Hostname: page-component-cd9895bd7-p9bg8 Total loading time: 0 Render date: 2024-12-27T13:29:58.370Z Has data issue: false hasContentIssue false
  • English
  • Français

Porous Ti–Al Intermetallic Based Alloys Fabricated by Pressure-Sintering Elemental Powders with a Space Holder Powder

Published online by Cambridge University Press:  30 January 2017

Naoki Takata ,
Keisuke Uematsu  and
Makoto Kobashi
Naoki Takata*
Affiliation:
Dept. Materials Science and Engineering, Nagoya University, Nagoya, 464-8603, Japan
Keisuke Uematsu
Affiliation:
Dept. Materials Science and Engineering, Nagoya University, Nagoya, 464-8603, Japan
Makoto Kobashi
Affiliation:
Dept. Materials Science and Engineering, Nagoya University, Nagoya, 464-8603, Japan
*
*(Email: takata@numse.nagoya-u.ac.jp)
Get access

Abstract

In the present study, we have attempted to produce the porous Ti–Al intermetallic based alloys by pressure-sintering of the elemental powders of Ti and Al through a combustion reaction, with a NaCl space holder to achieve the development of a highly porous structure. The powders of Ti (particle size: <45 μm) and Al (particle size: <45 μm) were mixed to various total compositions of Ti–0-40 Al (at.%), and NaCl (particle size: 300-400 μm) was mixed with the Ti/Al powder to give a highly porous structure. The mixed powder was sintered at 700 oC under a constant pressure of 30 MPa to form cylindrical specimens with a diameter of 20 mm. The soaking of the specimens in pure water allows for the removal of NaCl (with a volume fraction of 60 %) and the formation of the pores to achieve a controlled relative density of 0.4. The present process can produce porous Ti–Al alloys with various compositions. In as-sintered Ti–Al specimens, an inhomogeneous microstructure consisting of Ti particles surrounded by the a Ti–Al alloy layer (various Ti–Al intermetallic phases) was observed. The as-sintered specimens exhibited the brittle behavior under compression, which is independent of their Al content. However, in a Ti–20Al alloy heat-treated at 1300 °C, a nearly Ti3Al single-phase microstructure appeared in the porous specimen. The heat-treated porous Ti–20Al alloy shows both a high plateau-strength level of approximately 100 MPa and a high plateau-end strain over 50%, resulting in a high absorption energy. The present results demonstrate that controlling the microstructure for the formation of the Ti3Al single-phase would be an effective method to achieve high energy absorption capacity of the porous Ti–Al alloy.

Keywords

powder processingcombustion synthesismicrostructure
Type
Articles
Information
MRS Advances , Volume 2 , Issue 26: Mechanical Behavior and Failure Mechanisms of Materials , 2017 , pp. 1387 - 1392
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Ashby, M. F., Evans, A., Fleck, N. A., Hutchinson, J. W., Wadley, H.N.G., Metals Foams : A Design Guide, Elsevier Science (2000).Google Scholar
Banhart, J., Prog. Mater. Sci. 46, 559 (2001).Google Scholar
Lefebvre, L.-P., Banhart, J. and Dunand, D., Adv. Eng. Mater. 10, 775 (2008).Google Scholar
Banhart, J., Adv. Eng. Mater. 15, 82 (2013) .Google Scholar
Koza, E., Leonowicz, M., Wojciechowski, S., Simancik, F., Mater. Let. 58, 132 (2003).Google Scholar
Kanetake, N., Kobashi, M., Journal of The Japan Institute of Light Metals 62, 122 (2012).Google Scholar
Lasalmonie, A., Intermetallics, 14 1123 (2006).Google Scholar
Wu, X., Intermetallics 14 1114 (2006).Google Scholar
Gaillard, C., Despois, J. F., Mortensen, A., Mater. Sci. Eng. A 374, 250 (2004).Google Scholar
Torres, Y., Pavon, J. J., Rodriguez, J. A., J Mater. Proc. Tech. 212, 1061 (2012).Google Scholar
Wenjuan, N., Chenguang, B., GuiBao, Q., Qiang, W., Mater. Sci. Eng. A 506, 148 (2009).Google Scholar
Kobashi, M., Miyake, S., Kanetake, N., Intermetallics 42, 32 (2013).Google Scholar
Kobashi, M., Inoguchi, N., Kanetake, N., Intermetallics 18, 1039 (2010).CrossRefGoogle Scholar
Arakawa, Y., Kobashi, M., Kanetake, N., Intermetallics 41, 22 (2013).Google Scholar
Mansourighasri, A., Muhamad, N., Sulong, A.B., J. Mater. Proc. Tech. 212, 83 (2012).Google Scholar
Liu, Y., Li, S., Hou, W., Wang, S., Hao, Y., Yang, R., Sercombe, T. B., Zhang, L.-C., J. Mater. Sci. Tech. 32, 505 (2016).CrossRefGoogle Scholar
Jha, N., Mondal, D.P., Majumdar, J. D, Badkul, A., Jha, A.K., Khare, A.K., Materials and Design 47, 810 (2013).Google Scholar
Lipsitt, H. A., Shechtman, D. S., Schafrik, R. E., Metall. Trans. A 11, 1369 (1980).Google Scholar
Inui, H., Toda, Y., Shirai, Y., Yamaguchi, M., Philos. Mag. A 69, 1161(1994).Google Scholar
Minonishi, Y., Philos. Mag. A 63, 1085 (1991).Google Scholar
Umakoshi, Y., Nakano, T., Ogawa, B., Scr. Mater. 34, 1161 (1996).Google Scholar
Naruse, W., Kondo, S., Kobashi, M., Kanetake, N., Iwata, Y., Nishiwaki, T., Journal of The Japan Institute of Light Metals 64, 598 (2014).Google Scholar