The performance of the pulsed-laser atom probe can be limited by both instrument and specimen factors. The experiments described in this article were designed to identify these factors so as to provide direction for further instrument and specimen development. Good agreement between voltage-pulsed and laser-pulsed data is found when the effective pulse fraction is less than 0.2 for pulsed-laser mode. Under the conditions reported in this article, the thermal tails of the peaks in the mass spectra did not show any significant change when produced with either a 10-ps or a 120-fs pulsed-laser source. Mass resolving power generally improves as the laser spot size and laser wavelength are decreased and as the specimen tip radius, specimen taper angle, and thermal diffusivity of the specimen material are increased. However, it is shown that two of the materials used in this study, aluminum and stainless steel, depend on these factors differently. A one-dimensional heat flow model is explored to explain these differences. The model correctly predicts the behavior of the aluminum samples, but breaks down for the stainless steel samples when the tip radius is large. A more accurate three-dimensional model is needed to overcome these discrepancies.

Extended abstract of a paper presented at MC 2007, 33rd DGE Conference in Saarbrücken, Germany, September 2 – September 7, 2007

Transmission electron microscopy (TEM) studies in the 1960s and early 1970s using conventional thin section and freeze fracture methodologies revealed ultrastructural bacterial spore appendages. However, the limited technology at that time necessitated the time-consuming process of imaging serial sections and reconstructing each structure. Consequently, the distribution and function of these appendages and their possible role in colonization or pathogenesis remained unknown. By combining high resolution field emission electron microscopy with TEM images of identical bacterial spore preparations, we have been able to obtain images of intact and sectioned Bacillus and Clostridial spores to clearly visualize the appearance, distribution, resistance (to trypsin, chloramphenicol, and heat), and participation of these structures to facilitate attachment of the spores to glass, agar, and human cell substrates. Current user-friendly commercial field emission scanning electron microscopes (FESEMs), permit high resolution imaging, with high brightness guns at lower accelerating voltages for beam sensitive intact biological samples, providing surface images at TEM magnifications for making direct comparisons. For the first time, attachment structures used by pathogenic, environmental, and thermophile bacterial spores could be readily visualized on intact spores to reveal how specific appendages and outer spore coats participated in spore attachment, colonization, and invasion.

Extended abstract of a paper presented at Microscopy and Microanalysis 2007 in Ft. Lauderdale, Florida, USA, August 5 – August 9, 2007

We demonstrate a new sensitive biosensor for detection of vital fungal spores of Aspergillus niger. The biosensor is based on silicon microfabricated cantilever arrays operated in dynamic mode. The change in resonance frequency of the sensor is a function of mass binding to the cantilever surface. For specific A. niger spore immobilization on the cantilever, each cantilever was individually coated with anti-Aspergillus niger polyclonal antibodies. We demonstrate the detection of single A. niger spores and their subsequent growth on the functionalized cantilever surface by online measurements of resonance frequency shifts. The new biosensor operating in humid air allows quantitative and qualitative detection of A. niger spores as well as detection of vital, functional spores in situ within ∼4 h. The detection limit of the sensor is 103 CFU mL−1. Mass sensitivity of the cantilever sensor is ∼53 pg Hz−1.

Focused ion beam specimen preparation has been used for NiTi samples and SrTiO3/SrRuO3 multilayers with prevention of surface amorphization and Ga implantation by a 2-kV cleaning procedure. Transmission electron microscopy techniques show that the samples are of high quality with a controlled thickness over large scales. Furthermore, preferential thinning effects in multicompounds are avoided, which is important when analytical transmission electron microscopy measurements need to be interpreted in a quantitative manner. The results are compared to similar measurements acquired for samples obtained using conventional preparation techniques such as electropolishing for alloys and ion milling for oxides.

Registration form.

Extended abstract of a paper presented at Microscopy and Microanalysis 2007 in Ft. Lauderdale, Florida, USA, August 5 – August 9, 2007

Extended abstract of a paper presented at MC 2007, 33rd DGE Conference in Saarbrücken, Germany, September 2 – September 7, 2007.

