Hostname: page-component-78c5997874-s2hrs Total loading time: 0 Render date: 2024-11-15T02:20:38.607Z Has data issue: false hasContentIssue false
  • English
  • Français

Influence of whisker volume fraction on the creep behavior of alumina composites reinforced with silicon carbide

Published online by Cambridge University Press:  03 March 2011

Kenong Xia  and
Terence G. Langdon
Kenong Xia
Affiliation:
Department of Mechanical and Manufacturing Engineering, University of Melbourne, Parkville, Victoria, Australia 3052
Terence G. Langdon
Affiliation:
Departments of Materials Science and Mechanical Engineering, University of Southern California, Los Angeles. California 90089-1453
Get access

Abstract

Four-point bending creep tests were conducted in air on two alumina matrix composites reinforced with 18 and 30 vol% of silicon carbide whiskers, respectively. In both materials, the SiC whiskers tended to form agglomerates. In the temperature range from 1673 to 1823 K, the stress exponents, n, were ∼3.9 and ∼6.3 and the activation energies for creep, Q, were ∼690-740 and ∼930-1010 kJ mol−1 for the composites containing 18 and 30 vol % of SiC, respectively. It is shown that the higher value of n in the composite with 30 vol % of SiC whiskers may be lowered to ∼3 by incorporating a threshold stress. The creep strength of both composites was enhanced by comparison with a similar composite containing 9.3 vol % of SiC whiskers, but there was only a very minor improvement in creep strength when the volume fraction of whiskers was increased from 18 to 30 vol %.

Type
Articles
Information
Journal of Materials Research , Volume 10 , Issue 11 , November 1995 , pp. 2925 - 2932
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Xia, K. and Langdon, T.G., Ada Metall. Mater. 43, 1421 (1995).CrossRefGoogle Scholar
2Chokshi, A. H. and Porter, J. R., J. Am. Ceram. Soc. 68, C144 (1985).CrossRefGoogle Scholar
3Porter, J.R. and Chokshi, A. H., in Ceramic Microstructures '86, edited by Pask, J. A. and Evans, A. G. (Plenum, New York, 1987), p. 919.CrossRefGoogle Scholar
4Lipetzky, P., Nutt, S. R., and Becher, P. F., in High-Temperature/ High-Performance Composites, edited by Lemkey, F. D., Evans, A. G., Fishman, S.G., and Strife, J.R. (Mater. Res. Soc. Symp. Proc. 120, Pittsburgh, PA, 1988), p. 271.Google Scholar
5Nutt, S.R., Lipetzky, P., and Becher, P.F., Mater. Sci. Eng. A126, 165 (1990).CrossRefGoogle Scholar
6de Arellano-López, A. R., Cumbrera, F. L., Domínguez-Rodríguez, A., Goretta, K. C., and Routbort, J.L., J. Am. Ceram. Soc. 73, 1297 (1990).CrossRefGoogle Scholar
7Lin, H-T. and Becher, P. F., J. Am. Ceram. Soc. 73, 1378 (1990).CrossRefGoogle Scholar
8Lipetzky, P., Nutt, S. R., Koester, D. A., and Davis, R. F., J. Am. Ceram. Soc. 74, 1240 (1991).CrossRefGoogle Scholar
9Lin, H-T. and Becher, P.F., J. Am. Ceram. Soc. 74, 1886 (1991).CrossRefGoogle Scholar
10de Arellano-López, A. R., Domínguez-Rodríguez, A., Goretta, K. C., and Routbort, J.L., J. Am. Ceram. Soc. 76, 1425 (1993).CrossRefGoogle Scholar
11Hollenberg, G.W., Terwilliger, G. R., and Gordon, R. S., J. Am. Ceram. Soc. 54, 196 (1971).CrossRefGoogle Scholar
12Cannon, W.R. and Langdon, T.G., J. Mater. Sci. 23, 1 (1988).CrossRefGoogle Scholar
13Chung, D.H. and Simmons, G., J. Appl. Phys. 39, 5316 (1968).CrossRefGoogle Scholar
14Horita, Z. and Langdon, T.G., in Proceedings of the Third International Conference on Creep and Fracture of Engineering Materials and Structures, edited by Wilshire, B. and Evans, R. W. (The Institute of Metals, London, England, 1987), p. 71.Google Scholar
15Sadananda, K. and Feng, C. R., in Advanced Composites '93, edited by Chandra, T. and Dhingra, A. K. (The Minerals, Metals and Materials Society, Warrendale, PA, 1993), p. 603.Google Scholar
16Horita, Z. and Langdon, T.G., Scripta Metall. 17, 665 (1983).CrossRefGoogle Scholar
17Xia, K. and Langdon, T.G., in CompositesɿCorrosion-Coating of Advanced Materials, edited by Kimura, S., Kobayashi, A., Umekawa, S., Nii, K., Saito, Y., and Yoshimura, M. (Mater. Res. Soc. Int. Symp. Proc. 4, Pittsburgh, PA, 1989), p. 185.Google Scholar
18Xia, K. and Langdon, T.G., in Advanced Composites '93, edited by Chandra, T. and Dhingra, A. K. (The Minerals, Metals and Materials Society, Warrendale, PA, 1993), p. 1181.Google Scholar
19Xia, K., Porter, J.R., and Langdon, T.G., in Processing, Fabrication and Manufacturing of Composite Materials, edited by Srivatsan, T. S. and Lavernia, E. J. (American Society of Mechanical Engineers, New York, 1992), p. 253Google Scholar
20Xia, K., Gu, W., and Langdon, T.G., Silicates lndustriels (1995, in press).Google Scholar
21Xia, K. and Langdon, T.G., J. Mater. Sci. Lett. 14, 188 (1995).CrossRefGoogle Scholar