ti–6Al–3Nb–2Zr–1Mo titanium alloy. Rare Met. Mater. Eng. 45, 901–906 (2016).CrossRefGoogle Scholar
Koike, J., Shimoyama, Y., Ohnuma, I., Okamura, T., Kainuma, R., Ishida, K., and Maruyama, K.: Stress-induced phase transformation during superplastic deformation in two-phase Ti–Al–Fe alloy. Acta Mater. 48, 2059–2069 (2000).CrossRefGoogle Scholar
Zhang, W.J., Ding, H., Pereira, P.H.R., Huang, Y., and Langdon, T.G.: Grain refinement and superplastic flow in a fully lamellar Ti–6Al–4V alloy processed by high-pressure torsion. Mater. Sci. Eng., A 732, 398–405 (2018).CrossRefGoogle Scholar
Li, X., Lu, S., Wang, K., Fu, M.W., and Cao, C.: Analysis and comparison of the instability regimes in the processing maps generated using different instability criteria for Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy. Mater. Sci. Eng., A 576, 259–266 (2013).CrossRefGoogle Scholar