Hostname: page-component-745bb68f8f-s22k5 Total loading time: 0 Render date: 2025-01-15T06:45:06.592Z Has data issue: false hasContentIssue false
  • English
  • Français

Formation of Cubic Ll2 Phases from Al3Ti and Al3 Zr by Transition Metal Substitutions for Al

Published online by Cambridge University Press:  28 February 2011

C. J. Sparks ,
W. D. Porter ,
J. H. Schneibel ,
W. C. Oliver  and
C. G. Golec
C. J. Sparks
Affiliation:
Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831-6118
W. D. Porter
Affiliation:
Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831-6118
J. H. Schneibel
Affiliation:
Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831-6118
W. C. Oliver
Affiliation:
Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831-6118
C. G. Golec
Affiliation:
ORNL Student Intern, Purdue University at Calumet, Hammond, IN 46323
Get access

Abstract

Alloys of (AlxM1−x)3Ti where M is V, Cr, Mn, Fe, Co, Nb, W, Fe + Ga or Fe + Ga + Mn were fabricated to form the Ll2 cubic phase, tested for ductility, and characterized by lattice parameter, microstructure, quantitative phase analysis, and phase composition. The elements V, Co, Nb, W, Fe + Ga and Fe + Ga + Mn are hereby newly found Ll2 formers in Al3Ti. Both X-ray diffraction and microprobe analysis were used to identify the phases, their volume fractions and compositions. The amount of ternary addition found in the Ll2 cubic phase varied between 4 and 12 atomic percent. This amount of ternary addition decreased as the atomic radius of the elemental addition increased. Pettifor's Mendeleev number was a useful guide in the selection of elements to form the Ll2 phase but did not correlate strongly with the amount of the ternary addition. For the DO23 phase of Al3Zr, the elements V, Mn, and Co were added to the list of Ni, Cu, Fe, and Cr as elements known to form the Ll2 phase. Little if any ductility was observed in these cubic Ll2 phases which readily cleaved with transgranular failure. To achieve ductility and toughness, more than transformation of these compositions from a lower to a higher symmetry crystal structure will be required.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 186: Symposium I – Alloy Phase Stability and Design , 1990 , 175
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Liu, C. T., International Metals Review, 29, 168 (1984).Google Scholar
[2] Kumar, K. S. and Pickens, J. R., Scripta Met. 22, 1015 (1988).Google Scholar
[3] Kumar, K. S. and Pickens, J. R., Dispersion Strengthened Aluminum Alloys, Kim, Y.-W. and Griffith, W., eds., p. 763, TMS, Warrendale, PA (1988).Google Scholar
[4] Tarnacki, J. and Kim, Y.-W., Scripta Met. 22, 329 (1988).Google Scholar
[5] Huang, S. C., Hall, E. L., and Gigliotti, M.F.X., J. Mater. Res. 3, 1 (1988).Google Scholar
[6] Zhang, S., Nic, J. P., and Mikkola, D. E., Scripta Met. 24, 57 (1990).Google Scholar
[7] Schneibel, J. H., Becher, P. F., and Horton, J. A., J. Mater. Res. 3, 1272 (1988).Google Scholar
[8] Schneibel, J. H. and Porter, W. D., p. 335 in Mater. Res. Soc. Symp. Proc., Vol. 133, 1989.Google Scholar
[9] Raman, A. and Schubert, K., Z. Metallkde. 56, 99 (1965).Google Scholar
[10] Seibold, A., Z. Metallkde. 72, 712 (1981).Google Scholar
[11] Porter, W. D., Hisatsune, K., Sparks, C. J., Oliver, W. C., and Dhere, A., p. 657 in Mater. Res. Soc. Symp. Proc., Vol. 133, 1989.Google Scholar
[12] Moruzzi, V. L., Janak, J. F., and Williams, A. R., Calculated Electronic Properties of Metals, Pergamon, New York, 1978.Google Scholar
[13] Pettifor, D. G., J. Phys. C19, 285 (1986).Google Scholar
[14] Laves, F. in Theory of Alloy Phases, American Society for Metals, Metal Park, OH, 1956, p. 124.Google Scholar
[15] Wu, Y. P., Tso, N. C., Sanchez, J. M., and Tien, J. K., Acta Metall. 37, 2835 (1989).Google Scholar