Hostname: page-component-cd9895bd7-gbm5v Total loading time: 0 Render date: 2024-12-29T11:53:05.412Z Has data issue: false hasContentIssue false
  • English
  • Français

Measurement of impact toughness of eutectic SnPb and SnAgCu solder joints in ball grid array by mini-impact tester

Published online by Cambridge University Press:  31 January 2011

Yuhuan Xu ,
Shengquan Ou ,
K.N. Tu ,
Kejun Zeng  and
Rajiv Dunne
Yuhuan Xu
Affiliation:
Department of Materials Science & Engineering, University of California at Los Angeles, Los Angels, California 90095
Shengquan Ou
Affiliation:
Department of Materials Science & Engineering, University of California at Los Angeles, Los Angels, California 90095
K.N. Tu
Affiliation:
Department of Materials Science & Engineering, University of California at Los Angeles, Los Angels, California 90095
Kejun Zeng*
Affiliation:
Texas Instruments, Inc., Dallas, Texas 75265
Rajiv Dunne
Affiliation:
Texas Instruments, Inc., Dallas, Texas 75265
*
a)Address all correspondence to this author. e-mail: k-zeng2@ti.com
Get access

Abstract

The most frequent cause of failure for wireless, handheld, and portable consumer electronic products is an accidental drop to the ground. The impact may cause interfacial fracture of ball-grid-array solder joints. Existing metrology, such as ball shear and ball pull tests, cannot characterize the impact-induced high speed fracture failure. In this study, a mini-impact tester was utilized to measure the impact toughness and to characterize the impact reliability of both eutectic SnPb and SnAgCu solder joints. The annealing effect at 150 °C on the impact toughness was investigated, and the fractured surfaces were examined. The impact toughness of SnAgCu solder joints with the plating of electroless Ni/immersion Au (ENIG) became worse after annealing, decreasing from 10 or 11 mJ to 7 mJ. On the other hand, an improvement of the impact toughness of eutectic SnPb solder joints with ENIG was recorded after annealing, increasing from 6 or 10 to 15 mJ. Annealing has softened the bulk SnPb solder so that more plastic deformation can occur to absorb the impact energy.

Keywords

SolderingPackagingStrength
Type
Articles
Information
Journal of Materials Research , Volume 23 , Issue 5 , May 2008 , pp. 1482 - 1487
Copyright
Copyright © Materials Research Society 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Mishiro, K., Ishikawa, S., Abe, M., Kumai, T., Higashiguchi, Y.Tsubone, K.: Effect of the drop impact on BGA/CSP package reliability. Miroelectr. Reliab. 42, 77 2002CrossRefGoogle Scholar
2Nishiura, M., Nakayama, A., Sakatani, S., Kohara, Y., Uenishi, K.Kobayashi, K.: Mechanical strength and microstructure of BGA joints using leadfree solders. Mater. Trans. 43, 1802 2002CrossRefGoogle Scholar
3Chiu, T-C., Zeng, K., Stierman, R., Edwards, D.Ano, K.: Effect of aging on board level drop reliability for Pb-free BGA packages in Proc. 54th Electr. Compon. Technol. Conf. IEEE Piscataway, NJ 2004 1256–1262Google Scholar
4Zeng, K., Stierman, R., Chiu, T-C., Edwards, D., Ano, K.Tu, K.N.: Kirkendall void formation in eutectic SnPb solder joints on bare Cu and its effect on joint reliability. J. Appl. Phys. 97, 024508 2005CrossRefGoogle Scholar
5Date, M., Shoji, T., Fujiyoshi, M., Sato, K.Tu, K.N.: Ductile-to-brittle transition in Sn–Zn solder joints measured by impact test. Scripta Mater. 51, 641 2004CrossRefGoogle Scholar
6Shoji, T., Yamamoto, K., Kajiwara, R., Morita, T., Sato, K.Date, M.: Proc. 16th JIEP Annual Meeting, Japan Institute of Electronics Packaging 2002 97Google Scholar
7Holt, J.M.: Charpy Impact Test: Factors and Variables ASTM STP 1072, Philadelphia, PA 1990CrossRefGoogle Scholar
8Coyle, R.J., Solan, P.P., Serafino, A.J.Gahr, S.A.: The influence of room temperature aging on ball shear strength and microstructure of area array solder balls in Proc. 50th Electr. Compon. Technol. Conf. IEEE Piscataway, NJ 2000 160Google Scholar
9Chen, Z., He, M.Qi, G.: Morphology and kinetic study of the interfacial reaction between the Sn–3.5Ag solder and electroless Ni–P metallization. J. Electron. Mater. 33, 1465 2004CrossRefGoogle Scholar
10Jang, J.W., Kim, P.G., Tu, K.N., Frear, D.R.Thompson, P.: Solder reaction assisted crystallization of electroless Ni–P under bump metallization in low cost flip chip technology. J. Appl. Phys. 85, 8456 1999CrossRefGoogle Scholar
11Harada, K., Baba, S., Wu, Q., Matsushima, H., Matsunaga, T., Uegai, Y.Kimura, M.: Analysis of solder joint fracture under mechanical bending test in Proc. 53rd Electr. Comp. Technol. Conf. IEEE Piscataway, NJ 2003 1731–1737Google Scholar
12Matsuki, H., Ibuka, H.Saka, H.: TEM observation of interfaces in a solder joint in a semiconductor device. Sci. Technol. Adv. Mater. 3, 261 2002CrossRefGoogle Scholar
13Peng, W., Monlevade, E.Marques, M.E.: Effect of thermal aging on interfacial microstructure and growth of intermetallic compounds between OSP Cu and SnAgCu solder. Microelectr. Reliab. 47, 2161 2007CrossRefGoogle Scholar
14Sohn, Y-C.Yu, J.: Correlation between chemical reaction and brittle fracture found in electroless Ni(P)/immersion gold–solder interconnection. J. Mater. Res. 20, 1931 2005CrossRefGoogle Scholar
15Snugovsky, L., Perovic, D.D.Rutter, J.W.: Experiments on the aging of Sn–Ag–Cu solder alloys. Powder Metall. 48, 193 2005CrossRefGoogle Scholar
16Hwang, C-W., Suganuma, K., Kiso, M.Hashimoto, S.: Interface microstructures between Ni–P alloy plating and Sn–Ag–(Cu) lead-free solders. J. Mater. Res. 18, 2540 2003CrossRefGoogle Scholar
17Zeng, K.Tu, K.N.: Six cases of reliability study of Pb-free solder joints in electronic packaging technology. Mater. Sci. Eng., R 38, 55 2002CrossRefGoogle Scholar
18Kim, H., Zhang, M., Kumar, C.M., Suh, D., Liu, P., Kim, D., Xie, M.Wang, Z.: Improved drop reliability performance with lead free solders of low ag content and their failure modes in Proc. 57th Electron. Comp. Technol. Conf. IEEE Piscataway, NJ 2007 962–967Google Scholar