Hostname: page-component-cd9895bd7-gxg78 Total loading time: 0 Render date: 2024-12-27T08:59:21.402Z Has data issue: false hasContentIssue false
  • English
  • Français

Vaporizing foil actuator welding

Published online by Cambridge University Press:  05 August 2019

Brian P. Thurston ,
Anupam Vivek ,
Bhuvi S.L. Nirudhoddi  and
Glenn S. Daehn
Brian P. Thurston
Affiliation:
Department of Materials Science, The Ohio State University, USA; Thurston.56@osu.edu
Anupam Vivek
Affiliation:
Department of Materials Science and Engineering, The Ohio State University, USA; vivek.4@osu.edu
Bhuvi S.L. Nirudhoddi
Affiliation:
Department of Materials Science and Engineering, The Ohio State University, USA; nirudhoddi.1@osu.edu
Glenn S. Daehn
Affiliation:
Department of Materials Science and Engineering, The Ohio State University, USA; Daehn.1@osu.edu
Get access

Abstract

Vaporizing foil actuator welding is a form of impact welding, which can be carried out without the use of chemical explosives. Operating at smaller length scales, but with similar driving pressures as explosive welding, vaporizing foil actuator welding is capable of welding a wide variety of advanced and dissimilar metal combinations. With negligible heating developing during the process, thermal distortion does not occur, and the base-metal properties are retained in the weld. In this article, vaporizing foil actuator welding of an automotive grade aluminum and steel pair is discussed. A currently functional and complete welding system that can be used for research as well as low volume production is also discussed.

Keywords

Alsteelwelding
Type
Joining of Dissimilar Lightweight Materials
Information
MRS Bulletin , Volume 44 , Issue 8: Joining of Dissimilar Lightweight Materials , August 2019 , pp. 637 - 642
Copyright
Copyright © Materials Research Society 2019 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Cai, W., Daehn, G., Vivek, A., Li, J., Khan, H, Mishra, R.S., Komarasamy, M., J. Manuf. Sci. Eng. 141, 031012 (2019).CrossRefGoogle Scholar
Hovanski, Y., Upadyay, P., Kleinbaum, S., Carlson, B., Boettcher, E., Ruokolainen, R., JOM 69, 1060 (2017).CrossRefGoogle Scholar
Findik, F., Mater. Des. 32, 1081 (2011).CrossRefGoogle Scholar
Psyk, V., Risch, D, Kinsey, B.L., Tekkaya, A.E., Kleiner, M., J. Mater. Process. Technol. 211, 787 (2011).CrossRefGoogle Scholar
Berlin, A., “Magnetic Pulse Welding of Mg Sheet,” Master’s thesis, University of Waterloo (2011).Google Scholar
Vivek, A., Hansen, S.R., Liu, B.C., Daehn, G.S., J. Mater. Process. Technol. 213 (12), 2304 (2013).CrossRefGoogle Scholar
Vivek, A., Presley, M., Flores, K.M., Hutchinson, N.H. Daehn, G.S., Mater. Sci. Eng. A 634, 14 (2015).CrossRefGoogle Scholar
Kapil, A., Lee, T., Vivek, A., Cooper, R., Hetrick, E., Daehn, G.S., J. Manuf. Proc. 37, 42 (2019).CrossRefGoogle Scholar
Hansen, S.R., “Vaporizing Foil Actuator Process Parameters: Input Characteristics, Energy Deposition, and Pressure Output,” PhD dissertation, The Ohio State University (2018).Google Scholar
https://www.osha.gov/SLTC/noisehearingconservation/loud.html.Google Scholar
Kapil, A., Lee, T., Vivek, A., Bockbrader, J., Abke, T., Daehn, G.S., J. Mater. Process. Technol. 255, 219 (2018).CrossRefGoogle Scholar
Sridharan, N., Poplawsky, J., Vivek, A., Bhattacharya, A., Guo, W., Meyer, H., Mao, Y., Lee, T., Daehn, G., Mater. Charact. 151, 119 (2019).CrossRefGoogle Scholar
Liu, B., Vivek, A., Presley, M., Daehn, G.S., Metall. Mater. Trans. A 49 (3), 899 (2018).CrossRefGoogle Scholar