The microstructural evolution of ultrathin (<3 nm) oxide films grown on bare Al-based AlMg alloy substrates, by thermal oxidation in the temperature range of 300 to 610 K and at partial oxygen pressures in the range 10−4–10−2 Pa, was investigated by high-resolution transmission electron microscopy. Angle-resolved x-ray photoelectron spectroscopy was applied to establish the chemical constitution of the analyzed oxide films (i.e., the overall Al/Mg cationic ratio, as well as the relative depth distributions of Al and Mg in the grown oxide films). The ˜0.8-nm-thick (Al,Mg)-oxide film grown at 300 K is fully amorphous. A gradual development of long-range order in the oxide film sets in for thickening (Al,Mg)-oxide films of relatively high Mg content at T ≥ 475 K. The amorphous-to-crystalline transition proceeds by a phase separation: still predominantly amorphous oxide regions exist next to crystallized oxide regions, which are constituted of an MgO-type of oxide phase with a face-centered-cubic oxygen sublattice and an average lattice parameter of 4.146 ± 0.1 Å.

Modified embedded-atom method (MEAM) interatomic potentials for Nb-C, Nb-N, Fe-Nb-C, and Fe-Nb-N systems have been developed based on the previously developed MEAM potentials for lower order systems. The potentials reproduce various fundamental physical properties (structural properties, elastic properties, thermal properties, and surface properties) of NbC and NbN, and interfacial energy between bcc Fe and NbC or NbN, in generally good agreement with higher-level calculations or experimental information. The applicability of the present potentials to atomic-level investigations to the precipitation behavior of complex-carbonitrides (Nb,Ti)(C,N) as well as NbC and NbN, and their effects on the mechanical properties of steels are also discussed.

The structure and properties of HfO2 films deposited by plasma assisted reactive pulsed laser deposition and annealed in N2 were studied upon thermal annealing as well as the evaluation of thermal stability by Fourier transform infrared spectroscopy, spectroscopic ellipsometry, and optical transmission measurements. The as-deposited HfO2 films appear predominantly monoclinic with an amorphous matrix which becomes crystallized after high-temperature annealing. No interfacial SiOx is observed for the as-deposited films on Si. The deposited HfO2 films exhibit good thermal stability and show excellent transparency in a wide spectral range with optical band gap energies of 5.65–5.73 eV depending on annealing temperature. An improvement in the optical properties by high-temperature annealing is also observed.

High-pressure in situ angular dispersive x-ray diffraction study on the wurtzite-type InN nanowires has been carried out by means of the image-plate technique and diamond-anvil cell (DAC) up to about 31.8 GPa. The pressure-induced structural transition from the wurtzite to a rocksalt-type phase occurs at about 14.6 GPa, which is slightly higher than the transition pressure of InN bulk materials (∼12.1 GPa). The relative volume reduction at the transition point is close to 17.88%, and the bulk modulus B0 is determined through fitting the relative volume-pressure experimental data related to the wurtzite and rocksalt phases to the Birch–Murnaghan equation of states. Moreover, high-pressure Raman scattering for InN nanowires were also investigated in DAC at room temperature. The corresponding structural transition was confirmed by assignment of phonon modes. We calculated the mode Grüneisen parameters for the wurtzite and rocksalt phases of InN nanowires.

Strontium titanate (SrTiO3) is widely used in electronic devices, and it is a model material for understanding the structural and dielectric properties of grain boundaries (GBs). In such materials, the GBs often play a dominant role in sintering and microstructural behavior. Abnormal grain growth (AGG) is a commonly observed phenomenon. Most studies explained that GBs contain continuous liquid films, and this liquid assists interface diffusion resulting in fast growth. However, few studies investigate the AGG behavior without any liquid. In this study, GB morphology and chemistry have been characterized by high-resolution transmission electron microscopy and x-ray energy-dispersive spectrometry, respectively. Different distributions of GB morphology have been observed in abnormal grains and matrix grains, and GB chemistry varies with different morphological type GBs. By correlating GB morphology and chemistry, a possible mechanism for AGG is proposed.