Micro-focused synchrotron radiation techniques to investigate actinide elements in geological samples are becoming an increasingly used tool in nuclear waste disposal research. In this article, results using μ-focus techniques are presented from a bore core section of a U-rich tertiary sediment collected from Ruprechtov, Czech Republic, a natural analog to nuclear waste repository scenarios in deep geological formations. Different methods are applied to obtain various, complementary information. Elemental and element chemical state distributions are obtained from μ-XRF measurements, oxidation states of As determined from μ-XANES, and the crystalline structure of selected regions are studied by means of μ-XRD. We find that preparation of the thin section created an As oxidation state artifact; it apparently changed the As valence in some regions of the sample. Results support our previously proposed hypothesis of the mechanism for U-enrichment in the sediment. AsFeS coating on framboid Fe nodules in the sediment reduced mobile groundwater-dissolved U(VI) to less-soluble U(IV), thereby immobilizing the uranium in the sediment.

Human cadaveric skin allografts are used in the treatment of burns and can be preserved in glycerol at high concentrations. Previously, glycerol has been attributed some antimicrobial effect. In an experimental set-up, we aimed at investigating this effect of prolonged incubation of bacteria in 85% glycerol. Staphylococcus epidermidis, Staphylococcus aureus, Pseudomonas aeruginosa, and Bacillus subtilis were incubated in 85% glycerol. The influence of duration of incubation and temperature on ultrastructure and viability were investigated. Unstressed cultures served as controls. Survival was studied after 24–36 h and 10 days incubation in 85% glycerol at 4°C and 36°C with transmission electron microscopy (TEM) and flow cytometry using viability stains indicating membrane damage (SYTO9, propidium iodide) or esterase activity (carboxyfluorescein diacetate). TEM clearly demonstrated variability in morphological changes of bacteria suggesting different mechanisms of damage. Viability stains supported these findings with faster declining viable cell populations in 85% glycerol at 36°C compared with 4°C. Both methods demonstrated that Gram-negative species were more susceptible than Gram-positive species. In conclusion, 85% glycerol may have some additional antimicrobial effect. Temperature is an important factor herein and Gram-negatives are most susceptible. The latter finding probably reflects the difference in cell wall composition between Gram-positive and Gram-negative bacteria.

Registration.

Cancellation policy.

Commercial exhibits.

Important events during the meeting.

Pre-meeting events.

Microscopy and Microanalysis workshop.

MSA MegaBooth.

Business and committee meetings.

Awards.

Poster awards

Future Microscopy and Microanalysis meetings.

Poster instructions.

Late breaking poster sessions.

Security requirements for Convention Center access.

Hotel descriptions.

We have applied high-angle annular dark-field microscopy to the characterization of the structure of template-grown nanotubes composed of a polymer and a discotic liquid crystalline material. Selective staining of the liquid crystal phase with ruthenium tetroxide was used to develop adequate Z-contrast that allows us to distinguish between the two phases. At appropriate staining conditions, we could clearly visualize, in the annular dark-field mode, a 5–15-nm thin liquid crystalline layer precipitated on the inner surface of the polymer tubes. Cryo-electron diffraction has shown high alignment of the discotic columns within the layer parallel to the tube axis. However, although the polymer/liquid crystal phase separation is almost complete, the wetting behavior of the polymer in relation to the template appears to be sensitively influenced by kinetic factors.

A growing problem in cardiac drug toxicity has been blamed on the lack of adequate testing prior to authorization for prescription use. This study offers an effective alternative to the current method of in vivo pharmaceutical testing, which is time and cost prohibitive. We have accomplished this by developing the novel three-dimensional heart tube model. At the “heart” of our model lies our patented collagen scaffold that enables the cardiac myocytes to display an in vivo–like architecture. The cardiac myocytes were cocultured with the collagen tube for a period of 5 weeks, resulting in the heart tubes. Our heart tubes were treated with specific drugs (nifedipine, isoproterenol, and lidocaine) at varying concentrations. The percent of apoptotic cells was calculated based on observing the number of cells that labeled positive for caspase-3 via confocal microscopy. All three drugs exhibited negative effects at high concentrations in that the number of living cells decreased. Lidocaine showed an increase in apoptosis at concentrations of 75 μM and above. This may indicate that certain drugs have a minimum concentration level that must be reached before the cells experience apoptosis from the toxic levels.

