Hostname: page-component-78c5997874-m6dg7 Total loading time: 0 Render date: 2024-11-10T07:30:45.772Z Has data issue: false hasContentIssue false
  • English
  • Français

Processing and Characterization of Short Glass Fiber/ABS/Polyamide-6 Composites

Published online by Cambridge University Press:  01 February 2011

Guralp Ozkoc ,
Goknur Bayram  and
Erdal Bayramli
Guralp Ozkoc
Affiliation:
Department of Polymer Science and Technology, Middle East Technical University, Inonu Bulvari, 06531, Ankara, TURKEY.
Goknur Bayram
Affiliation:
Department of Chemical Engineering, Middle East Technical University, Inonu Bulvari, 06531, Ankara, TURKEY.
Erdal Bayramli
Affiliation:
Department of Chemistry, Middle East Technical University, Inonu Bulvari, 06531, Ankara, TURKEY.
Get access

Abstract

The main objective of this study is to determine the effects of short glass fiber (SGF) content and extrusion conditions such as screw speed and barrel temperature, on the mechanical properties and morphologies of structural composites produced by compounding SGFs with poly (acrylonitrile-butadiene-styrene) (ABS). It was also aimed to determine the effects of adhesion at the fiber/matrix interface, which was promoted by incorporation of polyamide-6 (PA6) to the ABS/SGF composite. Results showed that increasing screw speed during extrusion decreased the average fiber length; therefore mechanical properties of the composites affected negatively. The increasing extrusion temperature decreased the fiber length degradation and higher tensile strength and modulus values were obtained. The use of PA6 in composites increased the interfacial adhesion, which was supported by SEM microphotographs; therefore, improved mechanical properties were obtained.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 856: Symposium BB – Multicomponent Polymer Systems-Phase Behavior, Dynamics, and Applications , 2004 , BB10.18
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Ramsteiner, F. and Theysohn, R., Composite, 35, 111, (1979).Google Scholar
2. Fu, Y. S., Lauke, B., Mader, E., Yue, Y. C. and Hu, X., Composites Part A, 31, 1117 (1998).Google Scholar
3. Fu, Y. S. and Lauke, B., Composites Part A, 29, 631 (1998)Google Scholar
4. Laura, D. M., Keskkula, H., Barlow, J. W. and Paul, D. R., Polymer, 43, 4673, (2002).Google Scholar
5. Eberhardt, C., Clarke, A., Wincent, M., Giroud, T. and Flouret, S., Composite Science and Technology, 61, 1961, (2001).Google Scholar
6. Park, S.J., Jin, S.J. and Lee, R. J., Journal of Adhesion, 14, 1677, (2000).Google Scholar
7. Pak, H. S. and Caze, C., Journal of Applied Polymer Science, 65, 143, (1997).Google Scholar
8. Nielsen, L. E. and Landel, F. R., Mechanical Properties of Polymers and Composites, 2nd Ed., (Marcel Dekker, 1994).Google Scholar
9. Yow, B. N., Ishıaku, U. S., Mohd Ishak, Z. A. and Karger-Kocsis, J., Journal of Applied Polymer Science, 84, 1233, (2002).Google Scholar
10. Yilmazer, U., Composite Science and Technology, 44, 119, (1992).Google Scholar
11. Ozkoc, G., Bayram, G. and Bayramli, E., Polymer, 45, 8957, (2004).Google Scholar
12. Thomasson, J. L. and Vlug, M. A., Composites Part A, 27, 477, (1996).Google Scholar
13. Modern Plastic Encyclopedia, ABS, 6, (McGraw Hill, 1986).Google Scholar