Hostname: page-component-cd9895bd7-gxg78 Total loading time: 0 Render date: 2024-12-28T00:06:40.316Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical properties of iron-based bulk metallic glasses

Published online by Cambridge University Press:  03 March 2011

X.J. Gu ,
S. Joseph Poon  and
Gary J. Shiflet
X.J. Gu
Affiliation:
Department of Physics, University of Virginia, Charlottesville, Virginia 22904-4714
S. Joseph Poon*
Affiliation:
Department of Physics, University of Virginia, Charlottesville, Virginia 22904-4714
Gary J. Shiflet
Affiliation:
Department of Materials Science and Engineering, University of Virginia, Charlottesville, Virginia 22904-4745
*
a) Address all correspondence to this author. e-mail: sjp9x@virginia.edu
Get access

Abstract

Iron-based bulk metallic glasses (BMGs) are characterized by high fracture strengths and elastic moduli, with some exhibiting fracture strengths near 4 GPa, 2–3 times those of conventional high-strength steels. Among the Fe-based BMGs, the non-ferromagnetic ones, designated “non-ferromagnetic amorphous steel alloys” by two of the present authors [S.J. Poon et al.: Appl. Phys. Lett.83, 1131 (2003)], have glass-forming ability high enough to form single-phase glassy rods with diameters reaching 16 mm. Fe-based BMGs designed for structural applications must exhibit some plasticity under compression. However, the role of alloy composition on plastic and brittle failures in metallic glasses is largely unknown. In view of a recently observed correlation that exists between plasticity and Poisson’s ratio for BMGs, compositional effects on plasticity and elastic properties in amorphous steels were investigated. For the new amorphous steels, fracture strengths as high as 4.4 GPa and plastic strains reaching ∼0.8% were measured. Plastic failure instead of brittle failure was observed as the Poisson’s ratio approached 0.32 from below. Investigation of the relationship between the elastic moduli of the alloys and those of the alloying elements revealed that interatomic interactions in addition to the elastic moduli of the alloying elements must be considered in designing ductile Fe-based BMGs. The prospects for attaining high fracture toughness in Fe-based BMGs are discussed in this article.

Keywords

AmorphousElastic propertiesStress/strain relationship
Type
Articles
Information
Journal of Materials Research , Volume 22 , Issue 2 , September 2006 , pp. 344 - 351
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Ponnambalam, V., Poon, S.J., Shiflet, G.J., Keppens, V.M., Taylor, R., and Petculescu, G.: Synthesis of iron-based bulk metallic glasses as nonferromagnetic amorphous steel alloys. Appl. Phys. Lett. 83, 1131 (2003).Google Scholar
2Ponnambalam, V., Poon, S.J., and Shiflet, G.J.: Fe-based bulk metallic glasses with diameter thickness larger than one centimeter. J. Mater. Res. 19, 1320 (2004).CrossRefGoogle Scholar
3Ponnambalam, V., Poon, S.J., and Shiflet, G.J.: Fe–Mn–Cr– Mo–(Y,Ln)–C–B (Ln = lanthanides) bulk metallic glasses as formable amorphous steel alloys. J. Mater. Res. 19, 3046 (2004).Google Scholar
4Lu, Z.P., Liu, C.T., Thompson, J.R., and Porter, W.D.: Structural amorphous steels. Phys. Rev. Lett. 92, 245503 (2004).Google Scholar
5Inoue, A., Shen, B.L., Yavari, A.R., and Greer, A.L.: Mechanical properties of Fe-based bulk glassy alloys in Fe–B–Si–Nb and Fe–Ga–P–C–B–Si systems. J. Mater. Res. 18, 1487 (2003).CrossRefGoogle Scholar
6Inoue, A., Shen, B.L., and Chang, C.T.: Super-high strength of over 4000 MPa in Fe-based bulk glassy alloys in [(Fe1− x Cox )0.75B0.2Si0.05]96Nb4 system. Acta Mater. 52, 4093 (2004).Google Scholar
7Stoica, M., Eckert, J., Roth, S., Zhang, Z.F., Schultz, L., and Wang, W.H.: Mechanical behavior of Fe65.5Cr4Mo4Ga4P12C5B5.5 bulk metallic glass. Intermetallics 13, 764 (2005).CrossRefGoogle Scholar
8Gu, X.J., McDermott, A.G., Poon, S.J., and Shiflet, G.J.: Critical Poisson’s ratio for plasticity in Fe–Mo–C–B–Ln bulk amorphous steel. Appl. Phys. Lett. 88, 211905 (2006).Google Scholar
9Shen, J., Chen, Q., Sun, J., Fan, H., and Wang, G.: Exceptionally high glass-forming ability of an FeCoCrMoCBY alloy. Appl. Phys. Lett. 86, 151907 (2005).CrossRefGoogle Scholar
10Chen, H.S.: Elastic constants, hardness and their implications to flow properties of metallic glasses. J. Non-Cryst. Solids 18, 157 (1975).CrossRefGoogle Scholar
11Lewandowski, J.J., Wang, W.H., and Greer, A.L.: Intrinsic plasticity or brittleness of metallic glasses. Philos. Mag. Lett. 85, 77 (2005).Google Scholar
12Kimura, H. and Masumoto, T.: Strength, ductility and toughness—A study in model mechanics, in Amorphous Metallic Alloys edited by Luborsky, F.E. (Butterworths, Boston, MA, 1983), p. 187.CrossRefGoogle Scholar
13Boll, R., Hilzinger, H.R., and Warlimont, H.: Magnetic material properties and applications of metallic glasses in electronic devices, in Glassy Metals: Magnetic, Chemical, and Structural Properties, edited by Hasegawa, R. (CRC Press, Boca Raton, FL, 1983), p. 183.Google Scholar
14Hess, P.A., Poon, S.J., Shiflet, G.J., and Dauskardt, R.H.: Indentation fracture toughness of amorphous steel. J. Mater. Res. 20, 783 (2005).Google Scholar
15Shen, T.D. and Schwarz, R.B.: Bulk ferromagnetic glasses prepared by flux melting and water quenching. Appl. Phys. Lett. 75, 49 (1999).CrossRefGoogle Scholar
16Migliori, A., Sarrao, J.L., Visscher, W.M., Bell, T.M., Lei, M., Fisk, Z., and Leisure, R.G.: Resonant ultrasound spectroscopic techniques for measurement of the elastic moduli of solids. Physica B (Amsterdam) 183, 1 (1993).Google Scholar
17Zhang, B., Wang, R.J., Zhao, D.G., Pan, M.X., and Wang, W.H.: Properties of Ce-based bulk metallic glass-forming alloys. Phys. Rev. B 70, 224208 (2004).CrossRefGoogle Scholar
18de Boer, F.R., Boom, R., Mattens, W.C.M., Miedema, A.R., and Niessen, A.K.: Cohesion in metals transition metal alloys, in Cohesion and Structure Vol. 1, edited by de Boer, F.R. and Pettifor, D.G. (North Holland, Amsterdam, The Netherlands, 1988).Google Scholar
19Das, J., Tang, M.B., Kim, K.B., Theissmann, R., Baier, F., Wang, W.H., and Eckert, J.: “Work-hardenable” ductile bulk metallic glass. Phys. Rev. Lett. 94, 205501 (2005).Google Scholar
20Yao, K.F., Ruan, F., Yang, Y.Q., and Chen, N.: Superductile bulk metallic glass. Appl. Phys. Lett. 88, 122106 (2006).Google Scholar