Hostname: page-component-78c5997874-4rdpn Total loading time: 0 Render date: 2024-11-10T23:29:23.277Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical characterization of secondary-hardening martensitic steel using nanoindentation

Published online by Cambridge University Press:  03 March 2011

T. Ohmura ,
T. Hara ,
K. Tsuzaki ,
H. Nakatsu  and
Y. Tamura
T. Ohmura
Affiliation:
Steel Research Center, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
T. Hara
Affiliation:
Steel Research Center, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
K. Tsuzaki
Affiliation:
Steel Research Center, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
H. Nakatsu
Affiliation:
Metallurgical Research Laboratory, Hitachi Metals, Ltd., Yasugi, Shimane 692-8601, Japan
Y. Tamura
Affiliation:
Metallurgical Research Laboratory, Hitachi Metals, Ltd., Yasugi, Shimane 692-8601, Japan
Get access

Abstract

Mechanical characterizations using nanoindentation technique were performed for the martensitic steel used as practical dies steel containing carbide-former elements of Cr, Mo, W, and V, which are responsible for secondary hardening by tempering. The nanohardness Hn corresponding to the matrix strength shows obvious secondary hardening, and the hardening-peak temperature coincides with that of the macroscale hardness Hv. By comparing the temper-softening behavior of the high-purity Fe–C binary martensite, the ratio of the nanohardness Hn of the dies steel to that of the Fe–C binary steel is approximately a factor of two, whereas the same ratio of the macroscopic hardness Hv is three at the secondary-hardening peak. These results suggest that the secondary hardening of the dies steel during tempering is attributed not only to the nanoscale strengthening factors such as precipitation hardening by the alloy carbides, but also to some other factors in larger scale. One of the strengthening factors in larger scale is a decomposition of 9% retained austenite to much harder phases, such as martensite and/or ferrite–cementite constituent.

Keywords

NanoindentationMicrostructureMechanical properties
Type
Articles
Information
Journal of Materials Research , Volume 19 , Issue 1 , January 2004 , pp. 79 - 84
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Krauss, G., Steels: Heat Treatment and Processing Principles (ASM International, Materials Park, OH, 1989), p. 218.Google Scholar
2.Irvine, K.J. and Pickering, F.B., JISI 194 137 (1960).Google Scholar
3.Grange, R.A., Hribal, C.R. and Porter, L.F., Metall. Trans. 8A 1775 (1977).CrossRefGoogle Scholar
4.Marder, A.R. and Krauss, G., Trans. ASM 60 651 (1967).Google Scholar
5.Marder, J.M. and Marder, A.R., Trans. ASM 62 1 (1969).Google Scholar
6.Marder, A.R. and Krauss, G., Trans. ASM 62 957 (1969).Google Scholar
7.Maki, T., Tsuzaki, K. and Tamura, I., Trans. ISIJ 20 207 (1980).CrossRefGoogle Scholar
8.Ohmura, T., Tsuzaki, K. and Matsuoka, S., Scr. Mater. 45 889 (2001).CrossRefGoogle Scholar
9.Ohmura, T., Tsuzaki, K. and Matsuoka, S., Philos. Mag. A 82 1903 (2002).Google Scholar
10.Ohmura, T., Hara, T. and Tsuzaki, K., J. Mater. Res. 18 1465 (2003).CrossRefGoogle Scholar
11.Oliver, W.C. and Pharr, G.M., J. Mater. Res. 7 1564 (1992).CrossRefGoogle Scholar
12.Itokazu, M. and Murakami, Y., Trans. Jpn. Soc. Mech. Eng. A 59 2560 (1993).CrossRefGoogle Scholar
13.Speich, G.R. and Warlimont, H., J. Iron Steel Inst. 206 385 (1968).Google Scholar
14.Gouldstone, A., Koh, H-J., Zeng, K-Y., Giannakopoulos, A.E. and Suresh, S., Acta Mater. 48 2277 (2000).CrossRefGoogle Scholar