Hostname: page-component-6bf8c574d5-t27h7 Total loading time: 0 Render date: 2025-02-22T16:04:34.953Z Has data issue: false hasContentIssue false
  • English
  • Français

A Technique for the Preparation of Thin-Film Cross-Sections for Transmission Electron Microscopy

Published online by Cambridge University Press:  16 February 2011

M. Libera ,
T. A. Nguyen  and
C. Hwang
M. Libera
Affiliation:
Stevens Institute of Technology, Hoboken, NJ
T. A. Nguyen
Affiliation:
IBM Almaden Research Center, San Jose, CA
C. Hwang
Affiliation:
IBM General Products Division, San Jose, CA
Get access

Abstract

A number of techniques for producing TEM cross-sections of thin films have been described in recent years as the need for improved and more-thorough microstructural study of thin-film materials has grown. We have developed a method for producing such cross-sections which involves little sophisticated equipment other than an ion mill for thinning. Following the method of Bravman and Sinclair (J. Elec. Micrs. Tech 1,53–61 (1984)), the film of interest is either deposited on or epoxied to a silicon wafer and a composite of six silicon beams (=3mm × 25mm × 0.5mm) is fabricated. Slices are cut from this composite perpendicular to the film plane, and each slice is mechanically thinned by a series of simple grinding and polishing steps to ∼ 50–100μm. Dimpling is not necessary. The specimen is mounted onto a slotted TEM grid which provides a vehicle for safe handling, and the specimen is ion milled to perforation. We have found the technique to be relatively fast, reliable, and simple. Its success hinges on minimizing the amount of direct handling required when the specimen is thin and fragile. We present a detailed recipe describing its various steps and show typical results from studies of thin films for data-storage applications.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 199: Symposium W – Specimen Preparation for Transmission Electron Microscopy of Materials II , 1990 , 243
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1) Bravman, J.C. and Sinclair, R., “The Preparation of Cross- Section Specimens for Transmission Electron Microscopy,” J. Electron Microscopy Technique 1, 53–61 (1984).Google Scholar
2) Specimen Preparation for Transmission Electron Microscopy of Materials, ed. by Bravman, J., Anderson, R., and McDonald, M., Materials Research Society Symposium Proceedings, V 115, Pittsburgh, PA (1988).Google Scholar
3) “Magnetic Recording Materials,” MRS Bulletin topical issue, March (1990).Google Scholar
4) Yogi, T. et al., IEEE Trans. Magn. 24, 2727 (1988).Google Scholar
5) Nguyen, T.A. et al., Proceedings of the 12th ICEM (in press).Google Scholar
6) Yogi, T. et al., IEEE Trans. Magn., (in press)Google Scholar
7) “Optical Recording Materials,” MRS Bulletin topical issue, April (1990).Google Scholar
8) “Ge Supersaturation in Laser-Heated Te-Ge-Sn Thin Films,” Libera, M., Chen, M., and Rubin, K.A., to be submitted to the J. of Matls. Research.Google Scholar
9) “The Microstructural Response of Multilayer Chalcogenide Films to Local Laser Heating,” Libera, M., Chen, M., and Rubin, K.A., Optical Materials: Processing and Science, ed. by Poker, D.B. et al., Materials Research Society, Pittsburgh (1989).Google Scholar