Electron backscatter diffraction analysis was used to compare the crystal orientation of β-Sn grains in Ni(P)/Sn–0.5Cu/Cu and Ni(P)/Sn–1.8Ag/Cu joints before and after aging. In Ni(P)/solder/Cu joints, the solder composition (Cu versus Ag) significantly affects β-Sn grain orientation. In Ni(P)/Sn–0.5Cu/Cu, there are two types of small columnar grains grown from Ni(P) and Cu under bump metallurgy with a high-angle grain boundary crossing the joint closer to the Ni side; in contrast, Ni(P)/Sn–1.8Ag/Cu has large grains with low-angle boundaries. During thermal aging at 150 °C for 250 h, the Ni(P)/Sn–0.5Cu/Cu joints undergo a more significant microstructural change than the Ni(P)/Sn–1.8Ag/Cu joint. Additionally, obvious ledges developed along the high-angle grain boundary between the upper and lower areas in the Sn–0.5Cu joint.

Co/MnO2 particles are synthesized by a simple two-step chemical process. It includes the reduction of Co2+ cations to Co nanoparticles with sodium borohydride (NaBH4) in aqueous solution, followed by coating the sample with a surface layer of MnO2. The coating is accomplished using a simple decomposition reaction, in aqueous KMnO4 solution with acid environment at room temperature. Transmission electron microscopy (TEM) analysis demonstrates that the core of the particles is composed of Co clusters that have a narrow size distribution. The strong interface effect of the Co/MnO2 particles is also studied by the detection of exchange bias phenomena of hysteresis curves.

Lead barium niobate (PBN or PbxBa1–xNb2O6) is a promising tungsten bronze ceramic system that has a morphotropic phase boundary between the orthorhombic and tetragonal phases at x ≈ 0.63, where the spontaneous polarization (Ps ≈ 60–70 μC/cm2) and other ferroelectric properties are known to be higher. However, even textured PBN60 ceramics have low Ps (∼23.9 μC/cm2) and piezoelectric charge coefficient (d33 ≈ 236 pC/N) as compared to the single crystal counterparts. The aim of this study is to control powder processing, green body formation, and sintering conditions to enhance both densification and electrical properties. Therefore, samples were prepared by tape casting methods using single phase PBN60 and reactive mixture of PbNb2O6 and BaNb2O6 powders. Three wt% excess PbO was found to be necessary for densification. Our results showed that undoped PBN60 ceramics reached Ps = 33 μC/cm2, d33 = 305 pC/N, and had a Tc = 340–350 °C. These results are much higher than the reported values in the literature, which can be attributed to the careful ceramic processing such as tape casting (e.g., homogenous green structure), annealing (e.g., control of excess grain boundary phase), and liquid phase sintering (e.g., higher densification).

BaTiO3 thin films were prepared on metallic foil substrates using chemical solution deposition. The impact of A to B site cation ratios on the phase assemblage and microstructural and dielectric properties was investigated by characterizing a sample set that includes stoichiometric BaTiO3 and 1, 2, 3, 4, and 5 mol% excess BaO. Each composition was subjected to a high-temperature anneal step with maximum dwell temperatures of 1000, 1100, and 1200 °C for 20 h. Excess barium concentrations greater than 3% lead to dramatic grain growth and average grain sizes exceeding 1 μm. Despite the large deviations from stoichiometry and the 20 h dwell time at temperature, x-ray diffraction, and high-resolution electron microscopy analysis were unable to detect secondary phases until films with 5% excess barium were annealed to 1200 °C. Thin films with 3% excess barium were prepared on copper substrates and annealed at 1060 °C, the practical limit for copper. This combination of BaO excess and annealing temperature produced an average lateral grain size of 0.8 μm and a room-temperature permittivity of 4000. This is in comparison to a permittivity of 1800 for stoichiometric material prepared using identical conditions. This work suggests metastable solubility of BaO in BaTiO3 that leads to enhanced grain growth and large permittivity values. This technique provides a new solid-state means of achieving grain growth in low thermal budget systems.

CdS nanocrystals embedded in sodium borosilicate glass were synthesized through sol-gel process. The CdS nanocrystals were usually 10 to 20 nm in size. The microstructure of CdS nanocrystals was determined to be of the hexagonal phase. The morphology and microstructure of the glass were examined using diverse techniques including scanning-probe microscopy (SPM), x-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM), energy dispersion x-ray spectra (EDAX), and high-resolution TEM (HRTEM). The linear optical absorption spectrum of the glass showed a blue shift as a result of quantum-size effect. Furthermore, the third-order optical nonlinearities of the glass were studied by Z-scan technique at a wavelength of 770 nm. The results showed that the third-order optical nonlinear refractive index γ, absorption coefficient β, and susceptibility χ(3) were determined to be −2.16 × 10−16 m2/W, 6.32 × 10−11 m/W, and 1.20 × 10−10 esu, respectively, which were greater than those reported previously for CdS nanocrystals embedded in different matrices.

