Hostname: page-component-745bb68f8f-cphqk Total loading time: 0 Render date: 2025-01-15T07:00:37.914Z Has data issue: false hasContentIssue false
  • English
  • Français

Preparation and Characterization Of SrTio3 Thin Films Using ECR Plasma Assisted MOCVD

Published online by Cambridge University Press:  10 February 2011

Joon Sung Lee ,
Han Wook Song ,
Dae Sung Yoon ,
Byung Hyuk Jun ,
Byoung Gon Yu ,
Zhong Tao Jiang ,
Won Jong Lee  and
Kwangsoo No
Joon Sung Lee
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Taejon, Korea
Han Wook Song
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Taejon, Korea
Dae Sung Yoon
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Taejon, Korea
Byung Hyuk Jun
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Taejon, Korea
Byoung Gon Yu
Affiliation:
Electronics and Telecommunications Research Institute, Taejon, Korea
Zhong Tao Jiang
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Taejon, Korea
Won Jong Lee
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Taejon, Korea
Kwangsoo No
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Taejon, Korea
Get access

Abstract

SrTiO3 thin films were prepared on Si(p-type 100) and Pt/SiO2/Si substrates using ECR plasma (or without ECR plasma) assisted MOCVD. Sr(TMI-D)2 and Ti-isopropoxide were used as Sr and Ti metal organic sources, respectively. Perovskite SrTiO3 films were obtained at relatively low temperature of 500°C (using ECR oxygen plasma. Experimental results indicated that higher deposition temperature and ECR oxygen plasma increase the crystallinity, the dielectric constant and the leakage current density. The dielectric constant and the dielectric loss were 222 and 0.04, respectively, for 1234 Å thin SrTiO3 film (Sr/(Sr+Ti)=0.5). The leakage current density was 3.78 × 10−7 A/cm2 at 1.0V, and the dielectric breakdown field was 0.57MV/cm. SEM analyses showed that SrTiO3 films have a uniform and fine grain structure. In terms of step coverage, a lateral step coverage of 50% at 0.8 μm step (the aspect ratio was 1) was obtained with the thickness uniformity of ± 0.5% and the composition uniformity of ±1.2% at 4′′ wafer.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 415: Symposium BB – Metal-Organic Chemical Vapor Deposition of Electronic Ceramics II , 1995 , 183
Copyright
Copyright © Materials Research Society 1996

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Pennebaker, W. B., IBM J. Res. Develop., 686 (1969)Google Scholar
[2] Matsubara, S. et al., Mat. Res. Soc. Symp. Proc., 200, 243 (1990)Google Scholar
[3] Miyasaka, Y. et al., Proceedings of the 7th ISAF., 121 (1990)Google Scholar
[4] Sakuma, T. et al., Appl. Phys. Lett., 57, 23, 2431, (1990)Google Scholar
[5] Pinizzotto, R. F. et ai., Mat. Res. Soc. Symp. Proc., 243, 463 (1992)Google Scholar
[6] Feil, W. A. et al., J. Appl. Phys., 67, 8, 15 (1990)Google Scholar
[7] Yamaguchi, H. et al., Jpn. J. Appl. Phys., 32, 9B, 4069 (1993)Google Scholar
[8] Lesaicherre, P-Y. et al., Mat. Res. Soc. Symp. Proc., 310, 487 (1993)Google Scholar
[9] Kimura, T. et al., Jpn. J. Appl. Phys., 33, 9B, 5119 (1994)Google Scholar
[10] Liang, S. et al., Appl. Phys. Lett., 64, 27, 3563 (1994)Google Scholar
[11] Kobayashi, I. et al., Jpn. J. Appl. Phys., 33, 8, 4680 (1994)Google Scholar
[12] Schwarberg, J. et al., Anal. Chem., 42, 14, 1828 (1970)Google Scholar
[13] Tsu, R. et el., Mat. Res. Soc. Symp. Proc., 361, 275 (1995)Google Scholar