Hostname: page-component-78c5997874-g7gxr Total loading time: 0 Render date: 2024-11-10T12:02:38.819Z Has data issue: false hasContentIssue false
  • English
  • Français

Study on Asymmetrical Sheet Rolling by the Finite Element Method

Published online by Cambridge University Press:  05 May 2011

Yeong-Maw Hwang ,
Dyi-Cheng Chen  and
Gow-Yi Tzou
Yeong-Maw Hwang*
Affiliation:
Department of Mechanical Engineering, National Sun Yat-Sen University, Kaohsiung, Taiwan 804, R.O.C.
Dyi-Cheng Chen*
Affiliation:
Department of Mechanical Engineering, National Sun Yat-Sen University, Kaohsiung, Taiwan 804, R.O.C.
Gow-Yi Tzou*
Affiliation:
Department of Mechanical Engineering, Yung Ta Institute of Technology, Ping-Tung, Taiwan 909, R.O.C.
*
*Professor
**Doctor Graduate student
***Associate Professor
Get access

Abstract

Adopting the DEFORM software for the finite element analysis, this study simulated steady-state plastic deformation of the sheet at the roll-gap during asymmetrical sheet rolling. Using FEM code DEFORM, the effects of roll speed ratio, roll radius ratio, friction factor ratio upon the curvature of the rolled product and rolling force were systematically discussed. With a view to verifying the validity of the study simulated, a series of experiments on asymmetrical cold sheet rolling using Aluminum sheet as specimen are carried out. The comparisons between numerical and experimental results show good agreement. Therefore, this numerical model using DEFORM software can offer useful knowledge for designing the pass-schedule of asymmetrical sheet rolling.

Keywords

Finite element methodAsymmetrical sheet rollingCurvature.
Type
Articles
Information
Journal of Mechanics , Volume 15 , Issue 4 , December 1999 , pp. 149 - 155
Copyright
Copyright © The Society of Theoretical and Applied Mechanics, R.O.C. 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Johnson, W. and Needham, G., “Further Experiments in Asymmetrical Rolling,” International Journal of Mechanical Sciences, 8, pp. 443–455 (1966).CrossRefGoogle Scholar
2.Pan, D. and Sansome, D. H., “An Experimental Study of the Effect of Roll Speed Mismatch on the Rolling Load during the Cold Rolling of Thin Strip,” Journal of Mechanical Working Technology, 6, pp. 361–377 (1982).CrossRefGoogle Scholar
3.Pospiech, J., “A Note on the Influence of Some Factors Affecting Curvature in the Flat Rolling of Strip,” Journal of Mechanical Working Technology, 15, pp. 69–80 (1987).CrossRefGoogle Scholar
4.Dewhurst, P., Collins, I. F. and Johnson, W., “A Theoretical and Experimental Investigation into Asymmetical Hot Rolling,” International Journal of Mechanical Sciences, 16, pp. 389–397 (1974).CrossRefGoogle Scholar
5.Green, J. W. and Wallace, J. F., “Estimation of Load and Torque in the Hot Rolling Process,” Journal of Mechanical Engineering Sciences, 4, pp. 136–145 (1962).CrossRefGoogle Scholar
6.Hwang, Y. M. and Tzou, G. Y., “A Analytical Approach to Asymmetrical Cold Strip Rolling Using the Slab Method,” ASM Journal of Material Engineering Perform, 2, pp. 597–606 (1993).CrossRefGoogle Scholar
7.Hwang, Y. M. and Tzou, G. Y., “Analytical and Experimental Study on Asymmetrical Sheet Rolling,” International Journal of Mechanical Sciences, 39, pp. 289–303 (1997).CrossRefGoogle Scholar
8.Hwang, Y. M., “Effects of Rolling Conditions on Bonding Factors in Clad Sheet Rolling — Study on Complex Asymmetrical Rolling III,” Journal of the Japan Society for Technology of Plasticity, 31, pp. 1253–1258 (1990).Google Scholar
9.Richelsen, A. B., “Numerical Analysis of Asymmetrical Rolling Accounting for Differences in Friction,” Journal of Materials Processing Technology, 45, pp. 149–154 (1994).CrossRefGoogle Scholar
10.Richelsen, A. B., “Elastic Plastic Analysis of the Stress and Strain Distributions in Asymmetrical Rolling,” International Journal of Mechanical Sciences, 39, pp. 1199–1211 (1997).CrossRefGoogle Scholar
11.Dyja, H., et al. , “Theoretical and Experimental Analysis of Plates Asymmetrical Rolling,” Journal of Materials Processing Technology, 45, pp. 167–172 (1994).CrossRefGoogle Scholar
12.Cao, G. R., et al. , “Finite Element Simulation of Material Flow in Asymmetrical Rolling Processes,” Advanced Technology of Plasticity — Proceeding of the Fourth International Conference on Technology of Plasticity (1993).Google Scholar
13.Li, G. J. and Kobayashi, S., “Rigid-Plastic Finite Element Analysis of Plane Strain Rolling,” Transactions of the ASME, Journal of Engineering for Industry, 104, pp. 55–64 (1982).CrossRefGoogle Scholar