Using vinyl-silsesquioxane modified with various amounts of tetraethoxysilane (TEOS) and titanium tetrabutoxide (TTB), two kinds of hybrid films, film-vinyl-silsesquioxane-TEOS (f-VSTE) and film-vinyl-silsesquioxane-TTB (f-VSTT), were prepared. The average transparency (AT) of the modified films was measured in the ranges of the visible light region (400–750 nm) and in the near-infrared region (750–2500 nm). The AT values in these ranges are about 88% to 94%, indicating that these high-AT films can provide crops with growth energy and improvement of the photosynthetic process efficiency. The TEOS additions result in a hybrid structure (containing SiO2); an adequate addition can cause an increase in the AT radiation from sunlight. On the other hand, the TTB additions result in a hybrid structure (containing TiO2) that causes a decrease in the AT. These results were validated using molecular dynamic simulation and were calculated (with Materials Stutio software) using the density of states and the energy-band structure of the vinyl-SSO, SiO2, and TiO2 building blocks.

An increasing demand on high energy and power systems has arisen not only with the development of electric vehicle (EV), hybrid electric vehicle (HEV), telecom, and mobile technologies, but also for specific applications such as powering of microelectronic systems. To power those microdevices, an extra variable is added to the equation: a limited footprint area. Three-dimensional (3D) microbatteries are a solution to combine high-density energy and power. In this work, we present the formation of Cu2Sb onto three-dimensionally architectured arrays of Cu current collectors. Sb electrodeposition conditions and annealing post treatment are discussed in light of their influence on the morphology and battery performances. An increase of cycling stability was observed when Sb was fully alloyed with the Cu current collector. A subsequent separator layer was added to the 3D electrode when optimized. Equivalent capacity values are measured for at least 20 cycles. Work is currently devoted to the identification of the causes of capacity fading.

Heteroepitaxial ZnxMg1−xO thin films were grown on lattice-matched MgO (100) substrates using radiofrequency plasma-assisted molecular-beam epitaxy. High-quality epilayers with zinc concentrations ranging from x = 0 (MgO) to x = 0.65 were grown and characterized optically, structurally, and electrically. The ZnxMg1−xO films were found to maintain the rocksalt cubic (B1) crystal structure for concentrations z < 0.65, with a linear dependence of lattice constant on Zn concentration. X-ray diffraction (XRD) also revealed the emergence of phase segregation into wurtzite (B4) phase for the highest concentration film. The band gap energy of the films was successfully varied from 4.9 to 6.2 eV (253–200 nm), showing a linear relationship with Zn concentration. The strictly cubic films exhibit roughness on the order of 10 Å and resistivities of approximately 106 Ω·cm.

Thin titanium films of 200 nm thickness were prepared by physical vapor deposition over conducting glass plates and anodized to form titanium oxide nanostructured film that demonstrates photoactivity under ultraviolet visible (UV-vis) illumination. Absorbance and photoelectrochemical measurements indicate that the anodized and nitrogen annealed films absorb UV-vis (λ = 300 to 800 nm) illumination to produce a current of 2.5 mA at 0 V and 3 mA at +0.4 V versus Ag/AgCl. A photocurrent of 110 μA and an open-circuit photovoltage (VOC) of 300 mV was noted without application of external bias. Long-term stability tests showed that the photocurrent was stable for 2 h under continuous illumination. The titanium oxide prepared from a small fraction of titanium deposited over conducting glass demonstrates almost similar activity compared with titanium oxides prepared on foils. The material offers promising potential in other applications such as environmental remediation and photocatalytic water splitting.

To study the crystallization kinetics of β-Si3N4 in Si–B–C–N polymer-derived ceramics, the amorphous ceramics with composition SiC1.6N1.0B0.4 were synthesized and then isothermally annealed at 1700, 1775 and 1850 °C. The integrated intensities of β-Si3N4 x-ray diffraction (XRD) patterns were used to examine the course of crystallization. The average size of the Si3N4 nanocrystallites was analyzed by means of the XRD measurements and energy-filtering transmission electron microscopy. It was realized that the nanocrystallite dimensions change insignificantly within the time period of crystallization; however, they depend significantly on the temperature. Subsequently, the kinetics of the β-Si3N4 crystallization was analyzed. Consequently, large activation energy in the range of 11.5 eV was estimated. Moreover, continuous nucleation and diffusion-controlled growth have been concluded as the main mechanisms of the crystallization process. Further analysis points at the crucial role of the nucleation rate in the crystallization kinetics of β-Si3N4.