Several FIB-based methods that have been developed to fabricate needle-shaped atom probe specimens from a variety of specimen geometries, and site-specific regions are reviewed. These methods have enabled electronic device structures to be characterized. The atom probe may be used to quantify the level and range of gallium implantation and has demonstrated that the use of low accelerating voltages during the final stages of milling can dramatically reduce the extent of gallium implantation.

A new type of positive electrode for Li-ion batteries has been developed recently based on FeF3/C and FeF2/C nanocomposites. The microstructural and redox evolution during discharge and recharge processes was followed by electron energy loss spectroscopy (EELS) to determine the valence state of Fe by measuring the Fe L3 line energy shift and from Fe L3/L2 line intensity ratios. In addition, transition metal fluorides were found to be electron beam sensitive, and the effect of beam exposure on EELS spectra was also investigated. The EELS results indicate that for both FeF3/C and FeF2/C nanocomposite systems, a complete reduction of iron to FeO is observed upon discharge to 1.5 V with the formation of a finer FeO/LiF subnanocomposite (∼7 nm). Upon complete recharging to 4.5 V, EELS data reveal a reoxidation process to a Fe2+ state with the formation of a carbon metal fluoride nanocomposite related to the FeF2 structure.

In the present article, electron probe microanalysis data for Pu and Nd is being used for validating the predictions of the radial power profile in a nuclear fuel rod at an ultrahigh burn-up of 95 and 102 MWd/kgHM. As such the validation of both the new Monte Carlo burn-up code ALEPH and the simpler TUBRNP model of the fuel rod performance code TRANSURANUS has been extended. The analysis of the absolute concentrations and individual isotopes also indicates potential improvements in the predictive capabilities of the simple TUBRNP model, based on the one-group cross sections inferred from the neutron transport calculations in the ALEPH code. This is a first important step toward extending the application range of the fuel rod performance code to burn-up values projected in nuclear power rods based on current trends.

Extended abstract of a paper presented at Microscopy and Microanalysis 2007 in Ft. Lauderdale, Florida, USA, August 5 – August 9, 2007

Extended abstract of a paper presented at MC 2007, 33rd DGE Conference in Saarbrücken, Germany, September 2 – September 7, 2007

The effect of peripheral halogenation is examined based on analytical transmission electron microscopy and thermal analyses of two chemical family structures, specifically the vanadyl-phthalocyanine family (VOPcX: X = H16, F14.5) and the copper-phthalocyanine family (CuPcX: X = H16, F16, Cl16, Cl8Br8), focusing on the process of molecular changes and crystalline disintegrations. To clarify the molecular transformations, electron energy-loss spectroscopy (EELS) is applied to two fluorinated phthalocyanines (VOPcF14.5 and CuPcF16), by monitoring mass changes as well as energy loss near edge structures (ELNES). The elemental mass of both VOPcF14.5 and CuPcF16 remain constant up to 0.5 C·cm−2, except in the case of mass reduction attributed to oxygen loss occurring in VOPcF14.5. It is expected that the released oxygen will induce higher radiation damage in VOPcF14.5. Although mass variation is not observed in CuPcF16, it is found from ELNES that the π resonant system of nitrogen is more radiation sensitive than that of carbon. These results imply that the electron sensitivity in VOPcX is triggered by eliminated oxygen or, thus, an induced larger empty space, whereas the sensitivity of CuPcX is dominated only by a large intermolecular empty space resulting in the following bond alterations. It is also found that the decomposition temperature (Td) measured by thermal analyses and the characteristic dose (D1/e) are exponentially correlated to the “effective molecular occupancy” (Oe) evaluated as a volume function of molecules in unit cells. By measuring Td and/or Oe, we discuss the durability of peripheral halogenation with respect to the radiation damage.