Hostname: page-component-cd9895bd7-lnqnp Total loading time: 0 Render date: 2024-12-27T13:24:41.810Z Has data issue: false hasContentIssue false
  • English
  • Français

Processing parameter, microstructure and hardness of Ni base intermetallic alloy coating fabricated by laser cladding

Published online by Cambridge University Press:  30 January 2017

Takeshi Okuno ,
Yasuyuki Kaneno ,
Takuto Yamaguchi ,
Takayuki Takasugi ,
Satoshi Semboshi  and
Hideki Hagino
Takeshi Okuno*
Affiliation:
Department of Materials Science, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 5998531, Japan
Yasuyuki Kaneno
Affiliation:
Department of Materials Science, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 5998531, Japan
Takuto Yamaguchi
Affiliation:
Technology Research Institute of Osaka Prefecture, 2-7-1 Ayumino, Izumi, Osaka 5941157, Japan
Takayuki Takasugi
Affiliation:
Department of Materials Science, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 5998531, Japan
Satoshi Semboshi
Affiliation:
Trans-Regional Corporation Center, Institute for Materials Research, Tohoku University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 5998531, Japan
Hideki Hagino
Affiliation:
Technology Research Institute of Osaka Prefecture, 2-7-1 Ayumino, Izumi, Osaka 5941157, Japan
*
*(Email: sv110012@edu.osakafu-u.ac.jp)
Get access

Abstract

Ni base intermetallic alloy coating was fabricated by laser cladding, controlling the laser power and powder feed rate. Atomized powder of the Ni base intermetallic alloy was laser-cladded on the substrate of stainless steel 304. The hardness and microstructure of the clad layers were investigated by Vickers hardness test, SEM, XRD and TEM observations. The hardness of the cladding layer was affected by the dilution with the substrate; it increased with decreasing laser power and increasing powder feed rate. By optimizing the dilution with the substrate, the cladding layer with an almost identical hardness level to that of the Ni base intermetallic alloy fabricated by ingot metallurgy was obtained. The TEM observations revealed that a very fine-sized microstructure composed of Ni3Al and Ni3V was partially formed even in the as-cladded state. After annealing, the two-phase microstructure composed of Ni3Al and Ni3V was developed in the cladding layer, resulting in enhanced hardness in the cladding layers fabricated in the majority of cladding conditions.

Keywords

hardnessmicrostructurex-ray diffraction (XRD)
Type
Articles
Information
MRS Advances , Volume 2 , Issue 26: Mechanical Behavior and Failure Mechanisms of Materials , 2017 , pp. 1381 - 1386
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Nunomura, Y., Kaneno, Y., Tsuda, H., Takasugi, T., Acta Mater. 54 (2006) 851–860.CrossRefGoogle Scholar
Shibuya, S., Kaneno, Y., Yoshida, M., Takasugi, T., Acta Mater. 54 (2006) 861–870.CrossRefGoogle Scholar
Shibuya, S., Kaneno, Y., Tsuda, H., Takasugi, T., Intermetallics 15 (2007) 338–348.CrossRefGoogle Scholar
Kawahara, K., Kaneno, Y., kakitsuji, A., Takasugi, T., Intermetallics 17 (2009) 938–944.CrossRefGoogle Scholar
Li, YX, Liu, Y, Geng, HY, Nie, DK, J Mater Process Technol. 171 (2006) 405–410.CrossRefGoogle Scholar
Yu, Y., Zhou, J., Chen, J., Zhou, H., Guo, C., Guo, B., Intermetallics 18 (2010) 871–876.CrossRefGoogle Scholar
Abioye, T. E., Clare, A. T., McCartney, D. G., J. Mater. Process. Technol. 217 (2015) 232–240.CrossRefGoogle Scholar
Kobayashi, S., Sato, K., Hayashi, E., Konno, T. J., Kaneno, Y., Takasugi, T., Intermetallics 23 (2012) 68–75.CrossRefGoogle Scholar