Flowerlike submicrometer gold particles were synthesized through a simple one-step method using p-diaminobenzene as a reductant in the presence of poly(sodium 4-styrenesulfonate) in aqueous solution. The particle size with diameters ranging from 267 to 725 nm could be tuned by varying the molar ratio of poly(sodium 4-styrenesulfonate) to HAuCl4, which also resulted in tunable roughness. The gold particles were confirmed by scanning electron microscopy, energy dispersive x-ray spectroscopy, x-ray diffraction, and x-ray photoelectron spectroscopy. Cyclic voltammetry showed that the specific surface area of the flowerlike particles was larger than that of sphere particles. The obtained flowerlike particles with higher surface area also exhibited higher electrocatalytic activity toward H2O2 and O2. The increase of electrocatalytic activity could be attributed to the increase of the active surface area.

We report the synthesis, characterization, and optical properties of high-temperature stable lanthanide-doped luminescent zirconia nanoparticles via a novel method using carbon black as template. Dopant concentrations were varied from 1 to 5% of Er3+ or Nd3+ and annealing temperatures were varied from 650 to 1100 °C. The effects of the dopant concentration on crystal structure and emission properties were evaluated using x-ray powder diffraction and fluorescence spectroscopy, respectively. The lanthanide cations were found to stabilize the tetragonal phase of zirconia over the monoclinic phase as dopant concentration was increased to 5%. Increasing the annealing temperature to 1100 °C had the opposite effect and was found to stabilize the monoclinic phase of zirconia. The luminescence intensity of the Nd-doped zirconia was enhanced by two orders of magnitude over the undoped or Er-doped zirconia. In all cases, the luminescence spectra revealed increasing intensity with increasing annealing temperature. Zirconia luminescence at near-infrared wavelengths is likely caused by oxygen vacancies. This work demonstrates that the spectral signatures of fluorescent zirconia nanoparticles can be modified with small lanthanide dopant concentration. These particles will have utility in fluorescent sensors and tags, as well as new in refractory materials.

It has been shown that the stability of shear banding and plasticity of bulk metallic glasses (BMGs) can be strongly influenced by the machine stiffness. Here, we demonstrated that the practice of adding a frame parallel to the sample is quantitatively equivalent to increasing the machine stiffness by the frame stiffness. A series of carefully designed experiments were conducted to verify such an effect, showing controllably enhanced plasticity of BMG samples.

This paper demonstrates the production of 〈00l〉-oriented CuO-doped (K0.476Na0.524)NbO3 (KNN) piezoelectric ceramics with a polymorphic phase transition (PPT) temperature greater than 180 °C by templated grain growth (TGG) using high aspect ratio NaNbO3 template particles. A novel (to the KNN system) two-step sintering and annealing process combined with CuO doping is demonstrated to improve density and maximize texture quality (F00l = 99% and rocking curve FWHM = 6.9°) in textured KNN ceramics. The best electromechanical properties (kp ≈ 0.58, k31 ≈ 0.33, d33 ≈ 146 pC/N, To-t ≈ 183 °C, Tc ≈ 415 °C, εr = 202, and tan δ = 0.016) are achieved in 1 mol% CuO-doped KNN with F00l = 99% and a relative density of 96.3%. The values of d33, kp, and k31 are 70–90% higher than randomly oriented ceramics and are obtained without a significant reduction in the PPT temperature, resulting in stable piezoelectric performance over a wide temperature range (−50 to 180 °C). These results show that high-quality textured KNN can be obtained by TGG and that a reactive matrix is unnecessary.

The model of nanosized diamond particles formation at metastable P-T parameters from a C-H-O fluid system is presented. It explains the hydrothermal formation and growth of diamond and the specifics of chemical vapor deposition (CVD) diamond synthesis gas mixtures at low P-T parameters. Further, the model explains the genesis of interstellar nanodiamond formations in space and the genesis of metamorphic microdiamonds in shallow depth Earth rocks. In contrast to models where many possible reactions are considered, the present model makes the simplest possible assumptions about the key processes, and is then able to account for various tendencies seen in experimental data.