Hostname: page-component-78c5997874-fbnjt Total loading time: 0 Render date: 2024-11-11T01:51:20.606Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of Poly(ε-Caprolactone) as a bio-lubricant additive in AISI 4140 Steel/Al2O3 tribosystem

Published online by Cambridge University Press:  11 October 2019

María T. Hernández-Sierra Open the ORCID record for María T. Hernández-Sierra [Opens in a new window] ,
Micael G. Bravo-Sánchez ,
Luis D. Aguilera-Camacho ,
José E. Báez ,
J.S. García-Miranda  and
Karla J. Moreno
María T. Hernández-Sierra*
Affiliation:
Tecnológico Nacional de México en Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México.
Micael G. Bravo-Sánchez
Affiliation:
Tecnológico Nacional de México en Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México.
Luis D. Aguilera-Camacho
Affiliation:
Tecnológico Nacional de México en Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México.
José E. Báez
Affiliation:
Facultad de Química, Universidad de Guanajuato, Noria Alta S/N, 36050-Guanajuato, Guanajuato, México.
J.S. García-Miranda
Affiliation:
Tecnológico Nacional de México en Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México.
Karla J. Moreno
Affiliation:
Tecnológico Nacional de México en Celaya, Apartado Postal 57, 38010-Celaya, Guanajuato, México.
*
*(Email: tere.mths@hotmail.com)
Get access

Abstract

Since ancient times, lubricants have been used to reduce friction and wear problems of mechanical systems. However, nowadays, there is a constant effort to improve their performance through additives so that they can accomplish properly in this modern world. In that sense, in this study, it was proposed the use of Poly(ε-Caprolactone) (PCL) as a biodegradable additive in Castor oil. The effect that this additive has on the tribological properties of AISI 4140 steel/Al2O3 tribosystem was analyzed. For this purpose, PCL was dissolved in Castor oil at 65 °C for 15 minutes. Later, once the lubricant formulations got into room temperature, friction tests were conducted with a ball-on-disk configuration. Several experiments were systematically carried out in order to study the factors that could influence the performance of the tribological system, for instance: additive concentration, velocity, temperature, and wear track radius. The kinetic friction coefficient was used to analyze the results as an output variable. The parameters in which the best friction behavior was observed were employed again to compare the efficiency of the polymeric additive by profoundly analyzing and comparing the wear response of the system. The PCL additive showed great results by decreasing friction up to 30% compared to the neat Castor oil. Nevertheless, as the opposite effect, this additive increased the steel wear to almost half an order of magnitude. Given the above, this investigation showed that, with further studies, Poly(ε-Caprolactone) could be used as an additive in vegetable oil-based lubricants for the improvement of friction performance.

Keywords

polymeradditiveslubricanttribologysteel
Type
Articles
Information
MRS Advances , Volume 4 , Issue 57-58: International Materials Research Congress XXVIII , 2019 , pp. 3105 - 3112
Copyright
Copyright © Materials Research Society 2019 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

References:

Wang, H., Qian, S., Ni, Z., Huang, C., and Zhao, Y., P. I. Mech. Eng. J - J. Eng. Trib. 232(7), 861-870 (2017).Google Scholar
Hernández-Sierra, M.T., Ortega-Álvarez, R., Bravo-Sánchez, M.G., Aguilera-Camacho, L.D., García-Miranda, J.S., and Moreno, K., MRS Advances 2(62), 3873-3881 (2017).CrossRefGoogle Scholar
Zeng, Q.F. and Dong, G.N., Trans. Nonferrous Met. Soc. China 24, 354-359 (2014).CrossRefGoogle Scholar
Wang, Y., Wan, Z., Lu, L., Zhang, Z., and Tang, Y., Trib. Int. 124, 10-22 (2018).CrossRefGoogle Scholar
Gupta, R.N., Harsha, A.P., and Mech, P.I.. Eng. J - J. Eng. Trib. 232(9), 1055-1067 (2018).Google Scholar
Bhaumik, S., Maggirwar, R., Datta, S., and Pathak, S.D., Appl. Surf. Sci. 449, 277-286 (2018).CrossRefGoogle Scholar
Borrero-López, A.M., Santiago-Medina, F.J., Valencia, C., Eugenio, M.E., Martin-Sampedro, R., and Franco, J.M., J. Renew. Mater. 6 (4), 347-361 (2018).CrossRefGoogle Scholar
Bhaumik, S., Mathew, B.R., and Datta, S., Fuel 241, 733-743 (2019).CrossRefGoogle Scholar
Chen, T., Ji, J., and Jin, Q., e-Polymers 15(1), 3-13 (2015).CrossRefGoogle Scholar
Guo, J., Mei, T., Li, Y., Ren, S., Hafezi, M., Lu, H., Li, Y., and Dong, G., Mater. Res. Express 5, 065315 (2018).CrossRefGoogle Scholar
Báez, J.E., Martínez-Rosales, M., and Martínez-Richa, A., Polymer 44(22), 6767-6772 (2003).CrossRefGoogle Scholar
Hernández-Sierra, M.T., Aguilera-Camacho, L.D., Báez-García, J.E., García-Miranda, J.S., and Moreno, K.J., Metals 8(6), 428 (2018).CrossRefGoogle Scholar
Hamrock, B.J., Schmid, S.R., and Jacobson, B.O., in Fundamental of Fluid Film Lubrication, edited by Hamrock, B.J., Schmid, S.R., and Jacobson, B.O. (Marcel Dekker, Inc., New York, 2004) p. 22-43.CrossRefGoogle Scholar
Kenbeck, D. and Bunemann, T.F., in Lubricant Additives: Chemistry and Applications, edited by Rudnick, L.R. (CRC Press Taylor & Francis Group, Boca Raton, 2017), p. 87-97.CrossRefGoogle Scholar