Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-15T01:57:42.570Z Has data issue: false hasContentIssue false
  • English
  • Français

Thermal-Spraying of Polymers and Polymer Blends

Published online by Cambridge University Press:  31 January 2011

J. A. Brogan
Get access

Extract

Thermal-spraying of polymers can be traced back to the 1940s, when polyethylene (PE) was first produced by E.I. du Pont de Nemours & Company. Early work with flame-spraying guns was unsuccessful because the equipment, designed for spraying metals, produced a flame that was both too hot and too short to melt the PE without degradation. The technology has advanced considerably in the past 20 years. Flame-spray equipment and hardware accessories have been designed by numerous companies (PFS Thermoplastics, Alamo, Eutectic + Castolin, etc.) specifically for polymeric materials. The new equipment provides either a lower flame temperature or uses special cooling shrouds to cool the center of the flame, providing a longer residence time at a lower temperature. Many plastics can now be completely melted in-flight and allow heat-sensitive components to be coated with plastic.

Type
Research Article
Information
MRS Bulletin , Volume 25 , Issue 7: Thermal Spray Coatings , July 2000 , pp. 48 - 53
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Dickinson, T.A., Org. Finishing (1950) p. 11.Google Scholar
2.Sweet, G.K., in Proc. Natl. Thermal Spray Conf. (ASM International, Materials Park, OH, 1993) p. 381.Google Scholar
3.Schadler, L.S., Laul, K.O., Smith, R.W., and Petrovicova, E., JTST 6 (4) (1997) p. 475.CrossRefGoogle Scholar
4.Mazur, S., Polymer Powder Technology, edited by Narkis, M. and Rosenzweig, N. (John Wiley & Sons, New York, 1996) p. 157.Google Scholar
5.Voyutskii, S.S., Rubber Chem. Technol. 30 (1957) p. 544.CrossRefGoogle Scholar
6.Prager, S. and Tirrell, M., J. Chem. Phys. 75 (10) (1981) p. 5194.CrossRefGoogle Scholar
7.Jud, K., Kausch, H., and Williams, J.G., J. Mater. Sci. 16 (1981) p. 204.CrossRefGoogle Scholar
8.Brogan, J.A., PhD dissertation, State University of New York, 1996.Google Scholar
9.Loustaunau, P.J. and Horton, D., Mater. Performance (1994) p. 32.Google Scholar
10.Glass, T.W. and dePay, J.A., in Proc. Natl. Thermal Spray Conf. (ASM International, Materials Park, OH, 1991) p. 345.Google Scholar
11.Brogan, J.A. and Berndt, C.C., J. Mater. Sci. 32 (1997) p. 2099.CrossRefGoogle Scholar
12.Brogan, J.A., Berndt, C.C., Simon, G.P., and Hewitt, D., J. Polym. Eng. Sci. 38 (11) (1998) p. 1873.CrossRefGoogle Scholar
13.Brogan, J.A., Margolies, J., Drozdz, S., Sampath, S., Herman, H., and Berndt, C.C., in Proc. Natl. Thermal Spray Conf. (ASM International, Materials Park, OH, 1995) p. 521.Google Scholar
14.Bao, Y. and Gawne, D.T., in Proc. Natl. Thermal Spray Conf. (ASM International, Materials Park, OH, 1993) p. 417.Google Scholar
15.Bao, Y. and Gawne, D.T., Surf. Eng. 11 (3) (1995) p. 215.CrossRefGoogle Scholar
16.Lima, R.S., Takimi, A.S., Lima, M.D., and Bergmann, C.P., in Proc. Natl. Thermal Spray Conf. (ASM International, Materials Park, OH, 1997) p. 215.Google Scholar
17.Allan, M.L., Berndt, C.C., Brogan, J.A., and Otterson, D., in Proc. 15th Int. Thermal Spray Conf. (ASM International, Materials Park, OH, 1998) p. 13.Google Scholar
18.Zhang, T., Gawne, D.T., and Bao, Y., in Proc. United Thermal Spray Conf. (ASM International, Materials Park, OH, 1997) p. 237.Google Scholar
19.Kawase, R. and Nakano, A., in Proc. Int. Thermal Spray Conf. (ASM International, Materials Park, OH, 1996) p. 257.Google Scholar
20.Lugscheider, E., Herbst, C., and Fischer, A., in Proc. Int. Thermal Spray Conf. (ASM International, Materials Park, OH, 1998) p. 19.Google Scholar
21.Charrier, J.M., Polymeric Materials and Processes (Hanser Publishers, New York, 1991).Google Scholar
22.La Mantia, F.P., Thermotropic Liquid Crystal Polymer Blends (Technomic, Lancaster, PA, 1993).Google Scholar
23.Donald, A.M., Liquid Crystalline Polymers (Cambridge University Press, New York, 1992).Google Scholar
24.Tufa, K.Y. and Gitzhofer, F., in Proc. Int. Thermal Spray Conf. (ASM International, Materials Park, OH, 1997) p. 223.Google Scholar
25.Kharitonov, V.V. and Yurkevich, O.R., translated from Inzhenerno-Fizicheskii Zhurnal 50 (3) (1986) p. 379.Google Scholar
26.Petrovicova, E., Knight, R., Schadler, L.S., and Twardowski, T.E., J. Appl. Polym. Sci., submitted for publication, 1999.Google Scholar
27.Varacalle, D.J., Couch, K.W., and Budinger, V.S., in Proc. Int. Thermal Spray Conf. (ASM International, Materials Park, OH, 1996) p. 19.Google Scholar
28.Brogan, J.A., Berndt, C.C., Claudon, A., and Coddet, C., Thermal Spray: Practical Solutions for Engineering Problems, edited by Berndt, C.C. (ASM International, Materials Park, OH, 1996) p. 221.Google Scholar
29.Phillips, P.J. and MacKnight, W.J., J. Polym. Sci. Part A-2: Polym. Chem. 8 (1970) p. 727.CrossRefGoogle Scholar
30.Brogan, J.A., Gross, K.A., Chen, Z., Berndt, C.C., and Herman, H., Thermal Spray Industrial Applications (ASM International, Materials Park, OH, 1994) p. 159.Google Scholar