Hostname: page-component-6bf8c574d5-b4m5d Total loading time: 0 Render date: 2025-02-22T16:55:51.684Z Has data issue: false hasContentIssue false
  • English
  • Français

Deposition of Ti(C,N) Thick Films by ILPCVD Starting from TDMAT

Published online by Cambridge University Press:  10 February 2011

S. Gilles ,
N. Bourhila ,
J. P. Senateur ,
R. Madar ,
R. A. Levy  and
E. Blanquet
S. Gilles
Affiliation:
INPG-LMGP, UMR 5628 CNRS, BP 46, 38402 St Martin d'Hères, (France)
N. Bourhila
Affiliation:
INPG-LMGP, UMR 5628 CNRS, BP 46, 38402 St Martin d'Hères, (France)
J. P. Senateur
Affiliation:
INPG-LMGP, UMR 5628 CNRS, BP 46, 38402 St Martin d'Hères, (France)
R. Madar
Affiliation:
INPG-LMGP, UMR 5628 CNRS, BP 46, 38402 St Martin d'Hères, (France)
R. A. Levy
Affiliation:
NJIT, University Heights, Newark, New Jersey 07102, (USA)
E. Blanquet
Affiliation:
INPG-LTPCM, UMR 5614 CNRS, BP 75, 38402 St Martin d'Hères, (France).
Get access

Abstract

Ti(C,N) films have been deposited from tetrakis(dimethylamido)titanium (TDMAT) and ammonia by CVD at low pressure using pulsed Injection technique (ILPCVD). This procedure allows us to easily deposit Ti(C,N) films with a good reproducibility. It is an efficient technique to control growth rates and composition of coatings. The liquid TDMAT undergoes no degradation during deposition since it is kept at room temperature. Ti(C,N) films, with fee structure and fine grains were deposited at substrate temperature varying from 200 to 500 °C. Composition of films is controlled by substrate temperature and ammonia flow rate. Growth rates as high as 2 μm/min are reached for deposition of Ti(C,N) films at low temperature (350 °C).

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 495: Symposium W – Chemical Aspects of Electronic Ceramics Processing , 1997 , 177
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Bendavid, A., Martin, P. J., Netterfield, R. P. and Kinder, T. J., Sur. Coat. Technol., 70, p. 97 (1994).Google Scholar
2. Anderbouhr, S., Blanquet, E., Ghetta, V. and Bernard, C., Electrochem. Soc. Proc. of the XVIth Intern. Conf. and EUROCVD-11, Paris, 97–25, p. 356 (1997).Google Scholar
3. Fix, R., Gordon, R. G. and Hoffman, D. M., Chem. Mater., 2, p. 1138 (1991).Google Scholar
4. Bae, Y. W., Lee, W. Y., Besmann, T. M., Blau, P. J. and Riester, L., Mater. Res. Soc. Symp. Proc. Vol. 363, p. 245 (1995).Google Scholar
5. Musher, Joshua N. and Gordon, Roy G., J. Mater. Res., 11, N°4, p. 989 (1996).Google Scholar
6. Marcadal, C., Richard, E., Torres, J., Palleau, J., Ulmer, L. and Perroud, L., in European Workshop Materials for Advanced Metallization (Villard-de-Lans, France), p. 54 (1997)Google Scholar
7. Jimenez, C., Gilles, S., Bernard, C. and Madar, R., Sur. Coat. Technol., 76–77, p. 237 (1995)Google Scholar
8. Gilles, S., PhD Thesis, National Polytechnic Institut of Grenoble France (1997)Google Scholar
9. Bourhila, N., Feiten, F., Senateur, J. P., Schuster, F., Madar, R. and Abrutis, A.,, Electrochem. Soc. Proc. of the XVIth Intern. Conf. and EUROCVD-11, Paris, 97–25, p. 417 (1997).Google Scholar
10. Feiten, F., Senateur, J. P., Weiss, F., Madar, R. and Abrutis, A., Journal de Physique IV, Colloque C5, supplement au Journal de Physique II, Vol. 5, p. C5–1079 (1995)Google Scholar
11. Senateur, J. P., Feiten, F., Pignard, S., Weiss, F., Abrutis, A., Bigelyte, V., Teiserskis, A. and Saltyle, Z.. To be published in J. of Alloys and Compounds.Google Scholar
12. Bourhila, N., Thomas, N., Palleau, J., Torres, J., Bernard, C. and Madar, R., Appl. Surf. Sci. 91, p. 175(1995).Google Scholar