Hostname: page-component-6bf8c574d5-b4m5d Total loading time: 0 Render date: 2025-02-22T16:39:56.558Z Has data issue: false hasContentIssue false
  • English
  • Français

Characterization of Tungsten Nucleation Layers Deposited Using Various Sih4 and Wf6 Flows

Published online by Cambridge University Press:  25 February 2011

V.V.S. Rana ,
M. Eizenberg ,
S. Ghanayem ,
J. Roberts  and
A.K. Sinha
V.V.S. Rana
Affiliation:
Applied Materials, Inc., 3100 Bowers Ave., Santa Clara, CA 95054
M. Eizenberg
Affiliation:
Applied Materials, Inc., 3100 Bowers Ave., Santa Clara, CA 95054 Technion Institute of Technology, Department of Materials Engineering, Haifa 32000, Israel
S. Ghanayem
Affiliation:
Applied Materials, Inc., 3100 Bowers Ave., Santa Clara, CA 95054
J. Roberts
Affiliation:
Applied Materials, Inc., 3100 Bowers Ave., Santa Clara, CA 95054
A.K. Sinha
Affiliation:
Applied Materials, Inc., 3100 Bowers Ave., Santa Clara, CA 95054
Get access

Abstract

Chemical vapor deposition (CVD) of tungsten nucleation films is typically done using silane (SiH4) reduction of tungsten hexafluoride (WF6). For SiH4/WF6 flow ratios of ≤ 1, pure tungsten of bulk density and resistivity is deposited. Upon increasing the ratio to 2, nearly 40 at.% Si is incorporated in tungsten films. At a ratio of 3, hexagonal WSi2 is deposited, and at ratios of > 6 WSi2 along with silicon is deposited. A maximum in deposition rate is obtained for WSi2 at the ratio of 3, and the deposition rate drops as more silicon is being deposited. The step coverage of films drops dramatically as one moves away from pure W films. The deposition of these films takes place without any incubation time.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 337: Symposium B – Advanced Metallization for Devices and Circuits—Science, Technology and Manufacturing III , 1994 , 569
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1 Rana, V.V.S., Taylor, J.A., Holschwandner, L.H., and Tsai, N.S., in Tungsten and Other Refractory Metals for VLSI Applications II, ed. by Broadbent, E.K. (MRS, Pittsburgh, PA), 1987, p.187.Google Scholar
2 Barber, R., and Shenasa, M., in Tungsten and OtherAdvanced Metals for ULSI Applications in 1990, ed, Smith, by G.C. and Blumenthal, R. (MRS, Pittsburgh, PA), 1991, p. 275.Google Scholar
3 Rutten, M., Greenwell, d., Luce, S., Dreves, R., in Advanced Metalization for ULSI Applications, ed, by Rana, V.V.S., Joshi, R.V., and Ohdomari, I., (MRS, Pittsburgh, PA), 1992, p. 277.Google Scholar
4 Suzuki, M., Kobayashi, N., and Mukai, K., in Tungsten and Other Advanced Metals for VLSI/ULSI Applications V, ed. by S, Simon Wong and Furukawa, S. (MRS, Pittsburgh, PA), 1990, p. 259.Google Scholar
5 Van der Jeugd, C.A., Verbruggen, A.H., Leusiak, G.J., Janssen, G.C.A.M., and Radelaar, S., ibid., p. 267.Google Scholar
6 Schmitz, J.E. J., Buiting, M.J., and Ellwanger, R.C., in Tungsten and Other Refractory Metals for VLSI/ULSI Applications IV, ed. by Blewer, R.S. and McConica, C.M., (MRS, Pittsburgh, PA), 1989, p. 27.Google Scholar