Hostname: page-component-78c5997874-8bhkd Total loading time: 0 Render date: 2024-11-13T15:13:25.579Z Has data issue: false hasContentIssue false
  • English
  • Français

Hardness and modulus of CrNx coatings

Published online by Cambridge University Press:  11 February 2011

G. C. A. M. Janssen ,
R. Hoy  and
J.-D. Kamminga
G. C. A. M. Janssen
Affiliation:
Department of Material Science and Technology, Delft University of Technology, the Netherlands, e-mail: g.c.a.m.janssen@tnw.tudelft.nl
R. Hoy
Affiliation:
Netherlands Institute for Metals Research, Delft, the Netherlands
J.-D. Kamminga
Affiliation:
Netherlands Institute for Metals Research, Delft, the Netherlands
Get access

Abstract

Two series of CrNx coatings have been deposited in an industrial PVD set-up. It is shown that for an increased ion bombardment on the growing film the hardness (H) and Young's modulus (E) are independent on composition. For these hard coatings the elastic strain to failure or plasticity limit (H/E) is 0.11. The coating fails long before it is stretched to its plasticity limit. Deformation of the coating by 1% already leads to crack formation. It is argued that the cause of this failure is the low work of fracture of the coating combined with flaws in the coating.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 750: Symposium Y – Surface Engineering 2002–Synthesis, Characterization and Applications , 2002 , Y1.2
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Archard, J., J. Appl. Phys., 24, 981 (1953).Google Scholar
2. Tabor, D., The hardness of metals, Oxford University Press, 1951.Google Scholar
3. Knapp, J.A., Folstaedt, D.M.. Myers, S.M., Barbour, J.C., and Friedmann, T.A., J. Appl. Phys., 85, 1460 (1999).Google Scholar
4. Rodrigo, A., Perillo, P., Ichimura, H., Surf. Coat. Technol., 124, 87 (2000).Google Scholar
5. Oberle, T.L., Journal of Metals, June 1951, 438.Google Scholar
6. Leyland, A. and Matthews, A., Wear, 246, 1 (2000).Google Scholar
7. Veprek, Stan and Argon, Ali S., J. Vac. Sci. Technol. B20, 650 (2002).Google Scholar
8. Gordon, J.E., The new science of strong materials, Penguin Books, 1968.Google Scholar
9. Janssen, G.C.A.M., Kamminga, J.-D., Sloof, W.G., in Nanophase and Nanocomposite Materials IV edited by Komarneni, S., Vaia, R.A., Lu, G.Q., Matsushita, J-I., Parker, J.C., (Mater. Res. Soc. Proc. 703, Warrendale, PA, 2002) pp. V3.24.1–6.Google Scholar
10. Janssen, G.C.A.M. and Hoy, R., J. Vac. Sci. Technol. A, submitted for publication.Google Scholar
11. Kamminga, J.-D., Hoy, R., Janssen, G.C.A.M., Surf. Coat. Technol., submitted for publication.Google Scholar