Automated inclusion microanalysis in steel samples by computer-based scanning electron microscopy provides rapid quantitative information on micro-inclusion distribution, composition, size distribution, morphology, and concentration. Performing the analysis at a lower accelerating voltage (10 kV), rather than the generally used 20 kV, improves analysis accuracy and may improve spatial resolution, but at the cost of a smaller backscattered electron signal and potentially smaller rate of generation of characteristic X-rays. These effects were quantified by simulation and practical measurements.

Atom probe has been developed for investigating materials at the atomic scale and in three dimensions by using either high-voltage (HV) pulses or laser pulses to trigger the field evaporation of surface atoms. In this paper, we propose an atom probe setup with pulsed evaporation achieved by simultaneous application of both methods. This provides a simple way to improve mass resolution without degrading the intrinsic spatial resolution of the instrument. The basic principle of this setup is the combination of both modes, but with a precise control of the delay (at a femtosecond timescale) between voltage and laser pulses. A home-made voltage pulse generator and an air-to-vacuum transmission system are discussed. The shape of the HV pulse presented at the sample apex is experimentally measured. Optimizing the delay between the voltage and the laser pulse improves the mass spectrum quality.

We report on the mitigation of curtaining artifacts during transmission electron microscopy (TEM) lamella preparation by means of a modified ion beam milling approach, which involves altering the incident angle of the Ga ions by rocking of the sample on a special stage. We applied this technique to TEM sample preparation of a state-of-the-art integrated circuit based on a 14-nm technology node. Site-specific lamellae with a thickness <15 nm were prepared by top-down Ga focused ion beam polishing through upper metal contacts. The lamellae were analyzed by means of high-resolution TEM, which showed a clear transistor structure and confirmed minimal curtaining artifacts. The results are compared with a standard inverted thinning preparation technique.

The concept of atomic-scale tomography has been proposed in the past decade as a technique that could deliver the position of all atoms with high precision and their elemental (isotopic) identity. The technique was never intended to be limited to merely structural information and there is clearly a rich array of additional analytical information that can be brought to bear on such tomographs. In this paper, some of these types of information are considered and the implications are explored. The fuller realm of this analytical and structural information may be called atomic-scale analytical tomography.

The semiconductor industry has seen tremendous progress over the last few decades with continuous reduction in transistor size to improve device performance. Miniaturization of devices has led to changes in the dopants and dielectric layers incorporated. As the gradual shift from two-dimensional metal-oxide semiconductor field-effect transistor to three-dimensional (3D) field-effect transistors (finFETs) occurred, it has become imperative to understand compositional variability with nanoscale spatial resolution. Compositional changes can affect device performance primarily through fluctuations in threshold voltage and channel current density. Traditional techniques such as scanning electron microscope and focused ion beam no longer provide the required resolution to probe the physical structure and chemical composition of individual fins. Hence advanced multimodal characterization approaches are required to better understand electronic devices. Herein, we report the study of 14 nm commercial finFETs using atom probe tomography (APT) and scanning transmission electron microscopy–energy-dispersive X-ray spectroscopy (STEM-EDS). Complimentary compositional maps were obtained using both techniques with analysis of the gate dielectrics and silicon fin. APT additionally provided 3D information and allowed analysis of the distribution of low atomic number dopant elements (e.g., boron), which are elusive when using STEM-EDS.

The morphology, composition, and structure of precipitates in an Al–Si–Mg–Hf alloy after heat treatment at 560°C for 20 h were studied by means of Cs-corrected high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), energy dispersive X-ray spectrometry (EDS), high-resolution transmission electron microscopy (HRTEM), and first-principle calculations. Precipitates with three kinds of morphologies were observed. The rectangular and square precipitates were predominantly (Si2−xAlx)Hf phases, while the nanobelt-like precipitate is the Si2Hf phase. First-principle calculations were used to show that the Si6 and Si8 sites were the most favorable sites for Al incorporation in the orthorhombic Si2Hf phase.

