Hostname: page-component-cd9895bd7-q99xh Total loading time: 0 Render date: 2024-12-28T06:33:55.906Z Has data issue: false hasContentIssue false
  • English
  • Français

Effects of matrix composition and sample preparation on instant release fractions from high burnup nuclear fuel

Published online by Cambridge University Press:  03 July 2014

O. Roth ,
J. Low  and
K. Spahiu
O. Roth
Affiliation:
Studsvik Nuclear AB, Hot Cell Laboratory, SE-611 82 Nyköping, Sweden
J. Low
Affiliation:
Studsvik Nuclear AB, Hot Cell Laboratory, SE-611 82 Nyköping, Sweden
K. Spahiu
Affiliation:
SKB, Box 250, SE-101 24, Stockholm, Sweden.
Get access

Abstract

The rapid release of fission products segregated either to the gap between the fuel and the cladding or to the UO2 grain boundaries from spent nuclear fuel in contact with water (often referred to as the instant release fraction - IRF) is of interest for the safety assessment of geological repositories for spent fuel due to the potential dose contribution. In September 2012 a study was initiated with the aim of comparing the instant release behavior of fuels with and without additives/dopants. Preliminary results from this (ongoing) study indicate that the release of uranium during the first contact periods was higher than during the tests with fuel segments, even though the fuel was cut open recently [1]. This could be due to the sample preparation method which included axial cutting of the cladding in order to remove the fuel fragments used in the study. In the present work, leaching data from both studies are presented and the releases are discussed comparing the two sample preparation methods and considering the effect of matrix composition. The leaching studies have been performed in air using 10 mM NaCl + 2 mM NaHCO3 as leaching solution.

Keywords

nuclear materialsUcorrosion
Type
Articles
Information
MRS Online Proceedings Library (OPL) , Volume 1665: Symposium NW – Scientific Basis for Nuclear Waste Management XXXVII , 2014 , pp. 261 - 266
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Zwicky, H-U., Low, J., Ekeroth, E., SKB TR 11–03, (2011).Google Scholar
Johnson, L. H. and McGinnes, D. F., Nagra Technical Report NTB 02-07, (2002).Google Scholar
Johnson, L., Poinssot, C., Ferry, C., Lovera, P., Nagra Tech.Rep. NTB 04–08, (2004).Google Scholar
Johnson, L. H. and Tait, J. C., SKB TR 97–18, (1997).Google Scholar
Ferry, C., Piron, J-P., Poulesquen, A, Poinssot, C., MRS Symp. Proc. 1107, 447–454 (2008).CrossRefGoogle Scholar
Backman, K. et al. ., in: IAEA-TECDOC-1654, pp. 117–126 (2010).Google Scholar
Roth, O., Low, J., Granfors, M., Spahiu, K., MRS Symp. Proc. 1518, 145–150 (2013).CrossRefGoogle Scholar
Johnson, L. et al. ., J. Nucl. Mater., 420, 54–62 (2012).CrossRefGoogle Scholar
Izmer, A., Boulyga, S. F. and Becker, J. S., J. Anal. At. Spectrom. 18 1339–1345 (2003).CrossRefGoogle Scholar
Haynes, W., CRC handbook of chemistry and physics: a ready-reference book of chemical and physical data. Boca Raton, FL: CRC Press, 2011.Google Scholar
Thomas, L., Einziger, R., Buchanan, H., J. Nucl. Mater. 201, 310–319 (1993).10.1016/0022-3115(93)90187-4CrossRefGoogle Scholar
Matzke, H., Spino, J., J. Nucl. Mater. 248 170–179 (1997).CrossRefGoogle Scholar