Digital image correlation (DIC) in a scanning electron microscope and high-angular resolution electron backscatter diffraction (HREBSD) provide valuable and complementary data concerning local deformation at the microscale. However, standard surface preparation techniques are mutually exclusive, which makes combining these techniques in situ impossible. This paper introduces a new method of applying surface patterning for DIC, namely a urethane microstamp, that provides a pattern with enough contrast for DIC at low accelerating voltages, but is virtually transparent at the higher voltages necessary for HREBSD and conventional EBSD analysis. Furthermore, microstamping is inexpensive and repeatable, and is more suitable to the analysis of patterns from complex surface geometries and larger surface areas than other patterning techniques.

We demonstrate that the surface topography of a sample can be reconstructed from electron backscatter diffraction (EBSD) patterns collected with a commercial EBSD system. This technique combines the location of the maximum background intensity with a correction from Monte Carlo simulations to determine the local surface normals at each point in an EBSD scan. A surface height map is then reconstructed from the local surface normals. In this study, a Ni sample was machined with a femtosecond laser, which causes the formation of a laser-induced periodic surface structure (LIPSS). The topography of the LIPSS was analyzed using atomic force microscopy (AFM) and reconstructions from EBSD patterns collected at 5 and 20 kV. The LIPSS consisted of a combination of low frequency waviness due to curtaining and high frequency ridges. The morphology of the reconstructed low frequency waviness and high frequency ridges matched the AFM data. The reconstruction technique does not require any modification to existing EBSD systems and so can be particularly useful for measuring topography and its evolution during in situ experiments.

Scanning transmission electron microscopy (STEM) in combination with electron energy-loss spectroscopy (EELS) can deliver information about variations of bonding at the nm scale. This is typically performed by analyzing the electron-loss near edge structure (ELNES) of given EELS edges. The present paper demonstrates an alternative way of a bonding examination through monitoring the EELS onset positions. Two conditions are essential for their accurate measurement. One (hardware) is using the dual EELS instrumentation that provides near simultaneous acquisition of low-loss and core-loss spectra. Another (software) is the least-square fitting of observed spectra to a reference spectrum. The combination of these hardware and software techniques reveals the positions of EELS onsets with the precision sufficient for mapping tiny variations of bonding. The paper shows that the method is capable of helping to solve practical tasks of nanoscale engineering like the analysis of modern CMOS devices.

The local electrode atom probe (LEAP) has become the primary instrument used for atom probe tomography measurements. Recent advances in detector and laser design, together with updated hit detection algorithms, have been incorporated into the latest LEAP 5000 instrument, but the implications of these changes on measurements, particularly the size and chemistry of small clusters and elemental segregations, have not been explored. In this study, we compare data sets from a variety of materials with small-scale chemical heterogeneity using both a LEAP 3000 instrument with 37% detector efficiency and a 532-nm green laser and a new LEAP 5000 instrument with a manufacturer estimated increase to 52% detector efficiency, and a 355-nm ultraviolet laser. In general, it was found that the number of atoms within small clusters or surface segregation increased in the LEAP 5000, as would be expected by the reported increase in detector efficiency from the LEAP 3000 architecture, but subtle differences in chemistry were observed which are attributed to changes in the way multiple hit detection is calculated using the LEAP 5000.

Transmission Kikuchi diffraction is an emerging technique aimed at producing orientation maps of the structure of materials with a nanometric lateral resolution. This study investigates experimentally the depth resolution of the on-axis configuration, via a twinned silicon bi-crystal sample specifically designed and fabricated. The measured depth resolution varies from 30 to 65 nm in the range 10–30 keV, with a close to linear dependence with incident energy and no dependence with the total sample thickness. The depth resolution is explained in terms of two mechanisms acting concomitantly: generation of Kikuchi diffraction all along the thickness of the sample, associated with continuous absorption on the way out. A model based on the electron mean free path is used to account for the dependence with incident energy of the depth resolution. In addition, based on the results in silicon, the use of the mean absorption coefficient is proposed to predict the depth resolution for any atomic number and incident energy.

The evolution of the energy dispersive spectrometer (EDS) from the lithium-drifted silicon detector [Si(Li)] to the silicon drift detector (SDD) has created new opportunities in the field of electron probe X-ray microanalysis. The SDD permits operation at significantly higher count rates than the Si(Li) and also provides a more stable energy scale. X-ray spectra captured by EDS can now be analyzed qualitatively or quantitatively under the same beam conditions as used for wavelength dispersive spectrometry (WDS). Standards-based quantitative EDS (SB-Quant-EDS) can thus provide analyses that are accurate and precise for an ever growing number of materials measurement problems. In this study, we analyze NIST research glasses with “known” nominal concentrations of titanium (Ti) and vanadium (V) to evaluate the external reproducibility of the SB-Quant-EDS technique in the presence of severe peak overlaps. We additionally analyze several naturally occurring oxide minerals by WDS and EDS simultaneously and evaluate the outputs of these two methods when quantifying the same analytical volume within the sample.

We present liquid-cell transmission electron microscopy (liquid-cell TEM) imaging of fixed and non-fixed prostate cancer cells (PC3 and LNCaP) with high resolution in a custom developed silicon nitride liquid cell. Fixed PC3 cells were imaged for 90–120 min without any discernable damage. High contrast on the cellular structures was obtained even at low electron doses (~2.5 e−/nm2 per image). The images show distinct structures of cell compartments (nuclei and nucleoli) and cell boundaries without any further sample embedding, dehydration, or staining. Furthermore, we observed dynamics of vesicles trafficking from the cell membrane in consecutive still frames in a non-fixed cell. Our findings show that liquid-cell TEM, operated at low electron dose, is an excellent tool to investigate dynamic events in non-fixed cells with enough spatial resolution (few nm) and natural amplitude contrast to follow key intracellular processes.

There are two main projections used to transform, and reconstruct, field ion micrographs or atom probe tomography data into atomic coordinates at the specimen surface and, subsequently, in three dimensions. In this article, we present a perspective on the strength of the azimuthal equidistant projection in comparison with the more widely used and well-established point projection (or pseudo-stereographic projection), which underpins data reconstruction in most software packages currently in use across the community. After an overview of the reconstruction methodology, we demonstrate that the azimuthal equidistant is more robust with regards to errors on the parameters used to perform the reconstruction and is therefore more likely to yield more accurate tomographic reconstructions.

The capability to perform liquid in situ transmission electron microscopy (TEM) experiments provides an unprecedented opportunity to examine the real-time processes of physical and chemical/electrochemical reactions during the interaction between metal surfaces and liquid environments. This work describes the requisite steps to make the technique fully analytical, from sample preparation, through modifications of the electrodes, characterization of electrolytes, and finally to electrochemical corrosion experiments comparing in situ TEM to conventional bulk cell and microcell configurations.

The bulk of the major core protein VP7 in African horse sickness virus (AHSV) self-assembles into flat, hexagonal crystalline particles in a process appearing unrelated to viral replication. Why this unique characteristic of AHSV VP7 is genetically conserved, and whether VP7 aggregation and particle formation have an effect on cellular biology or the viral life cycle, is unknown. Here we investigated how different small peptide and enhanced green fluorescent protein (eGFP) insertions into the VP7 top domain affected VP7 localization, aggregation, and particle formation. This was done using a dual laser scanning confocal and transmission electron microscopy approach in conjunction with analyses of the solubility, aggregation, and fluorescence profiles of the proteins. VP7 top domain modifications did not prevent trimerization, or intracellular trafficking, to one or two discrete sites in the cell. However, modifications that resulted in a misfolded and insoluble VP7-eGFP component blocked trafficking, and precluded protein accumulation at a single cellular site, perhaps by interfering with normal trimer–trimer interactions. Furthermore, the modifications disrupted the stable layering of the trimers into characteristic AHSV VP7 crystalline particles. It was concluded that VP7 trafficking is driven by a balance between VP7 solubility, trimer forming ability, and trimer–trimer interactions.

We trace Sn nanoparticles (NPs) produced from SnO2 nanotubes (NTs) during lithiation initialized by high energy e-beam irradiation. The growth dynamics of Sn NPs is visualized in liquid electrolytes by graphene liquid cell transmission electron microscopy. The observation reveals that Sn NPs grow on the surface of SnO2 NTs via coalescence and the final shape of agglomerated NPs is governed by surface energy of the Sn NPs and the interfacial energy between Sn NPs and SnO2 NTs. Our result will likely benefit more rational material design of the ideal interface for facile ion insertion.